Kyocera FS 1350DN User Manual

							4-6Connecting and Printing
TCP/IP (IPv6)
This section describes how to enable the TCP/IP (IPv6) protocol.
1If TCP/IP (IPv6) is set to Off, use U or V to select On and press  
[OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question 
mark (?) appears while you are setting RA(Stateless) and 
DHCPv6.
4Press U or V to select On or Off as the setting for 
RA(Stateless) and DHCPv6.
5Press [OK].
6Press [MENU]. The display returns to Ready.
NetWare, AppleTalk, IPP, SSL Server, IPSec and 
Security Level settings
1
Press [MENU].
2Press U or V repeatedly until Security > appears.
NoteCheck with your network administrator for the network 
address settings. 
>TCP/IP (IPv6) >
  On
>>DHCPv6
  Off
>>RA(Stateless)
  Off
>>DHCPv6
 ?Off
>>RA(Stateless)
 ?Off
Security       >
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing4-7
3Press Z. Each time you press U or V, the selection changes. Refer 
to the explanations below when specifying the settings.
If you are using NetWare, AppleTalk, IPP, SSL Server or 
IPSec to connect to a network, you must enter an administrator ID 
and press [OK]. By default, the administrator ID is the numeric part 
of your printers model name  1350. 
If you are using NetWare, AppleTalk, IPP, SSL Server or 
IPSec to connect to a network, you must enter an administrator 
password and press [OK]. By default, the administrator password is 
the numeric part of your printers model name 1350.
Set this item to On when you connect to a network using NetWare. 
In submenu, frame mode can be selected from Auto, 802.3, 
Ethernet-II, SNAP and 802.2.
AppleTalk must be activated (On) for networking with Macintosh 
computers.
Set this item to On when you connect to a network using IPP.
Set this item to On when you connect to a network using SSL 
Server. Submenu has items including DES, 3DES, AES, IPP over 
SSL and HTTPS.
Set this item to On when you connect to a network using 
IPSec.
Continued on next page.
ID
_
Password
_
>NetWare       >
  On
>AppleTalk
  On
>IPP
  Off
>SSL Server
  Off
>IPSec
  Off
Downloaded From ManualsPrinter.com Manuals 
						

							4-8Connecting and Printing
Set the Security Level to High.
NetWare
This section explains the procedure for enabling NetWare.
1Enter the administrator ID and password. Then, if NetWare is set to 
Off, use U or V to select On and press [OK].
2Press Z.
3Press [OK]. A blinking question mark (?) appears. Each time you 
press U or V, the selection changes.
4Display the item you want to set and press [OK].
5Press [MENU]. The display returns to Ready.
>Security Level
 
High
>NetWare       >
  On
>>Frame Type
  Auto
>>Frame Type
 ?802.3
>>Frame Type
 ?Ethernet-II
>>Frame Type
 ?802.2
>>Frame Type
 ?SNAP
>>Frame Type
 ?Auto
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing4-9
AppleTalk
This section explains the procedure for enabling AppleTalk. 
1Enter the administrator ID and password. Then, if AppleTalk is set 
to Off, use U or V to select On.
2Press [OK]. A blinking question mark (?) appears.
3Press [OK] again.
4Press [MENU]. The display returns to Ready.
IPP
This section explains the procedure for enabling IPP. 
1Enter the administrator ID and password. Then, if IPP is set to Off, 
use U or V to select On.
2Press [OK]. A blinking question mark (?) appears.
3Press [OK] again.
4Press [MENU]. The display returns to Ready.
>AppleTalk
  On
>AppleTalk
 ?On
>IPP
  On
>IPP
 ?On
Downloaded From ManualsPrinter.com Manuals 
						

							4-10Connecting and Printing
SSL Server
This section explains the procedure for enabling SSL Server.
1Enter the administrator ID and password. Then, if SSL Server is 
set to Off, use U or V to select On and press [OK].
2Press Z. Each time you press U or V, the selection changes.
3Display the item you want to set and press [OK]. A blinking question 
mark (?) appears.
4Select On or Off using U or V.
5Press [OK].
6Press [MENU]. The display returns to Ready.
IPSec
This section explains the procedure for enabling IPSec.
1Enter the administrator ID and password. Then, if IPSec is set to 
Off, use U or V to select On.
2Press [OK]. A blinking question mark (?) appears.
3Press [OK] again.
4Press [MENU]. The display returns to Ready.
>SSL Server    >
  On
>>3DES
  Off
>>AES
  Off
>>IPP over SSL
  Off
>>HTTPS
  Off
>>DES
  Off
>>DES
 ?Off
>IPSec
  On
>IPSec
 ?On
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing4-11
Security Level
Security Level is primarily a menu used by service representative 
for maintenance work. There is no need for customers to use this menu.
>Security Level
  High
Downloaded From ManualsPrinter.com Manuals 
						

