Konica Minolta magicolor 4750EN User Manual

							Status, Error, and Service Messages 9-44
TRAYX PAPER ERR
“SIZE”
“MEDIA”The media size/type 
set in the printer 
driver is different from 
the size/type of media 
loaded. This message 
appears when the 
PAPER MENU/
PAPER SOURCE/
TRAY CHAINING
 
menu is set to 
OFF.Load the correct media 
size and type.
TRAYX SIZE ERR
ADD
“SIZE”The media size set in 
the printer driver is 
different from the size 
of media loaded.Load the correct media 
size into the specified 
tray.
WASTE TONER FULL
REPLACE BOTTLEThe waste toner 
bottle is full.Install a new waste toner 
bottle.
CONFIGURATION ERRThe printer configura-
tion was changed 
when the printer 
power was on.Reboot the printer
INCORRECT
TONER XThe X toner cartridge 
is an unapproved 
type.Install a KONICA 
MINOLTA toner car-
tridge of the appropriate 
type (AM, EU, AP or 
GC). See page 7-4. This message... means... do this...
Downloaded From ManualsPrinter.com Manuals 
						

							Status, Error, and Service Messages9-45 Service Messages:
These messages indicate a more serious error that can only be corrected by 
a customer service engineer. If one of these messages appears, turn the 
printer off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.  
This service 
message...means... do this...
SERVICE CALL XXXX
“Error”
An error has been 
detected with the item 
indicated “
XXXX” in the 
service message.
Information about errors 
appears at the bottom of 
the message window.
Reboot the printer. This 
often clears the service 
message, and printer 
operation can resume. 
If the problem persists, 
contact Technical Sup-
port.
Downloaded From ManualsPrinter.com Manuals 
						

							Status, Error, and Service Messages 9-46
Downloaded From ManualsPrinter.com Manuals 
						

							10
Installing
Accessories
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction 10-2
Introduction
Note
Use of accessories not manufactured or supported by 
KONICA MINOLTA will void your warranty.
For details of accessories, visit our web site (http://printer.konicam-
inolta.com)
Note
The hard disk kit HD-P03 and CF Adapter MK-725 cannot be installed to 
be used at the same time. 
Installing accessories always requires that the printer and accessories 
are turned off and unplugged during installation.Dual In-Line 
Memory Module 
(DIMM)512 MB DIMM
Lower Feeder Unit 
PF-P07(Tray 3)500-sheet tray included
Hard Disk Kit 
HD-P03SATA Hard Disk
CF Adapter MK-725Adapter for CompactFlash card
CompactFlash 1 GB, 2 GB, 4 GB, 8 GB
Downloaded From ManualsPrinter.com Manuals 
						

							Antistatic Protection10-3
Antistatic Protection
Note
It’s very important to protect the printer controller board from 
electrostatic damage while performing any task involving the controller 
board.
Turn off all power switches first. If an antistatic wrist strap is provided in 
your printer option kit, attach one end of it to your wrist and the other 
end to the bare metal chassis on the back of your printer. Never attach 
the wrist strap to any piece of equipment with an electrical current 
present. Plastic, rubber, wood, painted metal surfaces, and telephones 
are not acceptable grounding points.
If you don’t have an antistatic wrist strap, discharge your body’s static 
electric charge by touching a grounded surface before you handle any 
printer boards or components. Also avoid walking around after 
grounding yourself.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 10-4
Dual In-Line Memory Module (DIMM)
You may need additional memory (DIMM) for complex graphics and 
for duplex (double-sided) printing. 
Dual in-line memory module (or DIMM) is compact circuit board with sur-
face-mount memory chips.
There is 256 MB of onboard memory and one available memory expansion 
slot. The memory can be expanded to a maximum of 768 MB (256 MB + 512 
MB).
Installing a DIMM
Note
It’s very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 10-3. In addition, 
always handle circuit boards by the edges only.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Using a screwdriver, remove two 
screws.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM)10-5
3Slide the panel slightly to the 
down and lift it off the printer.
4Insert the DIMM at an angle 
(about 45°) into the connector, 
making sure that the notch on 
the unit aligns with the tab on 
connector, and then press down 
carefully until it clicks into place.
Be sure to handle the 
DIMM by the edges only.
You will hear a click when 
the DIMM is properly 
placed.
5Reinstall the panel and tighten two screws.
6Reconnect all interface cables.
7Reconnect the power cord, and 
turn on the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 10-6
8Declare the additional Printer Memory in the Windows printer driver 
(Properties/Configure tab).
9Print a configuration page (PRINT MENU/CONFIGURATION PG) and 
verify that the total amount of the RAM installed in your printer is listed.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Disk Kit HD-P0310-7
Hard Disk Kit HD-P03
If you install a Hard Disk Kit HD-P03, the followings can be performed:
–Collate printing
–Job printing/saving
–Fonts/forms download
–User Authentication/Account Track
–Direct printing
–XPS printing
A hard disk kit HD-P03 and a CF Adapter MK-725 cannot be installed 
simultaneously.
Installing the Hard Disk Kit HD-P03
Note
It’s very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 10-3. In addition, 
always handle circuit boards by the edges only.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
Downloaded From ManualsPrinter.com Manuals