Home > Kyocera > Printer > Kyocera FS C5250DN User Manual

Kyocera FS C5250DN User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Kyocera FS C5250DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 73 Kyocera manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							4-43Using the Operation Panel
    EcoPrint Mode (Selecting the EcoPrint mode)
    By enabling EcoPrint mode, you can minimize the amount of toner used 
    during printing. Because images printed in this mode may be slightly 
    coarser than those printed in standard resolution, you should use 
    EcoPrint for test prints or other situations where high-quality prints are not 
    required.
    Use the procedure below to select EcoPrint mode. The default setting is 
    Off
    .
    1Press  Z while >Print Quality >  is displayed.
    2Press U or  V repeatedly until  >>EcoPrint Mode  appears.
    3Press [OK]. A blinking question mark ( ?) appears.
    4Select  On or  Off using  U or  V.
    5Press  [OK].
    6Press [MENU] . The display returns to Ready .
    Page Set (Setting pagination)
    In Page Set menus, you can set the number of copies, page orientation, 
    and other settings regarding pagination.
    The options available in Page Set are as follows:
    • Copies (Number of copies)
    • Orientation (Print orientation)
    • Wide A4 (Wide A4 pitch)
    • XPS FitTo Page (Print area setting for XPS data)
    • TIFF/JPEG Size (Print mode setting for TIFF/JPEG files)
    1Press  Z while Print Settings >  is displayed.
    2Press U or  V repeatedly until  >Page Set > appears.
    Copies (Number of copies)
    You can set the number of copies of each page to be printed for the 
    current interface. 
    1Press Z while >Page Set >  is displayed.
    2Press U or  V repeatedly until  >>Copies appears.
    3Press [OK]. A blinking cursor ( _) appears.
    4Press  U or V  to increase or decrease, respectively, the value at the 
    blinking cursor. The number of copies can be set between  1 and  999. 
    Use  Y and Z  to move the cursor right and left.
    5When the desired size is displayed, press  [OK].
    6Press  [MENU] . The display returns to Ready .
    >>EcoPrint Mode
    ? Off
    >Page Set>
    >>Copies
    001
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Using the Operation Panel
    4-44
    Orientation (Print orientation)
    You can select portrait (upright) or landscape (sideways) page 
    orientation. 
    1Press  Z while >Page Set >  is displayed.
    2Press U or  V repeatedly until  >>Orientation  appears.
    3Press [OK]. A blinking question mark ( ?) appears.
    4Select  Portrait  or Landscape  using U or V. 
    5Press  [OK].
    6Press  [MENU] . The display returns to Ready .
    Wide A4 (Wide A4 pitch)
    Turn this to On to increase the maximum number of characters that can 
    be printed in a line for an A4 page (78 characters at 10 pitch) and Letter 
    size page (80 characters at 10 pitch). This setting is only effective in PCL 
    6 emulation.
    1Press  Z while >Page Set >  is displayed.
    2Press U or  V repeatedly until  >>Wide A4 appears.
    3Press [OK]. A blinking question mark ( ?) appears.
    4Select  On or  Off using  U or  V. 
    5Press  [OK].
    6Press [MENU] . The display returns to Ready .
    XPS FitTo Page (Print area setting for XPS data)
    Select On in this setting to enlarge or reduce XPS files to fit the printable 
    area during printing.
    1Press  Z while >Page Set >  is displayed.
    2Press U or  V repeatedly until  >>XPS FitTo Page  appears. 
    3Press [OK]. A blinking question mark ( ?) appears.
    Portrait Orientation
    A
    Landscape Orientation
    A
    >>Orientation
    ? Portrait
    >>Wide A4
    ? Off
    >>XPS FitTo Page
    ? Off
    Downloaded From ManualsPrinter.com Manuals 
    						
    							4-45Using the Operation Panel
    4Select 
    On or  Off using  U or  V.
    5Press  [OK].
    6Press [MENU] . The display returns to Ready .
    TIFF/JPEG Size (Print mode setting for TIFF/JPEG files)
    Use this setting to select the printing method used when TIFF or JPEG 
    files are printed directly. The default setting is  Paper Size.
    1Press Z while >Page Set >  is displayed.
    2Press U or  V repeatedly until  >>TIFF/JPEG Size  appears. 
    3Press [OK]. A blinking question mark ( ?) appears.
    4Press  U or  V repeatedly until the desired print mode is displayed. 
    The list shows the following print modes:
    Paper Size  (scaled to fit the paper size)
    Images are resized so that they fill the paper size when printed.
    Image Resolution  (matched to the image resolution)
    Image files are printed at the reso lution specified in the resolution 
    information. Images with no resolution information are printed using 
    the Paper Size setting.
