Konica Minolta PagePro 4650EN User Manual
Have a look at the manual Konica Minolta PagePro 4650EN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Konica manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Lower Feeder Unit 211 6Pull out the trays. 7Lift up the printer by holding the recessed areas at both sides of the printer as shown in the fig- ure. 8With another persons help, place the printer on top of the lower feeder unit, making sure that the positioning pins on the lower feeder unit correctly fit into the holes on the bottom of the printer. The printer must be low- ered gently. Otherwise, the interior parts may be damaged. Downloaded From ManualsPrinter.com Manuals
Lower Feeder Unit 212 WARNING! This printer weighs approximately 23 kg (50.8 lbs) when it is fully loaded with consumables. The printer must be lifted by two people. 9Insert the fasteners into the 2 locations inside and 2 locations at the back of the printer. Downloaded From ManualsPrinter.com Manuals
Lower Feeder Unit 213 10Push the trays completely into the printer. 11Reconnect all interface cables. 12Reconnect the power cord, and turn on the printer. 13Declare Paper Source Unit 3/4 in the Windows printer driver (Properties/ Configure tab). Downloaded From ManualsPrinter.com Manuals
Offset Tray 214 Offset Tray When the offset tray is installed, job separation and offset printing can be per- formed. Installing the Offset Tray 1Turn off the printer and discon- nect the power cord and inter- face cables. Downloaded From ManualsPrinter.com Manuals
Offset Tray 215 2Loosen the right and left thumb- screws as shown in the figure to remove the top cover of the paper exit. 3Insert the right and left tabs of the offset tray into the holes at the top of the printer and slowly put the offset tray down to the top of the printer. Downloaded From ManualsPrinter.com Manuals
Offset Tray 216 4Tighten the two screws at both ends of the bottom of the offset tray. 5Draw the extension tray (1). When printing a thick paper, you can flip the stopper as shown in the figure below (2). 6Reconnect all interface cables. 7Reconnect the power cord, and turn on the printer. 8Declare Offset Tray in the Windows printer driver (Properties/Configure tab). Downloaded From ManualsPrinter.com Manuals
Offset Tray 217 Installing the Face Up Tray 1Insert the right and left tabs of the face up tray into the holes at the back of the printer. 2Raise the lever as shown in the figure and draw the extension tray. Downloaded From ManualsPrinter.com Manuals
Offset Tray 218 Downloaded From ManualsPrinter.com Manuals
Appendix Downloaded From ManualsPrinter.com Manuals
Safety Specifications 220 Safety Specifications Technical Specifications Printer Printer Safety standards U.S. model UL 60950-1, CSA C22.2 No. 60950-1-03 European model EU Directive 73/23/EEC EU Directive 93/68/EEC EN 60950-1 (IEC 60950) China model GB 4943 EMC standards U.S. model FCC part 15 subpart B class B ICES-003 European model EU Directive 89/336/EEC EU Directive 93/68/EEC EN 55022 (CISPR Pub. 22) class B EN 61000-3-2 EN 61000-3-3 China model GB 9254 class B, GB 17625.1 Australian model EN 55022 class B Type Desktop A4 laser beam printer Print system Semiconductor laser beam scanning system Exposure system Laser diode and polygon mirror scanning Developing system Electro photographic System (roller charging, single component magnetic toner development) Resolution 600 dpi × 600 dpi × 1 bit 1200 dpi × 1200 dpi × 1 bit Downloaded From ManualsPrinter.com Manuals