Kyocera FS 1116 User Manual

Maintenance 
OPERATION GUIDE9-5
7Slide the Charger Cleaner (green) back and 
forth 2 or 3 times to clean the charger wire, 
then return it to its original position.
8When cleaning is complete, return the Drum 
Unit to its position, aligning the guides at 
both ends with the slots in the machine. 
9Insert the Developer Unit together with the 
Toner Container, back into the machine.
10Close the Front Cover.
11Close the Scan Unit pushing the Lever.
Downloaded From ManualsPrinter.com Manuals 

Maintenance 
9-6OPERATION GUIDE
IMPORTANT: Take care not to place your 
fingers between the scan unit and the main 
body when the scan unit is closed. 
Cleaning the Machine
CAUTION: For safety purposes, always remove the power cord from the outlet 
when performing cleaning.
Always use a soft cloth dampened with alcohol or mild detergent to clean the 
machine.
Open the Document Processor and wipe 
the gray portion, as shown in the illustration.
If copies appear soiled while using the 
document processor...

Maintenance 
OPERATION GUIDE9-7
3Wipe the Pad from top to bottom. Be careful 
not to snag the Pick Spring.
Replacing the Document Processor Pad
After scanning approximately 50,000 pages through the Document Processor, the 
pressure pad may be worn out and you may experience problems with document 
feeding. In this case, it is highly recommended that you replace the pad with a new 
one. Consult your nearest service representative or authorized service center to 
order a document processor pad, and follow...

Maintenance 
9-8OPERATION GUIDE
Shipping Lock
Always slide shipping lock to Lock position 
before moving this machine from one 
location to another. And slide to Unlock 
position before using it.
Downloaded From ManualsPrinter.com Manuals 

OPERATION GUIDE10-1
10 Troubleshooting
General Guidelines
The table below provides basic solutions for problems you may encounter with the 
machine. We suggest you consult this table to troubleshoot the problems before 
calling for service.
Symptom Check Item Corrective Action Reference 
Nothing lights on 
the operation 
panel when the 
power switch is 
turned on.Is the power plug connected to 
an AC outlet?Connect the plug to an AC outlet. —
No copies 
delivered after 
[Start] is 
pressed.Is there some...

Troubleshooting 
10-2OPERATION GUIDE
Black or white 
bands on copies.
Is the charger wire dirty? Clean the charger wire.
page 9-3
Is the charger cleaner in the 
CLEANER HOME 
POSITION ? Remove the process unit and return the 
charger cleaner to its home position.
page 9-3
If you are using the document 
processor, is the slit glass 
dirty? Clean the slit glass.
It is also possible to use the Scan Noise 
Reduction function to make black lines 
on the copies less apparent. page 9-6
Skewed copies. Were the...

Troubleshooting 
OPERATION GUIDE10-3
Maintenance and Error Messages
When any of the following messages appears on the message display, perform the 
procedure provided below.
Message Procedure Reference
Close Scan UnitThe scan unit is open. Close the scan unit. —
Front Cover Open
Close coverThe front cover is open. Close the covers securely. —
Memory Low
Only 1 Copy MadeThe machine’s memory is full. Insert fewer originals and 
try to copy again.—
Open ADF cover
Remove the paperThis appears when the paper...

Troubleshooting 
10-4OPERATION GUIDE
Paper Jam
If a paper jam occurs, copying or printing will stop.
Leave the power switch on and to remove the jammed paper.
WARNING: High voltage is present in the charger section. Take sufficient care 
when working in this area, as there is a danger of electrical shock.
CAUTION: The fuser unit is extremely hot. Take care when working in this area.
Output Tray and Rear Cover
1If paper is not completely ejected into the 
Output Tray, open the Rear Cover and 
remove the...

Troubleshooting 
OPERATION GUIDE10-5
5Close the Scan Unit pushing the Lever.
The error is cleared.
IMPORTANT: Take care not to place your 
fingers between the scan unit and the main 
body when the scan unit is closed. 
Paper Cassette
1Pull out the cassette.
2Remove any partially fed paper.
Check to see if paper is loaded correctly. If 
not, reload the paper.
3Push the cassette back in firmly.
4Open the Scan Unit.
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting 
10-6OPERATION GUIDE
5Open the Front Cover.
6Close the Front Cover.
7Close the Scan Unit pushing the Lever.
The error is cleared.
IMPORTANT: Take care not to place your 
fingers between the scan unit and the main 
body when the scan unit is closed. 
Manual Feed Tray
1Remove the paper from the Manual Feed 
Tray.
IMPORTANT: Do not try to remove paper 
that has already been partially fed, proceed 
to step 2.
Downloaded From ManualsPrinter.com Manuals