    Print Resolution  (matched to the print resolution)
    Images are printed using a 1-to-1 correspondence between the 
    image file pixels and printed dots. For example, the printed size of a 
    600 × 300-pixel image file is 1 inch × 1/2 inch.
    5Press  [OK].
    6Press [MENU] . The display returns to Ready .
    >>TIFF/JPEG Size
    ? Paper Size
    Note  Images are automatically rotated during printing to provide 
    a closer match between the aspect ratios of the image file and the 
    paper used for printing.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Using the Operation Panel
    4-46
    Network (Network settings)
    This printer supports TCP/IP and TCP/IP (IPv6) protocols.
    IP is an abbreviation for Internet Protocol. This printer routinely uses the 
    TCP/IP (IPv4) protocol, but provides a separate setting for the next-
    generation IP, IPv6. 
    TCP/IP (IPv4) uses 32-bit IP addresses, but the rapid growth in the 
    number of Internet users has resulted in a shortage of IP addresses. IPv6 
    was developed to expand the range of available IP addresses by using 
    128-bit IP addresses. 
    The options available in the Network settings are as follows:
    • TCP/IP (IPv4 settings)
    • TCP/IP (IPv6) (IPv6 settings)
    1Press  [MENU] .
    2Press U or  V repeatedly until  Network > appears.
    TCP/IP (IPv4 settings)
    This selects the settings for TCP/IP (IPv4).
    The TCP/IP system refers to the Internet system, which has a 5-layer 
    structure consisting of the interface layer, link layer, network (IP) layer, 
    transport (TCP/UDP) layer and application layer. 
    The interface layer is a key layer in the TCP/IP system that provides an 
    abstracted interface that is not dependent on the link (communication 
    line: frame relay or Ethernet, etc.) to the IP module (IP layer). This means 
    that the IP module can use this abstracted interface (which is not 
    dependent on the link type) to exchange IP packets back and forth with 
    the link layer. 
    The options available in the TCP/IP (IPv4) settings are as follows:
    • DHCP (DHCP setting)
    • Auto-IP (Auto-IP setting)
    • IP Address (IP address setting)
    • Subnet Mask (Subnet mask setting)
    • Gateway (Gateway setting)
    • Bonjour (Bonjour setting)
    IMPORTANT   The DHCP, IP address, subnet mask, gateway and 
    Bonjour menu options for TCP/IP are displayed when TCP/IP is en-
    abled.
    1Press  Z while Network >  is displayed.
    Note  Check with your network administrator when selecting the 
    network setting.
    After all network related settings have been done, turn the 
    machine OFF and ON again. This is mandatory to make the 
    settings effective!
    When COMMAND CENTER is used, network parameters and 
    security settings can be conveniently changed and checked from 
    your PC. For more information, refer to the  COMMAND CENTER 
    Operation Guide .
    Network >
    Downloaded From ManualsPrinter.com Manuals 
    						
    							4-47Using the Operation Panel
    2Press 
    U or  V repeatedly until  >TCP/IP > appears.
    3Press [OK]. A blinking question mark ( ?) appears.
    4Select  On or  Off using  U or  V.
    5Select  On and press  [OK]. Configure the settings shown below.
    DHCP (DHCP setting)
    DHCP (Dynamic Host Configuration Protocol) is the protocol that assigns 
    the information required to establish a network connection when a host 
    attempts to connect to the network (Internet). This information includes 
    the IP address of the local node and the default router (the router in the 
    hosts own network system) and the DNS (Domain Name System) server. 
    DHCP is an extension of the BOOTP (Bootstrap) startup protocol.
    1Press  Z while >TCP/IP  On >  is displayed.
    2Press U or  V repeatedly until  >>DHCP appears.
    3Press [OK]. A blinking question mark ( ?) appears.
    4Select  On or  Off using  U or  V.
    5Press  [OK].
    6Press [MENU] . The display returns to Ready .
    Auto-IP (Auto-IP setting)
    This protocol is used for automatic assignment of an IP address when you 
    connect to a small network that does not have a DHCP server. Select an 
    address from the range 169.254.0.1 to 169.254.255.254, and if no other 
    device on the network is using that address, it is used as your address.
    1Press Z while >TCP/IP  On >  or >TCP/IP  Off >  is displayed.
    2Press U or  V repeatedly until  >>Auto-IP appears.
    3Press [OK]. A blinking question mark ( ?) appears.
    4Select  On or  Off using  U or  V.
    5Press  [OK].
    6Press [MENU] . The display returns to Ready .
    IP Address (IP address setting)
    An IP address is the address of a network device such as a computer and 
    is included in IP packets as needed for the sending and receiving of 
    Internet data (IP packets). (IP addresses can be either destination 
    addresses or source addresses.)
