Konica Minolta bizhub 131f User Manual

Getting started4
bizhub 131f/190f 4-7
4.2 Document and Paper handling
4.2.1 Document handling
Before you begin the sending, copying, or scanning, please read the follow-
ing guidelines.
Acceptable document
ADF
* In the real time transmission with super-fine mode, 216 x 356 mm.
Document glass
Single-sheet Multiple-sheet 
Size 
(W × L) Max. 216 × 900 mm* 
Min. 120 × 100 mm Max. 216 × 356 mm
Min. 216 × 139.5 mm 
Quantity  1 sheet  Max. 80 sheets of A4-, A5 -, 
or F4-size sheets 
(75 g/m² or 20lb. paper)...

4Getting started
4-8 bizhub 131f/190fThings not to put in your machine
To prevent jams and damage in the ADF, DO NOT insert:
-Folded, curled, torn, wrinkled or very thin pages
-Documents with staples, glue, tape, paper clips or still-wet correction flu-
id
-Sticky notes (or documents with sticky notes attached)
-Cardboard, newspaper or fabric
-Pages with duplicating carbon on either side
-Credit cards or any small, thick items
-OHP transparency film
Scanned area
The scanned area is shown below.
Fax: 208...

Getting started4
bizhub 131f/190f 4-9Loading the documents in the ADF
1Insert the documents, face up, top 
edge first.
2Adjust the document guides to the 
document size.
Loading the document on the document glass
1Make sure there is no documents in 
the ADF
.
2Lift the platen cover.
3Place the document face down on the document glass. The document 
should be aligned to the upper left corner.
4Gently close the platen cover.
7IMPORTANT
%When copying a bound document, such as a book, the copied image 
may...

4Getting started
4-10 bizhub 131f/190f
4.2.2 Paper handling
Acceptable paper size
Paper cassette
Bypass Tray
Duplex printing
-Custom-sized paper can be used for PC printing only
-A5-sized paper cannot use for PC printing, but A5 š is available.
-Do not use envelopes with double flaps or pressure seals as these do not 
feed properly.
-If using a transparency (OHP) film, be sure that the film does not have a 
paper back-ing and/or a leading strip. If it does, remove the paper back-
ing and/or strip before...

Getting started4
bizhub 131f/190f 4-11Paper you cannot use
To prevent jams and damage in your machine, 
do not use the following pa-
per:
-Creased paper
-Wrinkled paper
-Folded paper
-Curled paper
-Torn paper
-Carbon paper
-Moist paper
-Very thin paper
-Very thick paper
-Previously printed by a printer
-Paper with holes
-Envelopes with pressure seals
-Extremely shiny or highly textured
Downloaded From ManualsPrinter.com Manuals 

4Getting started
4-12 bizhub 131f/190fPrintable area
The printable area is shown below.
Loading paper in the paper cassette
2
Note
After you load the paper in paper cassette, you need to set the paper size 
you loaded. (See “Setting of the Paper Size” on page 4-17.)
1Pull to open the paper cassette.
2Press down the paper lifting plate 
until it locks in position.
3 mm (0.12)
3 mm (0.12)
3 mm (0.12)3 mm (0.12)Printable area
Downloaded From ManualsPrinter.com Manuals 

Getting started4
bizhub 131f/190f 4-13
3Adjust the rear paper guide to the de-
sired paper length.
4Load the paper into the cassette.
-Before you insert paper in the cassette, stack it so the leading edge 
and sides of the paper are even.
-Do not stack the paper over the limit mark inside of the cassette.
2
Note
To prevent paper jams, do not refill this paper cassette without first re-
moving all of any paper which may remain in it. In other words, do not just 
add sheets to an already-loaded stack....

4Getting started
4-14 bizhub 131f/190f
6Close the paper cassette.
7After loading paper in the paper cassette, you need to set the paper 
size. (See “Setting of the Paper Size” on page 4-17.)
8Attach the paper size sticker supplied with your machine on the cas-
sette’s front.
Downloaded From ManualsPrinter.com Manuals 

Getting started4
bizhub 131f/190f 4-15Loading paper in bypass tray
When you need to use a size of paper not currently loaded in the paper cas-
sette, or when you want to print on a envelope, transparency film or custom 
sized paper, use the bypass tray.
2
Note
Always load only use print media specified in “Acceptable paper size” on 
page 4-10 to avoid paper jams and print quality problems.
1Open the bypass tray on the right 
side of your machine. Spread the pa-
per support extension.
2To set the paper,...

4Getting started
4-16 bizhub 131f/190f
3Adjust the paper guides (1) to fit the 
paper, then lower the flapper release 
lever (2).
4After loading paper on the bypass 
tray, you need to set the correct pa-
per size by pressing [Bypass].
5Press [,] or [+] to select the paper 
size you want to use.
6Press [Enter].
2
Note
You can set the default paper size for the bypass tray. See step 6 of “Set-
ting of the Paper Size” on page 4-17.
Downloaded From ManualsPrinter.com Manuals