							4-12Connecting and Printing
Printing a Network Interface Status Page
You can print out a status page for the network interface. The network 
status page shows the network addresses, and other information under 
various network protocols about the network interface.
Adjust/Maintenance
Adjust/Maintenance is used to adjust the print quality and to carry out 
printer maintenance.
The options available in Adjust/Maintenance are as follows:
•Restart Printer
•Service
1Press [MENU].
2Press U or V repeatedly until Adjust/Maintenance > appears.
3Press Z while Adjust/Maintenance > is displayed.
4Press U or V repeatedly until >Service > appears.
5Press Z.
6Press U or V repeatedly until >>Print Network Status Page 
appears.
7Press [OK]. A question mark (?) appears.
8Press [OK]. Processing appears and a status page is printed out.
9When printing ends, the display returns to Ready.
IMPORTANTService is primarily a menu used by service 
representative for maintenance work. There is no need for customers 
to use this menu.
Adjust/        >
Maintenance
>>Print Network
 Status Page ?
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing4-13
Installing the Printer Driver
According to the instructions of the Installation Guide, connect the PC to 
the printer and turn on them to install the printer driver. 
For more 
information on printer driver, refer to the KX Driver User Guide in the CD-
ROM.
Installing the Printer Driver on Windows PC
This section explains how to install the printer driver in Windows Vista.
1Ensure the printer is plugged in and connected to the computers 
USB or Network port before installing software from the CD-ROM.
2Insert the CD-ROM (Product Library) into the CD-ROM drive. If the 
AutoPlay screen appears, click Run Setup.exe. The Notice screen 
appears.
3Select View License Agreement to read the information and select 
Accept to proceed.
4Click Install Software. The Installation Method screen appears.
5Select Express Mode or Custom Mode as the installation method.
•Express Mode: If the printer is connected via USB or a network and 
is turned on, the installer detects the printer. Select Express Mode to 
perform a standard installation.
NoteTo install the printer driver, you must log on with 
administrator privilege.
NoteIf a Plug and Play window like that shown at left 
appears, click Cancel. 
NoteIf the installation program fails to launch, use Windows 
Explorer to access the CD-ROM and select Setup.exe. 
NoteIn Windows XP, click Install Software to start the 
Installation wizard. Click Next to display the Installation 
Method screen.
Downloaded From ManualsPrinter.com Manuals 
						

							4-14Connecting and Printing
•Custom Mode: This option allows you to select items to be installed 
as required and to specify the port.
Proceed the section below according to the installation method.
Express Mode
When selecting Express Mode, printer driver and fonts are installed. 
After installing with this mode, the other utilities can be added using 
Custom Mode.
1On the Installation Method screen, click Express Mode. The 
installer searches the connected printers on Discover Printing 
System screen. If no printer is discovered, ensure the printer is 
plugged in and connected to the computers USB or Network port, 
then check Refresh to search printers again.
2Select the printer you want to install, and click Next.
3Confirm the settings and click Install. Printer driver installation 
starts.
4Installation Completed screen appears. Click Finish to return to the 
main menu. 
NoteIf Found New Hardware window appears, click Cancel. 
NoteDuring any point in the installation process, if the 
Windows Security warning dialog box appears, click Install 
this driver software anyway.
If the Hardware Installation screen appears in Windows XP, 
click Continue Anyway.
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing4-15
Custom Mode
When selecting Custom Mode, printer port and utilities are changed 
as necessary.
1On Installation Method screen, click Custom Mode.
2On Driver tab and Utility tab of the Custom Installation screen, select 
the printer driver and utilities you want to install, and click Next.
3Select the printer you want to install, and click Next. 
4Confirm the settings and click Install. Printer driver installation 
starts.
5Installation Completed screen appears. Click Finish to return to the 
main menu. 
NoteWhen you want to add or edit the port connected to the 
printer, select the printer and Custom Select, then click Next. 
Add Standard TCP/IP Printer Port Wizard appears. Follow the 
steps in the wizard to add or edit the port.
NoteDuring any point in the installation process, if the 
Windows Security warning dialog box appears, click Install 
this driver software anyway.
If the Hardware Installation screen appears in Windows XP, 
click Continue Anyway.
Downloaded From ManualsPrinter.com Manuals