    Specifically, an IP address is a bit string consisting of a host address (or 
    host section) that identifies a computer (host) connected to the Internet 
    and a network address (or network section) that identifies the network to 
    which that computer belongs (or more specifically, the computers 
    >TCP/IP>
    ?Off
    >>DHCP
    ?Off
    >>Auto-IP
    ?Off
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Using the Operation Panel
    4-48
    network interface). Bit strings (IP addresses) that are unique throughout 
    the entire Internet system are allocated to each computer or interface. 
    The IP addresses currently used on the Internet (IPv4) have a fixed length 
    of 32 bits.
    1Press  Z while >TCP/IP  On >  is displayed.
    2Press U or  V repeatedly until  >>IP Address appears.
    3Press [OK]. A blinking cursor ( _) appears.
    4Press  U or V  to increase or decrease, respectively, the value at the 
    blinking cursor. You can set any value between  000 and 255. Use Y 
    and Z  to move the cursor right and left.
    5Display the desired IP address and press [OK] .
    6Press [MENU] . The display returns to Ready .
    Subnet Mask (Subnet mask setting)
    The subnet mask is a way of augmenting the network address section of 
    an IP address. 
    A subnet mask represents all network address sections as 1 and all host 
    address sections as 0. The number of bits in the prefix indicates the 
    length of the network address. The term prefix refers to something 
    added to the beginning and, in this context, indicates the first section of 
    the IP address. 
    When an IP address is written, the length of the network address can 
    indicated by the prefix length after a forward slash (/). For example, 24 
    in the address 133.210.2.0/24. In this way, 133.210.2.0/24 denotes 
    the IP address 133.210.2.0 with a 24-bit prefix (network section). 
    This new network address section (originally part of the host address) 
    made possible by the subnet mask is referred to as the subnet address.
    1Press Z while >TCP/IP  On >  is displayed.
    2Press U or  V repeatedly until  >>Subnet Mask  appears.
    3Press [OK]. A blinking cursor ( _) appears.
    4Press  U or V  to increase or decrease, respectively, the value at the 
    blinking cursor. You can set any value between  000 and 255. Use Y 
    and Z  to move the cursor right and left.
    5Display the desired subnet mask and press  [OK].
    6Press  [MENU] . The display returns to Ready .
    Note  When you enter the IP address, be sure to set the  DHCP 
    setting to Off.
    >>IP Address
    000.000.000.000
    Note  When you enter the subnet mask, be sure to set the  DHCP 
    setting to Off.
    >>Subnet Mask
    000.000.000.000
    Downloaded From ManualsPrinter.com Manuals 
    						
    							4-49Using the Operation Panel
    Gateway (Gateway setting)
    Gateway generally refers to a protocol conversion device used to allow 
    networks with differing protocol systems to interconnect. 
    For example, a Gateway device is required to connect a different closed 
    network (using its own protocols) to the open Internet (using TCP/IP). 
    By installing a gateway, the communications protocols and data display 
    modes on different networks can be made compatible.
    On TCP/IP networks, the term gateway is used to refer to routers.
    1Press 
    Z while >TCP/IP  On >  is displayed.
    2Press U or  V repeatedly until  >>Gateway appears.
    3Press [OK]. A blinking cursor ( _) appears.
    4Press  U or V  to increase or decrease, respectively, the value at the 
    blinking cursor.  You can set any value between  000 and  255. Use  Y 
    and Z  to move the cursor right and left.
    5Display the desired gateway and press  [OK].
    6Press  [MENU] . The display returns to Ready .
    Bonjour (Bonjour setting)
    Bonjour, also known as zero-configuration networking, is a service that 
    automatically detects computers, devices and services on an IP network. 
    Bonjour, because an industry-standard IP protocol is used, allows 
    devices to automatically recognize each other without an IP address 
    being specified or DNS server being set. 
    Bonjour also sends and receives network packets by UDP port 5353. If a 
    firewall is enabled, the user must check that UDP port 5353 is left open 
    so that Bonjour will run correctly. Some firewalls are set up so as to reject 
    only certain Bonjour packets. If Bonjour does not run stably, check the 
    firewall settings and ensure that Bonjour is registered on the exceptions 
    list and that Bonjour packets are accepted. If you install Bonjour on 
    Windows XP Service Pack 2 or later, the Windows firewall will be set up 
    correctly for Bonjour.
    1Press Z while >TCP/IP  On >  is displayed.
    2Press U or  V repeatedly until  >>Bonjour appears.
    3Press [OK]. A blinking cursor ( _) appears.
    4Select  On or  Off using  U or  V.
    5Press  [OK].
    6Press [MENU] . The display returns to Ready .
