Kyocera FS 2000D User Manual

2F8/2F9/2GA-2
1-5-29 5. Remove the eight screws and three ground-
ing terminals.
Figure 1-5-39
6. Remove the AC inlet.
7. Remove the one connector.
8. Remove the PWB connector between con-
nect-L PWB and then remove the power 
source unit.
9. Remove the power source unit.
10. Check or replace the power source unit and 
refit all the removed parts.
Figure 1-5-40
Screw
Screw
Screw
Screw ScrewScrew Screw Screw
Grounding
terminal Grounding
terminal Grounding
terminal
PWB connector
Connect-L PWB
Connector...

2F8/2F9/2GA-2
1-5-30
1-5-9  Others
(1) Detaching and refitting the paper feed drive unit
Procedure
1. Remove the paper cassette.
2. Remove the developer unit (See page P.1-5-
9).
3. Remove the top cover (See page P.1-5-2).
4. Remove the right cover (See page P.1-5-3).
5. Remove the five connectors from the con-
nect-R PWB.
6. Remove wires from the clamp.
7. While opening the four hooks and then 
remove the wires.
8. Remove the right fan motor.
Figure 1-5-41
9. Remove the three screws and then remove 
the...

2F8/2F9/2GA
1-5-31 (2) Detaching and refitting the main drive unit
Procedure
1. Remove the top cover (See page P.1-5-2).
2. Remove the right cover (See page P.1-5-3).
3. Remove the controller box (See page P.1-5-
26).
4. Remove five screws and then remove the 
main drive unit.
5. Check or replace the main drive unit and 
refit all the removed parts.
Figure 1-5-43
Screw
ScrewScrew
Screw
ScrewMain drive unit
Downloaded From ManualsPrinter.com Manuals 

2F8/2F9/2GA-1
1-5-32 (3) Detaching and refitting the laser scanner unit
Procedure
1. Remove the top cover (See page P.1-5-2).
2. Remove the right cover (See page P.1-5-3).
3. Remove the three/four connectors from the 
main PWB.
4. Remove the four screws and then remove 
the laser scanner unit.
5. Check or replace the laser scanner unit and 
refit all the removed parts.
Figure 1-5-44
Screw
Screw
Laser scanner unit
Connectors (three/four)
45/47 ppm printer
(EUR/USA model)
only Screw Screw
45/47 ppm...

2F8/2F9/2GA-1
1-6-1
1-6 Firmware1-6-1  Downloading firmware
The system firmware can be update by downloading new firmware. Downloading can be made either by directly sending 
the new firmware from PC via the parallel interface or using a memory card that contains the new firmware.
Figure 1-6-1
S2F8_1000001021.cmp
Firmware file name example
Product code
2F8: 30/31 ppm printer (EUR/USA model)
2F9: 35/37 ppm printer (EUR/USA model)
2GA: 45/47 ppm printer (EUR/USA model)
Pause (under bar)Pause (period)
Build...

2F8/2F9/2GA-1
1-6-2 (1) Downloading the firmware from the parallel interface
To download the system firmware using the parallel interface, use the procedure below.
Note that you can’t download both the system and engine firmware at a time.
1. Turn printer and PC power off.
2. Connect the parallel printer cable between 
the PC and the printer.
Figure 1-6-2
3. Turn printer power on.
4. Confirm that display (1) is displayed.
5. At the DOS prompt, enter command (2).
* Enter UPGR “SYS” in capitals.
6. Confirm...

2F8/2F9/2GA-4
1-6-3 (2) Downloading the firmware from the memory card
The procedure below provides how to download firmware from a memory card.
Note that you can download both the system and engine firmware at a time.
1. Turn printer power off.
2. Remove two screws and then remove the 
interface slot cover.
3. Insert the memory card into the printers 
memory card slot.
Figure 1-6-4
4. Turn printer power on.
5. Press Menu key on the printers operation 
panel and carry out the memory card for-
matting...

2F8/2F9/2GA-1
1-6-411. Confirm that the printers power switch is set 
to off.
12. Insert the memory card into the printers 
memory card slot.
Figure 1-6-7
13. Turn printer power on.
14. When message display (1) is displayed to 
detect firmware in the memory card.
15. Message display (2) is displayed during 
downloading.
16. When message display (3) is displayed to 
indicate downloading is finished.
17. Turn printer power off.
18. Remove the memory card from memory 
card slot.
19. Turn printer power on....

2F8/2F9/2GA-2
1-6-5 (3) Downloading the firmware from the USB memory
The procedure below provides how to download firmware from a memory card.
Note that you can’t download both the system and engine firmware at a time.
1. Turn printer power off.
2. Connect the USB memory to the PC.
3. Copy the firmware file to the root directory of 
the USB memory.
4. Remove the USB memory from the PC and 
then insert the USB memory into the 
printers USB memory slot.
Figure 1-6-9
5. Turn printer power on.
6. When...

2F8/2F9/2GA
1-6-6This page is intentionally left blank.
Downloaded From ManualsPrinter.com Manuals