Konica Minolta Di2011 User Manual

11.5 Safety Information
1-12 Di1611/Di2011
Introduction
Chapter 1
CDRH Regulation
This machine is certified as a Class 1 Laser product under Radiation Performance 
Standard according to the Food, Drug and Cosmetic Act of 1990. Compliance is 
mandatory for Laser products marketed in the United States and is reported to the 
Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug 
Administration of the U.S. Department of Health and Human Services (DHHS). This 
means that the device does...

1.5 Safety Information1
Di1611/Di2011 1-13
Introduction
Chapter 1
Tämä on puolijohdelaser. Laserdiodin sunrin teho on 5mW ja aallonpituus on 770-
795 nm.
Det här är en halvledarlaser. Den maximala effekten för laserdioden är 5mW och 
våglängden är 770-795 nm.
For Norway Users
Dette en halvleder laser. Maksimal effekt till laserdiode er 5mW og bølgelengde er 
770-795 nm.VARNING!
Om apparaten används på annat sätt än i denna bruksanvisning specificerats, 
kan användaren utsättas för osynlig laserstrålning,...

11.5 Safety Information
1-14 Di1611/Di2011
Introduction
Chapter 1
Laser Safety Label
A laser safety label is attached to the outside of the machine as shown below.
Ozone Release
CAUTION
Locate the Machine in a Well Ventilated Room
➜A negligible amount of ozone is generated during normal operation of this 
machine. An unpleasant odor may, however, be created in poorly ventilated 
rooms during extensive machine operations. For a comfortable, healthy, and 
safe operating environment, it is recommended that...

1.5 Safety Information1
Di1611/Di2011 1-15
Introduction
Chapter 1
Acoustic Noise
For European Users
Machine Noise Regulation 3 GSGV, 18.01.1991 : The sound pressure level at the 
operator position according to EN 27779 is equal to or less than 70dB(A).
Downloaded From ManualsPrinter.com Manuals 

11.5 Safety Information
1-16 Di1611/Di2011
Introduction
Chapter 1
Downloaded From ManualsPrinter.com Manuals 

Precautions
Chapter 2
2
2Precautions
Downloaded From ManualsPrinter.com Manuals 

22.1 Installation Precautions
2-2 Di1611/Di2011
Precautions
Chapter 2
2.1 Installation Precautions
Installation Site
To ensure utmost safety and prevent possible malfunctions, install the machine in 
a location that meets the following requirements.
-A location away from curtains, etc. that may catch fire and burn easily
-A location that is not exposed to water or other liquids
-A location free from direct sunlight
-A location out of the direct airflow of an air conditioner or heater, and not 
exposed to...

2.1 Installation Precautions2
Di1611/Di2011 2-3
Precautions
Chapter 2
Space Requirements
To ensure easy machine operation, supply replacement, and maintenance, adhere 
to the recommended space requirements detailed below.
✎
Note
Since there is a ventilation duct on the left side of the machine, be sure to allow 
a clearance of *100 mm or more on the left side.
Allow a clearance of **400 mm or more on the right side of the machine so that 
the side cover can be opened.

Unit: mm 5991024 1099
*100
**400...

22.2 Operation Precautions
2-4 Di1611/Di2011
Precautions
Chapter 2
2.2 Operation Precautions
Operating Environment
The environmental requirements for correct operation of the machine are as 
follows.
Temperature: 10°C to 30°C with fluctuations of no more than 10°C within an 
hour
Humidity: 15% to 85% with fluctuations of no more than 10% within an hour
Proper Use
To ensure the optimum performance of the machine, follow the precautions listed 
below.
-Never place heavy objects on the original glass or...

2.2 Operation Precautions2
Di1611/Di2011 2-5
Precautions
Chapter 2
CAUTION
If the ventilation duct on the left side of the machine is blocked, the inside of 
the machine will accumulate heat, resulting in a malfunction or fire.
➜Be sure to allow a clearance of 100 mm or more on the left side of the machine 
for the ventilation duct.
CAUTION
The area around the fusing unit is extremely hot.
➜Be careful not to touch any parts around the fusing unit, other than those 
indicated in this manual, in order to...