Kyocera FS 3140MFP User Manual

2
Preparation before Use
2-5
Connecting Cables 
Follow the steps below to connect cables to the machine.
1Turn the main power switch off (O).
2Connect the machine to the PC or your network device. 
When using the network interface, remove the cap.
When connecting the network cable, configure the 
network. For details, refer to Network Setup (LAN Cable 
Connection) on page 2-14 .
3Connect one end of the supplied power cable to the 
machine and the other end to a power outlet.
IMPORTANT: Only use the power...

Preparation before Use
2-6
Power On/Off
Power On
When the main power indicator is lit... Press the Power key.
When the main power indicator is off... Turn the main power switch on.
IMPORTANT: When turning off the main power swit ch, do not turn on the main power switch again immediately. Wait 
more than 5 seconds, and then turn on the main power switch.
Downloaded From ManualsPrinter.com Manuals 

2
Preparation before Use
2-7
Power Off
Before turning off the main  power switch, press the Power key on the operation panel to off. Make sure that the 
memory  indicator is off before turn ing off the main power switch.
In case of not using the machine for a extended period of time
CAUTION: If this machine will be left unused fo r an extended period (e.g. overnight), turn it of f at the main 
power switch. If the machine will not be  used for an even longer period of time (e.g. vacation), remove the...

Preparation before Use
2-8
Auto Low Power Mode
Auto Low Power Mode automatically  switches the machine into Low Power Mode if  left idle for 2 minutes.
Sleep and Auto Sleep
Sleep
To enter Sleep, press the Power key. Message Display and 
all indicators on the operatio n panel will go out to save a 
maximum amount of power except the Main Power indicator. 
This status is referred to as Sleep.
If print data is received during Sleep, the print job is 
performed while the Messag e Display remains unlit.
If...

2
Preparation before Use
2-9
Switching the Language  for Display [Language] 
Select the language displayed on the Message Display.
Use the procedure below to select the language.
1Turn on the main power switch.
2Press the System Menu/Counter  key on the main unit 
operation panel.
When you are performing user management and have 
not logged in, a login scre en will appear. Then, enter the 
user ID and password to log in.
NOTE: The following administrator is registered in the 
machine at the factory....

Preparation before Use
2-10
6Press the OK  key. Language appears.
7Press the U or  V key to select the desired language and 
then press the  OK key.
Completed.  is displayed and the screen returns to the 
Common Settings menu.
Language:a  b 
*********************
2  Deutsch
3  Français
1 *English
Downloaded From ManualsPrinter.com Manuals 

2
Preparation before Use
2-11
Setting Date and Time
Follow the steps below to set the local date  and time at the place of installation.
When you send an E-mail using the transmis sion function, the date and time as set here will  be printed in the header 
of the E-mail message. Set the date, time and time diff erence from GMT of the region where the machine is used.
NOTE: Be sure to set the time difference before setting the date and time.
1Press the System Menu/Counter key on the main unit 
operation...

Preparation before Use
2-12
8Press the OK  key. Time Zone appears.
9Press the U or V key to select your  region and then 
press the  OK key.
Completed.  is displayed and the screen returns to the 
Date Setting menu.
10Press the U  or V key to select [Summer Time].
11Press the OK  key. Summer Time appears.
12Press the U or V key to select [On] or [Off] and then 
press the  OK key.
Completed.  is displayed and the screen returns to the 
Date Setting menu.
13Press the U  or V key to select [Date/Time]....

2
Preparation before Use
2-13
16Press the Y or  Z key to move the cursor position, press 
the  U or  V key to enter hours, minutes and seconds, 
and then press the  OK key.
Completed.  is displayed and the screen returns to the 
Date Setting menu.
17Press the U  or V key to select [Date Format].
18Press the OK  key. Date Format appears.
19Press the U or V key to select the desired display 
format and then press the  OK key.
Completed.  is displayed and the screen returns to the 
Date Setting menu....

Preparation before Use
2-14
Network Setup (LAN Cable Connection)
The machine is equipped with network in terface, which is compatible with network protocols such as TCP/IP (IPv4), 
TCP/IP (IPv6), IPX/SPX, NetBEUI, IPSec, and AppleTalk. It enables network  printing on the Windows, Macintosh, 
UNIX, NetWare and other platforms.
The table below shows the items required for each of the settings. 
Configure the printers network parameters as appr opriate for your PC and your network environment. 
For details...