Konica Minolta bizhub 600 User Manual

2Before Making Copies
2-22 bizhub 750/600
Before Making Copies
Chapter 2
2.2 Adjusting the Angle of the Control Panel
The control panel can be adjusted to either of two angles.
Adjust the control panel to the angle that allows for easy operation.
To adjust the angle of the control panel
1Press the control panel 
release lever, and then 
push down on the con-
trol panel.
Downloaded From ManualsPrinter.com Manuals 

Before Making Copies2
bizhub 750/600 2-23
Before Making Copies
Chapter 2
The control panel stops 
at the lower position.
2To return the control 
panel to the upper posi-
tion, press the control 
panel release lever, and 
then pull up on the con-
trol panel.
2
Note 
The control panel can also be grabbed anywhere on its outer edge and 
lifted.
Downloaded From ManualsPrinter.com Manuals 

2Before Making Copies
2-24 bizhub 750/600
Before Making Copies
Chapter 2
2.3 Turning on the Main Power and the Sub Power
This machine has two power controls: the main power switch and the sub 
power switch.
To turn on the machine
The main power switch turns on/off all functions of the machine. Normally, 
the main power switch is turned on.
The sub power switch turns on/off machine operations, for example, for cop-
ying, printing or scanning. When the sub power switch is turned off, the ma-
chine enters a...

Before Making Copies2
bizhub 750/600 2-25
Before Making Copies
Chapter 2
3Turn on the sub power 
switch.
!
Detail 
When the control panel is turned on by using the sub power switch, the 
indicator on the [Start] key lights up in orange, and a screen indicating 
that the machine is starting up appears.
After a few seconds, the message “Now warming up. Ready to scan.” ap-
pears on the touch panel, and the indicator on the [Start] key lights up in 
green, indicating that a job can now be queued.
!
Detail...

2Before Making Copies
2-26 bizhub 750/600
Before Making Copies
Chapter 2
To scan during warm-up
1Turn on the sub power switch.
The indicator on the [Start] key lights up in orange.
?How is the machine turned on?
%For details on turning on the machine, refer to “To turn on the ma-
chine” on page 2-24.
2Check that the message “Now warming up. Ready to scan.” appears 
on the touch panel.
– After the warm-up message is displayed, the Basic screen appears.
The indicator on the [Start] key lights up in green....

Before Making Copies2
bizhub 750/600 2-27
Before Making Copies
Chapter 2
5Specify any necessary copy settings.
6Press the [Start] key.
The original is scanned, and the job is added to the list of queued jobs.
7Check that the original has finished being scanned, and then position 
the next original.
8Specify new copy settings and the desired number of copies, and then 
press the [Start] key. 
– After the machine has finished warming up, the jobs will automati-
cally be printed in the order that they were...

2Before Making Copies
2-28 bizhub 750/600
Before Making Copies
Chapter 2
To turn off the machine
1Turn off the sub power 
switch.
The touch panel goes 
off.
The main power indica-
tor lights up in green.
2Turn off the main power 
switch.
2
Reminder 
Do not turn off the machine with the main power switch or the sub power 
switch while it is making copies or printing, otherwise a paper misfeed 
may occur.
Do not turn off the machine with the main power switch or the sub power 
switch while it is scanning...

Before Making Copies2
bizhub 750/600 2-29
Before Making Copies
Chapter 2
!
Detail 
The following are cleared when the main power switch and sub power 
switch are turned off.
Settings that have not been programmed
Jobs queued to be printed
When turning the main power switch off then on, be sure to wait 10 sec-
onds or longer before turning it on again;
otherwise the machine may not operate properly.
Automatically Canceling the Settings (Automatic Panel Reset)
If the [Reset] key is not pressed and no...

2Before Making Copies
2-30 bizhub 750/600
Before Making Copies
Chapter 2
Automatically Conserving Energy (Low Power Mode)
If no operation is performed for a specified length of time, the touch panel 
goes off and the machine automatically enters a mode where it conserves 
energy.
This is the Low Power mode.
The machine can receive jobs even while it is in Low Power mode.
As the factory default, the machine enters Low Power mode after 15 minutes.
To recover from Low Power mode
1Press the [Power Save]...

Before Making Copies2
bizhub 750/600 2-31
Before Making Copies
Chapter 2
Automatically Conserving Energy (Sleep Mode)
If no operation is performed for a specified length of time, the machine auto-
matically enters a mode where it conserves energy.
Although the machine conserves more energy in Sleep mode than in Low 
Power mode, the machine must warm up when Sleep mode is canceled to 
begin printing again, therefore taking more preparation time than Low Power 
mode.
As the factory default, the machine...