Konica Minolta PagePro 5650EN User Manual

Loading Media 101
7Reattach the lid of the tray.
8Push the tray completely into the 
printer.
9Select PAPER MENU/PAPER SOURCE/TRAY X (Tray 1/2/3/
4)/PAPER SIZE
 and PAPER TYPE in the configuration menu, and 
then select the setting for the size and type of the media that is loaded. 
See also “PAPER MENU” on page 36.
Downloaded From ManualsPrinter.com Manuals 

Loading Media 102
Loading the Paper Larger than A4
1Open the tray and place it on a 
flat surface.
2Remove the lid of the tray.
3Slide the right and left lock tabs 
in the tray outwards to unlock 
them.Plain paper
Envelope
Downloaded From ManualsPrinter.com Manuals 

Loading Media 103
4Hold the grip of the tray and pull 
its extendable part to the front 
until it reaches the desired paper 
size.
5Squeeze the media guide 
(length) and slide it to the 
desired paper size.
6Squeeze the media guide 
(width) and slide it to the desired 
paper size.
Downloaded From ManualsPrinter.com Manuals 

Loading Media 104
7Load the paper face up in the 
tray.
Do not load the paper above 
the 
↑ mark. For the informa-
tion on the tray capacity for 
each media, see “Media 
Types” on page 85.
8Reattach the lid of the tray.
9Push the tray completely into the 
printer. 
10Select PAPER MENU/PAPER SOURCE/TRAY X (Tray 1/2/3/
4)/PAPER SIZE
 and PAPER TYPE in the configuration menu, and 
then select the setting for the size and type of the media that is loaded. 
See also “PAPER MENU” on page 36.
Downloaded From...

Loading Media 105
Loading Banner paper in the Tray 1
1Open the tray and place it on a 
flat surface.
2Remove the lid of the tray.
3Slide the right and left lock tabs 
in the tray outwards to unlock 
them.Plain paper
Envelope
Downloaded From ManualsPrinter.com Manuals 

Loading Media 106
4Hold the grip of the tray and pull 
its extendable part to the front 
until it reaches the end.
5Squeeze the media guide 
(length) and slide it to the 
desired paper size.
6Squeeze the media guide 
(width) and slide it to the desired 
paper size.
7Load the banner paper face up 
in the tray, and then roll up the 
end of the paper so that it does 
not fall off the tray.
Downloaded From ManualsPrinter.com Manuals 

Loading Media 107
8Push the tray completely into the 
printer.
9Select PAPER MENU/PAPER SOURCE/TRAY 1/PAPER SIZE and 
PAPER TYPE in the configuration menu, and then select the setting for 
the size and type of the media that is loaded. See also “PAPER MENU” 
on page 36.
Downloaded From ManualsPrinter.com Manuals 

Duplexing 108
Duplexing
Select paper with high opacity for duplex (double-sided) printing. Opacity 
refers to how effectively paper blocks out what is written on the opposite side 
of the page. If the paper has low opacity (high translucency), then the printed 
data from one side of the page will show through to the other side. Check 
your application for margin information. For best results, print a small quantity 
to make sure the opacity is acceptable.
Duplex (double-sided) printing can be done...

Output Tray 109
In addition, if “N-up” has been set to “Booklet”, autoduplex printing is per-
formed.
The following Order settings are available when “Booklet” is selected.
1Load plain paper into the tray.
2From the printer driver, specify duplex (double-sided) printing (Layout tab 
in Windows).
3Click OK.
With autoduplexing, the back side is printed first, and then the front 
side is printed.
Output Tray
All printed media is output to the face-down output tray on top of the printer. 
This tray has a...

Finishing 110
Finishing
When the optional offset tray is installed, job separation and offset printing 
can be performed. For the installation procedure, refer to “Offset Tray” on 
page 214. Settings for job separation and offset printing can be specified by 
selecting 
JOB SEPARATION or FINISHING in PAPER MENU.
Use the following paper for job separation and offset printing.
Paper is fed to the sub output tray with job separation and offset print-
ing.
Job Separation Printing
When paper is fed to the...