Konica Minolta bizhub C20P User Manual

Configuration Menu Overview 77
LCD 
CONTRAST
SECURITYCHANGE 
PASSWORD
LOCK PANEL
CLOCKDATE 
(xx.xx.xx)
TIME
HDD FORMAT*USER AREA 
ONLY
ALL
RESTORE 
DEFAULTSRESTORE 
NETWORK
RESTORE 
PRINTER
RESTORE ALL
ENERGY 
SAVER TIME**
MENU 
TIMEOUT
ENERGY 
SAVER
TIME ZONE
HOLD JOB 
TIMEOUT*
CARD FOR-
MAT***USER AREA 
ONLY
ALL
Downloaded From ManualsPrinter.com Manuals 

Configuration Menu Overview 78
* These menu items appear only if an optional hard disk kit is installed.
** This menu item appears when you select 
ON from the ENERGY 
SAVER
 menu.
*** This menu item appears only if an optional CompactFlash card is 
installed.
**** This menu item appears only if the optional lower feeder unit is 
installed.
***** This menu item appears only if an optional hard disk kit or a 
CompactFlash card is installed.
ENABLE 
WARNINGPAPER EMPTYTRAY1
TRAY2
TRAY3****
TONER LOW
I-UNIT...

Configuration Menu Overview 79
All factory default values are shown in bold.
LAN-
GUAGESettingsENGLISH/FRENCH/GERMAN/SPANISH/
ITALIAN/PORTUGUESE/CZECH/JAPANESE/
KOREAN/SIMPLIFIED CHINESE/
TRADITIONAL CHINESE/DUTCH/RUSSIAN/
POLISH
The display language of the message window can be changed 
to the selected language.
The language selections appear in the message window in the 
corresponding language. For example, 
GERMAN appears as 
DEUTSCH.
EMULA-
TIONDEF. 
EMULA-
TIONSettingsAUTO/POSTSCRIPT/PCL
Specify...

Configuration Menu Overview 80
PCL CR/LF 
MAP-
PINGSettingsCR=CR LF=LF/CR=CRLF 
LF=LF/CR=CR 
LF=LFCR/CR=CRLF 
LF=LFCR
Select the definitions of the CR/LF codes 
in the PCL language.
LINES 
PER 
PAGESettings5-60-128
Specify the number of lines per page in the 
PCL language.
FONT 
SOURCEFONT 
NUMBERSettings0-102
Specify the default font in the 
PCL language.
The font numbers that appear 
correspond to the PCL font list. 
For details on printing the font 
list, refer to “PRINT MENU” on 
page 35.
PITCH...

Configuration Menu Overview 81
XPS DIGI-
TAL
SIGNA-
TURESettingsENABLE/DISABLE
Select whether to enable or disable XPS 
digital signatures.
If 
ENABLE is selected, XPS digital 
signatures are enabled.
If 
DISABLE is selected, XPS digital 
signatures are disabled.
XPS 
ERROR 
PAGESettingsON/OFF
Select whether or not an error report is 
printed after an XPS error has occurred.
If 
ON is selected, the error report is printed.
If 
OFF is selected, the error report is not 
printed.
PAPER DEFAULT 
PAPERPAPER...

Configuration Menu Overview 82
CUSTOM 
SIZESpecify the media size when PAPER 
SIZE
 is set to CUSTOM.
The setting units can be switched between 
millimeters and inches with the 
SYS 
DEFAULT MENU/PAPER/UNIT OF 
MEASURE
 setting.
Setting range for 
WIDTH
„For MILLIMETERS: 92 to 216 mm
(default)
–North America: 216 mm
–All other regions: 210 mm
„For INCHES: 3.63 to 8.50 inches
(default)
–North America: 8.50 inches
–All other regions: 8.26 inches
Setting range for LENGTH
„For MILLIMETERS: 148 to 356 mm...

Configuration Menu Overview 83
PAPER 
TYPESettingsPLAIN PAPER/
RECYCLED/THICK 1/
THICK 2/LABEL/
TRANSPARENCY/
ENVELOPE/POSTCARD/
LETTERHEAD/GLOSSY 1/
GLOSSY 2
Select the type of media that is normally 
used.
UNIT 
OF 
MEA-
SURESettingsINCHES/MILLIMETERS
The units for specifying the size of custom media can 
be switched between inches and millimeters.
The default setting for North America is 
INCHES. The default setting for all other 
regions is 
MILLIMETERS.
GRAY 
SCALE 
PAGESettingsAUTO/GRAYSCALE...

Configuration Menu Overview 84
AUTO 
CON-
TINUESettingsON/OFF
Select whether or not printing continues if the size or type of 
media in the selected tray is different from the size or type of 
media for the print job.
If 
AUTO CONTINUE is set to ON, printing automatically contin-
ues after about 10 seconds under the following conditions. At 
this time, printing will be performed even if the media size is dif-
ferent.
No media: PAPER EMPTY (Page 211)/TRAY EMPTY (Page 
213)
Different media size/type: PAPER...

Configuration Menu Overview 85
LCD 
CON-
TRASTSettings-3/-2/-1/0/+1/+2/+3
Adjust the contrast of the message window.
The darkest level setting is 
-3 and the brightest level setting is 
+3.
SECU-
RITYCHANGE 
PASS-
WORDSpecify the password for locking the control panel.
If the password is set to 
0000 (default), the control 
panel is not locked. In order to lock the control panel, 
be sure to specify a password other than 
0000.
LOCK 
PANELSettingsOFF/MINIMUM/ON
Specify how the control panel is locked.
If...

Configuration Menu Overview 86
CARD 
FORMATUSER 
AREA 
ONLYInitialize the user area of the compactflash card. 
When this menu item is selected, the printer is 
automatically restarted.
ALLInitialize the compactflash card. When this menu item 
is selected, the printer is automatically restarted.
RESTORE 
DEFAULTSRESTORE 
NETWORKReset the network settings to their defaults. When 
this menu item is selected, the printer is 
automatically restarted.
RESTORE 
PRINTERReset the printer settings to their...