Kyocera FS 1028DP User Manual

6-11
Error message for 
device errorY3 0: Does not display an 
error message and pause 
the job when the de vice error occurs.
1: Displays an error message when duplex  printing is not executed because of a possible 
limitation.
2: Displays an error message and pause the job  when running out of staples.
3: Combination of value 1 and 2.
4: Displays an error message and pause the job  when the waste punch box is full.
5: Combination of value 1 and 4.
6: Combination of value 2 and 4.
7: Combination of...

Chapter 6 Permanent Parameters
6-12
bI0—Name of the partition in memory card 
The FRPO I0 specifies a memory ca rd partition name to be automatically read at power up. Only one 
partition may be specified. The data read from the na med partition at power up will be available to 
users accessing the currently-active interface. 
The command uses the following format: 
FRPO I0, ’ partition-name’; 
Note that a comma must be placed after the I0  parameter. The partition name should not exceed 15 
printable...

 Chapter 7
Emulation
The printing systems emulate the operation of seven other printers: 
• HP LaserJet (mode 6)
• HP 7550A (mode 8)
• IBM Proprinter X24E (mode 1)
• Epson LQ-850 (mode 5)
• Diablo 630 (mode 2)
• Standard  line printer (mode 0)
• KPDL (mode 9) [PostScript compatible] 
Word-processing and graphics software for any of the above printers also works with the 
printing system. All you need to do is to set the printing system to emulate the printer 
your software supports and select  the...

Chapter 7 Emulation
7-2
Selecting an Emulation 
When installing a printing system, you can select an emulation that best suits the require-
ment by the application software. In most ca ses, the emulation will be the factory default 
setting (mode 6: HP LaserJet). Refer to th e following diagram to locate the next level 
emulation in case you need  to change the emulation. 
For example, in printing environments using the HP plotter model HP 7550A (KC-GL), 
the user should select mode 8. In PostScript...

Line Printer Emulation (Mode 0)
7-3
Automatic emulation sensing 
In printing systems that permit the selection of KPDL emulation, the automatic emula-
tion sensing (AES) can be activated so that print jobs using other emulations will auto-
matically print in the correct emulation. Refer to the AES related FRPO command 
parameters, P4 and P5, in  Interface-independent Parameters  on page 5 in Chapter 6. 
General Information on Emulation 
The printing system’s capability for supporting seven printer...

Chapter 7 Emulation
7-4
Other control codes are ignored. In particular, the escape code (ESC: character code 27) 
is ignored. If the printing system receives  the escape sequence ESC A, for example, it 
ignores the escape code and prints the letter  A. Therefore, this emulation requires PRE-
SCRIBE commands for controlling the printing system. 
In font mode (FTMD) 15, the printing system automatically gives the innate character 
spacing, line spacing, and page  orientation for each bitmap font, and...

IBM Proprinter X24E Emulation (Mode 1)
7-5
By giving a particular value for the U6 and U7 parameters, it is possible to use another 
symbol set which the Diablo does not have. For details, see LaserJet Symbol Sets on 
page 37.
At power-up or after a reset, the printing system defaults to LetterGothic (12 points, 10 
cpi). This default font emulates the IBM prin ter’s Sans-serif 10cpi font. The default font 
cannot be changed in the IBM Proprinter X24E emulation. (The FRPO C5, C2, and C3 
commands will be...

Chapter 7 Emulation
7-6
subscripts, underlining, backspace, vertical and horiz ontal tabulation, line spacing, and 
paper length. 
The font mode set for the IBM Proprinter X24E emulation is  0 (the printing system 
adjusts nothing automatically for font attributes) unless you change it by the FTMD 
command. If you do not need exact character spacing, you can improve the appearance 
of some fonts by changing the font mode to 13. 
!R! FTMD 13; EXIT; 
It should be noted that for FTMD 13; the defa ult Draft...

IBM Proprinter X24E Emulation (Mode 1)
7-7
Table 7.6.  IBM Proprinter X24E Control Codes
Command Function  Code  (hex)  Supported 
BEL Beeper 07  – 
BS Backspace 08  Yes 
HT Horizontal  Tab 09  Yes 
LF Line  Feed 0A  Yes 
VT Vertical  Tab 0B  Yes 
FF Form  Feed 0C  Yes 
CR Carriage  Return 0D  Yes 
SO  Double-Wide Printing by line  0E  Yes 
SI Condensed  Printing 0F  Yes 
DC1 Select  Printer 11  – 
DC2  10 CPI Print 12  Yes 
DC4  Cancel Double-Wide Printing 
by line 14 Yes 
CAN Cancel  Data 18  – 
ESC *...

Chapter 7 Emulation
7-8
ESC U n Set Print Direction  1B 55 n  – 
ESC W n  Continuous Double-Wide 
Printing 1B 57 n 
Yes 
ESC X n m Set Horizontal Margins  1B 58 n m Yes
ESC Y n1 n2 v1 v2...vn  Dual-Density Bit-Image  Graphics 
(Normal Speed)  1B 59 n1 n2 v1 v2...vn  Yes 
ESC Z n1 n2 v1 v2...vn  High-Density Bit-Image  Graphics 1B 5A n1 n2 v1 v2...vn  Yes 
ESC [@ n1 n2 m1 m2 m3 m4 Double-High Printing  1B 5B 40 n1 n2 m1 m2 m3 m4  Yes 
ESC [K n1 n2 in id p1 p2  Set Initial Condition  1B 5B 4B n1 n2 in id...