KitchenAid Refrigerator Kfcs22evms 7 Manual

							THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING, 
please visit our website at www.kitchenaid.com for additional information. If you still need assistance, call us at 1-800-422-1230. 
In Canada, visit our website at www.kitchenaid.ca or call us at 1-800-807-6777. 
You will need your model and serial number, located on the inside wall of the refrigerator compartment.
   
REFRIGERATOR SAFETY
Table of Contents  /  Índice / Table des matières
REFRIGERATOR SAFETY ............................... 1
INSTALLATION INSTRUCTIONS .................... 2
REFRIGERATOR USE ...................................... 7
REFRIGERATOR CARE ................................. 10
TROUBLESHOOTING .................................... 11
WATER FILTER CERTIFICATIONS............... 13
PRODUCT DATA SHEETS ............................ 14
WARRANTY .................................................... 16SEGURIDAD DEL REFRIGERADOR............. 18
INSTRUCCIONES DE INSTALACIÓN........... 19
USO DE SU REFRIGERADOR....................... 24
CUIDADO DE SU REFRIGERADOR ............. 27
SOLUCIÓN DE PROBLEMAS ....................... 28
HOJA DE DATOS DEL PRODUCTO ............. 31
GARANTÍA ...................................................... 33SÉCURITÉ DU RÉFRIGÉRATEUR ................ 35
INSTRUCTIONS D’INSTALLATION .............. 36
UTILISATION DU RÉFRIGÉRATEUR............ 41
ENTRETIEN DU RÉFRIGÉRATEUR .............. 44
DÉPANNAGE .................................................. 45
FEUILLES DE DONNÉES 
SUR LE PRODUIT .......................................... 48
GARANTIE ...................................................... 50
REFRIGERATOR USER INSTRUCTIONS
W10326028A
You can be killed or seriously injured if you dont immediately 
 
You
 can be killed or seriously injured if you dont
follow 
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety 
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.DANGER
WARNING 
						

							2
Proper Disposal of Your Old Refrigerator
IMPORTANT: Child entrapment and suffocation are not problems 
of the past. Junked or abandoned refrigerators are still dangerous 
– even if they will sit for “just a few days.” If you are getting rid of 
your old refrigerator, please follow these instructions to help 
prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
■Take off the doors.
■Leave the shelves in place so that children may not easily 
climb inside.
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
Remove the Packaging
■Remove tape and glue residue from surfaces before turning 
on the refrigerator. Rub a small amount of liquid dish soap 
over the adhesive with your fingers. Wipe with warm water 
and dry.
■Do not use sharp instruments, rubbing alcohol, flammable 
fluids, or abrasive cleaners to remove tape or glue. These 
products can damage the surface of your refrigerator. For 
more information, see “Refrigerator Safety.”
■Dispose of/recycle all packaging materials. 
Clean Before Using
After you remove all of the packaging materials, clean the inside of 
your refrigerator before using it. See the cleaning instructions in 
“Refrigerator Care.”
IMPORTANT SAFETY INSTRUCTIONS
WARNING: 
To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions: 
SAVE THESE INSTRUCTIONS
■ Plug into a grounded 3 prong outlet.
■ Do not remove ground prong.
■ Do not use an adapter.
■ Do not use an extension cord.
■ Disconnect power before servicing. 
■ Replace all parts and panels before operating.
■ Remove doors from your old refrigerator.
■ Use nonflammable cleaner.
■ Keep flammable materials and vapors, such as gasoline, 
away from refrigerator. 
■ Use two or more people to move and install refrigerator.
■ Disconnect power before installing ice maker (on ice maker 
kit ready models only).
 
