Kyocera FS 2020DN User Manual

7-34Using the Operation Panel
Print Settings
These settings specify printing parameters such as the print quality used 
for printing (Normal or Fine), the gloss mode (Low or High), the number 
of copies, reduced printing and the page orientation. 
The options available in Print Quality are as follows:
•Paper Source (Selecting the paper feed source)
• Paper Feed Mode (Setting the paper feed source)
• Duplex (Duplex Printing)
• Paper Output (Selecting the output stack)
• Override A4/LT (Overriding...

Using the Operation Panel7-35
Paper Feed Mode (Setting the paper feed source)
This mode specifies how the paper should be fed, after the paper feed 
source and paper type has been chosen. If  Auto is selected, the printer 
searches for a paper feed source that matches the paper size and type, 
and paper is delivered from that source. An error message is displayed if 
Fixed  is selected, but a match is not found. The default setting is  Auto. 
To change the settings, follow the steps described below....

7-36Using the Operation Panel
Duplex (Duplex printing)
Using the duplexer, you can automatically print on both sides of the 
paper. The duplexer is mounted underneath the printer.
Duplex printing is available for the following paper types:
PLAIN
PREPRINTED
BOND
RECYCLED
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
HIGH QUALITY
CUSTOM 1  (to 8)
Activating the duplexer is done by  selecting either short edge or long 
edge binding mode.
Binding Modes
Binding refers to the manner in which printed pages of paper are...

Using the Operation Panel7-37
4Press U or  V to display the desired binding mode. The message 
display toggles through the following:
Off (default)
Short edge bind
Long edge bind
5Press  [OK].
6Press  [MENU] . The display returns to  Ready.
Paper Output (Selecting the output stack)
The Paper Output menu on the operation panel allows you to select 
either the face-down tray or the faceup tray option for the output stack.
1Press Z while  Print Settings >  is displayed.
2Press U or  V repeatedly until...

7-38Using the Operation Panel
2Press U or  V repeatedly until  >Emulation > appears on the 
message display. One of the emulation modes appears, indicating 
the emulation currently in use.
3Press  [OK]. A blinking question mark ( ?) appears.
4Press  U or  V repeatedly until the desired emulation mode is 
displayed.
PCL 6
KPDL
KPDL (AUTO) (default)
Line Printer
IBM Proprinter
DIABLO 630
EPSON LQ-850
5Press  [OK]. 
6Press  [MENU] . The display returns to  Ready.
Alternative Emulation for KPDL Emulation...

Using the Operation Panel7-39
Error Report (Printing KPDL errors)
The printer can print error descriptions when printing error occurs during 
KPDL emulation. The default is  On — the printer prints KPDL errors.
1Press  Z while  Print Settings >  is displayed.
2Press U or  V repeatedly until  >Emulation > appears.
3Press [OK]. A blinking question mark ( ?) appears.
4Select  KPDL or KPDL (AUTO)  using U or  V. Press  [OK].
5Press  Z. >>Error Report  appears.
6Press [OK]. A blinking question mark ( ?)...

7-40Using the Operation Panel
5Press U or  V repeatedly until the desired font number appears. For 
font numbers of the internal fonts, refer to  Print Fonts List on page7-
15 .
6When the desired font is displayed, press  [OK].
7Press  [MENU] . The display returns to  Ready.
Selecting Regular or Dark  Courier/Letter Gothic
Courier or Letter Gothic font thickness can be selected as  Regular or 
Dark . In the procedure below, it is assumed that Courier is selected. The 
procedure is the same for Letter...

Using the Operation Panel7-41
Character Pitch
You can set the character pitch for fixed fonts.
1Press Z while  Print Settings >  is displayed.
2Press U or  V repeatedly until  >Font Select  >  appears.
3Make sure that  Internal is displayed and press  Z.
4Press  U or  V repeatedly until  >>Pitch appears.
5Press [OK]. A blinking question mark ( ?) appears.
6Press  U or  V to increase or decrease the value at the blinking 
cursor. The character pitch can be set 0.44 and 99.99 characters per 
inch, in 0.01...

7-42Using the Operation Panel
Print Quality (Setting print quality)
In Print Quality menus, you can set the KIR mode, EcoPrint mode, and 
other settings.
The options available in Print Quality are as follows:
•KIR Mode (Selecting the KIR mode)
• EcoPrint Mode (Selecting the EcoPrint mode)
• Resolution (Selecting the Print Resolution)
• Print Density (Selecting the Print Density)
1Press  Z while  Print Settings >  is displayed.
2Press U or  V repeatedly until  >Print Quality >  appears.
KIR Mode...

Using the Operation Panel7-43
EcoPrint Mode (Selecting the EcoPrint mode)
By enabling EcoPrint mode, you can minimize the amount of toner used 
during printing. Because images printed in this mode may be slightly 
coarser than those printed in standard resolution, you should use 
EcoPrint for test prints or other situations where high-quality prints are 
not required.
Use the procedure below to select EcoPrint mode. The default setting is 
Off.
1Press  Z while  >Print Quality >  is displayed.
2Press U...