    Note  Before you input the gateway, be sure to set the  DHCP 
    setting to Off.
    >>Gateway
    000.000.000.000
    >>Bonjour
    ? Off
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Using the Operation Panel
    4-50
    TCP/IP (IPv6) (IPv6 settings)
    This selects the settings for TCP/IP (IPv6).
    TCP/IP (IPv6) is based on the current  Internet protocol, TCP/IP (IPv4). 
    IPv6 is the next-generation Internet protocol and expands the available 
    address space, which resolves the problem of the lack of addresses 
    under IPv4, while also introducing other improvements such as additional 
    security functionality and the capacity to prioritize data transmission. 
    The options available in the TCP/IP (IPv6) settings are as follows:
    • RA (Stateless) (RA (Stateless) setting)
    • DHCPv6 (DHCPv6 setting)
    IMPORTANT   The RA (Stateless) and DHCPv6 menu options for TCP/
    IP (IPv6) are displayed when TCP/IP (IPv6) is enabled.
    1Press  Z while Network >  is displayed.
    2Press U or  V repeatedly until  >TCP/IP (IPv6) >  appears.
    3Press [OK]. A blinking question mark ( ?) appears.
    4Select  On or  Off using  U or  V.
    5Select  On and press  [OK]. Configure the settings shown below.
    RA (Stateless) (RA (Stateless) setting)
    The IPv6 router communicates (transmi ts) information such as the global 
    address prefix using ICMPv6. This information is the Router 
    Advertisement (RA).
    ICMPv6 stands for Internet Control Message Protocol, and is a IPv6 
    standard defined in the RFC 2463 Internet Control Message Protocol 
    (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification.
    1Press  Z while >TCP/IP (IPv6)  On >  is displayed.
    2Press U or  V repeatedly until  >>RA(Stateless)  appears.
    3Press [OK]. A blinking question mark ( ?) appears.
    4Select  On or  Off using  U or  V.
    5Press  [OK].
    6Press [MENU] . The display returns to Ready .
    DHCPv6 (DHCPv6 setting)
    DHCPv6 is the next-generation of the Internets Dynamic Host 
    Configuration Protocol and supports IP v6. It extends the BOOTP startup 
    protocol that defines the protocols used for transferring configuration 
    information to hosts on the network. 
    DHCPv6 permits the DHCP server to use its expanded functionality to 
    send configuration parameters to an IPv6 node. Because the network 
    addresses that can be used are allocated automatically, the IPv6 node 
    management workload is reduced in systems where the administrator 
    has to exercise close control over IP address allocation.
    >TCP/IP (IPv6) >
    ? Off
    >>RA(Stateless)
    ? Off
    Downloaded From ManualsPrinter.com Manuals 
    						
    							4-51Using the Operation Panel
    1Press 
    Z while >TCP/IP (IPv6)  On >  is displayed.
    2Press U or  V repeatedly until  >>DHCPv6 appears.
    3Press [OK]. A blinking question mark ( ?) appears.
    4Select  On or  Off using  U or  V.
    5Press  [OK].
    6Press [MENU] . The display returns to Ready .
    >>DHCPv6
    ? Off
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Using the Operation Panel
    4-52
    Device Common (Selecting/Setting the common 
    device)
    Selects/sets all the functions in this printer.
    The options available in Device Common are as follows:
    • Message Language (Selecting the message language)
    • Date Setting (Date and time settings)
    • Buzzer (Alarm (Buzzer) setting)
    • RAM Disk Mode (Using the RAM disk)
    • Hard Disk (Using the optional hard disk)
    • Error Handling (Error  detection setting)
    • Timer (Timer setting)
    1Press  [MENU] .
    2Press U or  V repeatedly until  Device Common >  appears.
    Message Language (Selecting the message language)
    You can select the language of the message display by following the 
    procedure given below
    . You can optionally download messages in other 
    languages. Contact your service technician for information.
    1Press  Z while Device Common >  is displayed.
    2Press U or  V repeatedly until  >Message Language  appears. The 
    default message language is  English.
    3To change the language, press  [OK]. A blinking question mark (? ) 
    appears.
    4Press  U or  V. The display cycles through the available selection in 
    the following order:
    English
    Français
    Deutsch
    Italiano
    Nederlands
    Español
    Русский
    Português
    5Press  [OK].
    6Press [MENU] . The display returns to Ready .
    Date Setting (Date and time settings)
    Set the date and time.
    The date and time settings consist of the following items:
    • Date (date setting)
    • Time (time setting)
    • Date Format (date format selection)
    1Press Z while Device Common >  is displayed.
    Device Common >
    >Message Language
    ? English
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Kyocera manuals Comments (0)

    Related Manuals for Kyocera FS C5250DN User Manual