■ Use a sturdy glass when dispensing ice (on some models).
■ Do not hit the refrigerator glass doors (on some models).
WARNING
Suffocation Hazard
Remove doors from your old refrigerator. 
Failure to do so can result in death or brain damage.
WARNING
Excessive Weight Hazard
Use two or more people to move and install 
refrigerator.
Failure to do so can result in back or other injury.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for 
cleaning or service, be sure to cover the floor with 
cardboard or hardboard to avoid floor damage. Always pull 
the refrigerator straight out when moving it. Do not wiggle or 
“walk” the refrigerator when trying to move it, as floor 
damage could occur.
Important information to know about glass shelves 
and covers:
Do not clean glass shelves or covers with warm water when 
they are cold. Shelves and covers may break if exposed to 
sudden temperature changes or impact, such as bumping. 
Tempered glass is designed to shatter into many small, 
pebble-size pieces. This is normal. Glass shelves and covers 
are heavy. Use both hands when removing them to avoid 
dropping. 
						

							3
Location Requirements
To ensure proper ventilation for your refrigerator, allow for ¹⁄₂ 
(1.25 cm) of space on each side and at the top. Allow for 1 
(2.54 cm) of space behind the refrigerator. If your refrigerator has 
an ice maker, allow extra space at the back for the water line 
connections. When installing your refrigerator next to a fixed wall, 
leave 2¹⁄₂ (6.3 cm) minimum on the hinge side (some models 
require more) to allow for the door to swing open.
NOTE: It is recommended that you do not install the refrigerator 
near an oven, radiator, or other heat source. Do not install the 
refrigerator in a location where the temperature will fall below 55°F 
(13°C).
Electrical Requirements
Before you move your refrigerator into its final location, it is 
important to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded 
electrical supply is required. It is recommended that a separate 
circuit serving only your refrigerator be provided. Use an outlet 
that cannot be turned off by a switch. Do not use an 
extension cord.
NOTE: Before performing any type of installation, cleaning, or 
removing a light bulb, turn Cooling OFF, and then disconnect the 
refrigerator from the electrical source. When you are finished, 
reconnect the refrigerator to the electrical source and turn Cooling 
ON. See “Using the Controls.”
Water Supply Requirements
Gather the required tools and parts before starting installation. 
Read and follow the instructions provided with any tools listed 
here.
TOOLS NEEDED:  
IMPORTANT:
■All installations must meet local plumbing code requirements.
■Do not use a piercing-type or ³⁄₁₆ (4.76 mm) saddle valve 
which reduces water flow and clogs more easily.
■Use copper tubing and check for leaks. Install copper tubing 
only in areas where the household temperatures will remain 
above freezing.
■For models with water filters, the disposable water filter 
should be replaced at least every 6 months. 
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as 
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
2¹⁄₂ (6.3 cm)
¹⁄₂ (1.25 cm)
■Flat-blade screwdriver
■⁷⁄₁₆ and ¹⁄₂ Open-end or two 
adjustable wrenches
■¹⁄₄ Nut driver
■¹⁄₄ Drill bit
■Cordless drill
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, 
fire, or electrical shock.
WARNING 
						

							4
Water Pressure
A cold water supply with water pressure of between 35 and 
120 psi (241 and 827 kPa) is required to operate the water 
dispenser and ice maker. If you have questions about your water 
pressure, call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a 
reverse osmosis system going to the water inlet valve of the 
refrigerator needs to be between 35 and 120 psi (241 and 
827 kPa).
If a reverse osmosis water filtration system is connected to your 
cold water supply, the water pressure to the reverse osmosis 
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than 
40 to 60 psi (276 to 414 kPa):
■Check to see whether the sediment filter in the reverse 
osmosis system is blocked. Replace the filter if necessary.
■Allow the storage tank on the reverse osmosis system to refill 
after heavy usage.
■If your refrigerator has a water filter, it may further reduce the 
water pressure when used in conjunction with a reverse 
osmosis system. Remove the water filter. See “Water Filtration 
System.”
If you have questions about your water pressure, call a licensed, 
qualified plumber.
Connect the Water Supply
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line is 
connected, turn the ice maker OFF.
Connect to Water Line
1.Unplug refrigerator or disconnect power.
2.Turn OFF main water supply. Turn ON nearest faucet long 
enough to clear line of water.
3.Find a ¹⁄₂ to 1¹⁄₄ (12.7 mm to 31.8 mm) vertical cold water 
pipe near the refrigerator.
IMPORTANT:
■Make sure it is a cold water pipe. 
■Horizontal pipe will work, but the following procedure 
must be followed: Drill on the top side of the pipe, not the 
bottom. This will help keep water away from the drill. This 
also keeps normal sediment from collecting in the valve.
4.Determine the length of copper tubing you need. Measure 
from the connection on the rear of the refrigerator to the water 
pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄ (6.35 mm) 
O.D. (outside diameter) copper tubing. Be sure both ends of 
copper tubing are cut square.
5.Using a cordless drill, drill a ¹⁄₄ hole in the cold water pipe you 
have selected.
 
