Kyocera FS 2000D User Manual

2F8/2F9/2GA-4
1-2-3 Figure 1-2-2 Unpacking
Unpacking.
 

 






 
 


	
 


30/31 ppm printer
35/37 ppm printer
45/47 ppm printer
1. Printer
2. Outer case
3. Bottom pad L
4. Bottom pad R
5. Machine cover
6. Top pad L
7. Top pad R
8. Accessory spacer
9. Plastic bag10. Installation guide etc.
11. Plastic bag
12. Toner container
13. Power cord
14. Waste toner box
15. Leaflet
 (30/35/45 ppm printer 
[EUR model] only)
16. Cassette lid
Downloaded From ManualsPrinter.com Manuals 

2F8/2F9/2GA-2
1-2-41. Attach the included language label sheet on 
the indicator as shown in the figure.
Figure 1-2-3
Attaching the label.
Ready
PAR A4 PLAIN
Language label sheet
Downloaded From ManualsPrinter.com Manuals 

2F8/2F9/2GA
1-2-5 1. Open the top cover.
2. Remove the tape.
Figure 1-2-4
Installing the toner container and waste toner box.
Top cover
Tape
Downloaded From ManualsPrinter.com Manuals 

2F8/2F9/2GA
1-2-63. Shake the new toner container at least 10 
times as shown in the figure in order to dis-
tribute the toner evenly inside the container.
4. Carefully remove the protective seal (orange 
colored).
Figure 1-2-5
5. Install the toner container into the printer. 
6. Push on the PUSH HERE marks on the 
toner container until the container clicks into 
place.
7. Close the top cover.
Figure 1-2-6
8. Open the cap of the waste toner box.
9. Open the left side cover.
10. Insert the new waste toner...

2F8/2F9/2GA-1
1-2-7 1. Pull out the paper cassette.
2. Push the bottom plate down until it locks 
(30/31 ppm printer [EUR/USA model] only).
Figure 1-2-8
3. Turn the paper size dial so that the size of 
the paper you are going to use appears in 
the paper size window.
Figure 1-2-9
Adding paper to the paper cassette.
Bottom plate
Paper cassette
Paper size dial
Paper size window
Downloaded From ManualsPrinter.com Manuals 

2F8/2F9/2GA
1-2-84. Pull the release lever on the left side guide 
and slide to the desired paper size.
Figure 1-2-10
5. Pull the release lever and slide the paper 
stopper to the desired paper size.
When using non-standard size paper, move 
the paper guides and paper stopper all the 
way out, insert the paper, then adjust the 
paper guides and paper stopper to the size 
of the paper. Adjust them so that they are in 
light contact with the paper.
6. Insert the paper cassette into the slot in the...

2F8/2F9/2GA
1-2-9 1. Install the cassette lid.
Figure 1-2-12
Installing the casette lid.
Cassette lid
Cassette lid
Downloaded From ManualsPrinter.com Manuals 

2F8/2F9/2GA-2
1-2-101. Connect the printer cable (parallel, USB or 
network*) to the printer and the PC.
*: Remove the cap.
Figure 1-2-13
1. Connect the power cord to the printer’s AC 
inlet and the other end into a power outlet.
2. Turn the power switch to on ( | ).
The message display should indicate [Self 
test]. When the printer is first switched on 
after installation, there will be a delay of 
approximately 15 minutes before the printer 
gets ready to print as the developer needs to 
be filled with...

2F8/2F9/2GA
1-2-11 1. Press the Menu key when [Ready] is dis-
played.
2. Press T or S key to display [Print Status 
Page].
3. Press OK key to display [Print Status 
Page?].
4. Press OK key. [Processing] will be displayed 
and the status page will be printed. When 
printing is complete, [Ready] will appear 
again.
5. Check to see if the status page is properly 
printed.
1. Switch on the PC and activate Windows.
 If the Welcome to the Found New Hardware 
Wizard dialog box displays, select [Cancel].
2....

2F8/2F9/2GA
1-2-12
1-2-3  Installing the expanding memory (optional)

1. Power off the printer and unplug the printer 
power cord.
2. Open the right side cover.
3. Remove the screw and open the inner 
cover.
Figure 1-2-15
4. Push out the clamps on both ends of the 
memory socket.
5. Remove the memory from its package. 
Aligning the cutouts of the memory with the 
matching keys of the socket, carefully plug 
the memory into the memory socket until it 
clicks in place.
6. Push the two socket clamps to...