Kyocera FS 2000D User Manual

2F8/2F9/2GA-1
1-3-15 Service items Description
No.ItemsDescription
(10)
cont.(b) Detail of jam location
Paper
feeder 1 Output
tray
Paper
feeder 2
Paper
feeder 3(Cassette 1)
(Cassette 2)
(Cassette 3)
(Cassette 4)Printer
42
31
31
4A
32
32
49
4748
33
34
(MP tray)Envelope
feeder
Bulk feeder
(Fuser)
(Fuser)(Fuser)(Inside the printer)(Inside the printer)(Inside the printer)
(Rear unit)
(Rear unit)(Rear unit)
(Duplex conveying)
(Duplex conveying)(Duplex conveying)
1
5
7
6
8
3
24(Face down tray)
(Face down...

2F8/2F9/2GA-4
1-3-16Service items Description
No.ItemsDescription
(10)
cont.(c) Detail of paper source (Hexadecimal)
00: MP tray
01: Paper cassette 1 (printer)
02: Paper cassette 2 (paper feeder 1)
03: Paper cassette 3 (paper feeder 2)
04: Paper cassette 4 (paper feeder 3)
05: Reserved06: Reserved
07: Reserved
08: Bulk paper feeder
09; Envelope feeder
(d) Detail of paper size (Hexadecimal)
01: Monarch
02: Business 
03: International DL
04: International C5
05: Executive 
06: Letter-R
86: Letter-E
07:...

2F8/2F9/2GA-4
1-3-17 Service items Description
No.ItemsDescription
(12)Maintenance Log
NOTE:
It is not logged if 
100 or more counts 
are not added to the 
count at the last 
occurrence of 
replacement.#Count.Item
Remembers 1 to 8 of 
occurrence of replacement. 
If the occurrence of the pre-
vious replacement of toner 
container is less than 8, all 
of the occurrences of 
replacement are logged.The total page count at 
the time of the replace-
ment of the toner con-
tainer.
This is virtually logged as...

2F8/2F9/2GA-3
1-3-18Setting the paper feed operation (printer driver priority mode)
Description
With printer driver priority mode, when selecting the specific paper feed location (a cassette 
or MP tray) with the printer driver (it is not automatic selection), paper is fed from the 
selected location. Message Add Paper is displayed when there is no paper in that location.
When selecting the MP tray as the paper feed location, paper is fed with the timing of maxi-
mum size (A4). As for the setting media...

2F8/2F9/2GA
1-3-19 Initializing the developer unit (toner install mode)
Description
The new developer unit is shipped from the factory with no toner contained. The developer 
can be automatically replete with toner when a toner container is installed onto it and the 
printer is turned on. However, because the toner reservoir in the developer has a large 
capacity, it requires a lengthy period of time until a substantial amount of toner has been fed 
to get the printer ready. (A new developer needs...

2F8/2F9/2GA
1-3-20Drum surface refreshing
Description
Rotates the drum approximately 3 minutes with toner lightly on the overall drum using the 
high-voltage output control of the engine PWB. The cleaning blade in the drum unit scrapes 
toner off the drum surface to clean it.
Purpose
To clean the drum surface when image failure occurs due to the drum. This mode is effective 
when dew condensation on the drum occurs.
Method
1. Enter the service mode [>>Drum].
2. Press the OK key. [>>Drum?] will be...

2F8/2F9/2GA-1
1-4-1
1-4 Troubleshooting1-4-1  Paper misfeed detection
(1) Paper misfeed indication
When a paper misfeed occurs, the printer immediately stops printing and displays the paper misfeed message on the 
operation panel. To remove paper misfed in the printer, pull out the paper cassette, pull out the rear unit, remove the devel-
oper unit or open the duplex cover.
Figure 1-4-1
(2) Paper misfeed detection
Figure 1-4-2
Paper Jam
MP tray
Paper misfeed locationPaper misfeed message
Face down tray...

2F8/2F9/2GA-1
1-4-2
1-4-2  Self-diagnostic function
(1) Self-diagnostic function
This printer is equipped with self-diagnostic function. When a problem is detected, the printer stops printing and display an 
error message on the operation panel. An error message consists of a message prompting a contact to service personnel,
total print count, and a four-digit error code indicating the type of the error. (The display varies depending on the type of 
the error.)
(2) Self diagnostic codes
Code...

2F8/2F9/2GA-1
1-4-3 1140 Lift motor ascent error
*35/37 and 45/47 ppm printers (EUR/
USA model) only
Optional bulk paper feeder’s tray top 
position sensor does not turn on.
Lift motor lock error occurred 3 times.Defective bulk 
paper feeder’s tray 
top position sensor.Replace the bulk paper feeder’s tray top 
position sensor.
Defective harness 
between bulk 
paper feeder’s tray 
top position sen-
sor and main PWB 
(YC6), or improper 
connector inser-
tion.Reinsert the connector. Also check for conti-...

2F8/2F9/2GA
1-4-42200 Drum motor error
DMOTRDYN signal does not go low 
within 2 s after DMOTONN signal goes 
low.Defective harness 
between drum 
motor and engine 
PWB (YC11), or 
improper connec-
tor insertion.Reinsert the connector. Also check for conti-
nuity within the connector harness. If none, 
remedy or replace the harness.
Defective drum 
motor drive 
transmission 
system.Check if the gears rotate smoothly. If not, 
grease the bushings and gears. Check for 
broken gears and replace if any....