Konica Minolta magicolor 4650DN User Manual

							CompactFlash 227
CompactFlash
If you install a CompactFlash card, the followings can be performed:
–Collate printing
–Fonts forms download
–User Authentication/Account Track
–Direct printing (including the use of PageScope Direct Print)
Only CompactFlash cards with a capacity of 256 MB, 512 MB, 1 GB, 2 
GB or 4 GB can be used.
The job printing/saving function is not available with a CompactFlash 
card. These functions require that an optional hard disk kit be 
installed.
A hard disk kit and a CF adapter cannot be installed simultaneously.
Installing the CF adapter and CompactFlash card
Note
If the installed CompactFlash card is used with a device other than this 
printer, such as a computer or digital camera, the card is automatically 
formatted and all of its data is deleted.
Note
It is very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 219. In addition, 
always handle circuit boards by their edges only.
Downloaded From ManualsPrinter.com Manuals 
						

							CompactFlash 228
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Using a screwdriver, remove the 
screw. Then, slide the rear cover 
to the right and remove it.
3Using a screwdriver, loosen the 
seven screws. (Do not remove 
them from the printer.)
Downloaded From ManualsPrinter.com Manuals 
						

							CompactFlash 229
4Slide the panel slightly to the 
right and lift it off the printer.
5Plug the cable on the CF 
adapter into the connector on 
the controller board.
6Insert the three mounting pins 
on the CF adapter into the holes 
in the controller board to mount 
the CF adapter onto the control-
ler board.
Downloaded From ManualsPrinter.com Manuals 
						

							CompactFlash 230
7Fully insert the CompactFlash 
card into the appropriate slot.
When the CompactFlash card is 
correctly inserted, the button on 
the top side of the slot (circled in 
the illustration) slightly pops out.
Before removing the 
CompactFlash card, 
press in this button.
8Reinstall the panel and tighten the seven screws.
9Attach the rear cover.
10Reconnect all interface cables.
11Reconnect the power cord, and 
turn on the printer.
12Declare the Memory card in the Windows printer driver (Properties/Con-
figure tab).
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit 231
Lower Feeder Unit
You can install up to one optional lower feeder unit (Tray 3). The lower feeder 
unit increases your printer’s media feed capacity by 500 sheets. 
Kit Contents
„Lower feeder unit with a tray (500-sheet capacity)
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit 232
Installing a Lower Feeder Unit 
Note
Since consumables are installed in the printer, be sure to keep the 
printer level when moving it in order to prevent accidental spills.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Prepare the lower feeder unit.
Be sure to place the lower feeder unit on a level surface.
3Open the right side cover of the 
lower feeder unit.
The right side cover of the lower feeder must be opened before the 
feeder can be installed onto the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit 233
4With another person’s help, 
place the printer on top of the 
lower feeder unit, making sure 
that the positioning pins on the 
lower feeder unit correctly fit into 
the holes on the bottom of the 
printer.
WARNING!
This printer weighs approximately 37kg (81.5lb) when it is fully loaded 
with consumables. The printer must be lifted by two people.
5Close the right side cover of the 
lower feeder unit.
6Reconnect all interface cables.
37 kg37 kg81.5 lbs81.5 lbs
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit 234
7Reconnect the power cord, and 
turn on the printer.
8Declare Paper Source Unit 3 in the Windows printer driver (Properties/
Configure tab).
Downloaded From ManualsPrinter.com Manuals 
						

							Appendix
Downloaded From ManualsPrinter.com Manuals 
						

							Safety Specifications 236
Safety Specifications
Technical Specifications
Printer
Printer
Safety standards U.S. model UL 60950-1 (2003)
European model EN 60950-1 (2001)+All
China model GB 4943-2001
Taiwan CNS14336 (2004)
Korea K 60950
Others IEC-60950-1 (2001)+Country’s Differ-
ences in CB Bulletin
EMC standards U.S. model 21CFR Chapterl subchapterJ 
part1040 (Laser Notice No.50)
European model EN 60825-1 
(1994)+A2(2001)+A1(2002)
China model GB 7247.1 (2001)
Other IEC 60825-1 (1993)+A1 (1997)+A2 
(2001)
Type Desktop Tandem Full Color A4 laser beam 
printer
Print system Electro photographic Printing System 
Exposure system 4 laser diode and 1 polygon mirror
Developing system Mono-component SMT
Resolution 600 dpi × 600 dpi × 4 bits
First print Simplex 
Monochrome/Full color:
14.5 seconds for A4 or Letter 
(plain paper)
Duplex (double-sided) (magicolor 4650DN only)
Monochrome/Full color:
25 seconds for A4 or Letter 
(plain paper)
Downloaded From ManualsPrinter.com Manuals