6.Fasten the shutoff valve to the cold water pipe with the pipe 
clamp. Be sure the outlet end is solidly in the ¹⁄₄ drilled hole in 
the water pipe and that the washer is under the pipe clamp. 
Tighten the packing nut. Tighten the pipe clamp screws slowly 
and evenly so the washer makes a watertight seal. Do not 
overtighten. 
7.Slip the compression sleeve and compression nut on the 
copper tubing as shown. Insert the end of the tubing into the 
outlet end squarely as far as it will go. Screw compression nut 
onto outlet end with adjustable wrench. Do not overtighten or 
you may crush the copper tubing. 
8.Place the free end of the tubing in a container or sink, and turn 
ON the main water supply. Flush the tubing until water is clear. 
Turn OFF the shutoff valve on the water pipe. 
Connect to Refrigerator 
1.Create a service loop (minimum diameter of 2 ft [61 cm]) with 
the copper tubing. Avoid kinks when coiling the copper 
tubing. 
2.Remove the plastic cap from water valve inlet port. Place a 
compression nut and sleeve on the copper tubing. 
3.Insert the end of the copper tubing into the water valve inlet 
port. Shape tubing slightly so that the tubing feeds straight 
into the port to avoid kinks.
4.Slide the compression nut over the sleeve and screw into the 
water valve inlet port. 
5.Using an adjustable wrench, hold the nut on the plastic water 
line to keep it from moving. Then, with a second wrench turn 
the compression nut on the copper tubing counterclockwise 
to completely tighten. Do not overtighten.
6.Check connection by pulling on copper tubing. Attach copper 
tubing to refrigerator cabinet with a “P” clamp. Turn on water 
supply to refrigerator and check for leaks. Correct any leaks.
A. Cold water pipe
B. Pipe clamp
C. Copper tubing 
D. Compression nutE. Compression sleeve
F. Shutoff valve
G. Packing nut
F
G
A
B
C
D
E
A. Plastic water tubing
B. SleeveC. Compression nut
D. Copper tubing
A. Plastic water line
B. Water valve inlet port
C. Compression nutD. Copper tubing
E. “P” clamp
B
A
C
D
C
B
D
E
A 
						

							5
Complete the Installation
1.Plug into a grounded 3 prong outlet.
NOTE: Allow 24 hours to produce the first batch of ice. Discard 
the first three batches of ice produced. Allow 3 days to completely 
fill the ice container.
Refrigerator Door(s) and Drawer
Graphics are included later in this section.
Remove and Replace Handles 
1.Using a ³⁄₃₂ or ¹⁄₈ hex key, loosen the two setscrews located 
on the side of each handle. See Graphics 1 and 2.
2.Pull the handle straight out from the door. Make sure you keep 
the screws for reattaching the handles.
3.To replace the handles, reverse the directions.
Remove Doors and Hinges
IMPORTANT: 
■Remove food and any adjustable door or utility bins from 
doors.
■All graphics referenced in the following instructions are 
included later in this section after “Final Steps.”
TOOLS NEEDED: ⁵⁄₁₆, ³⁄₈, ¹⁄₄ hex-head socket wrench, 
#2 Phillips screwdriver, and a flat-blade screwdriver.
1.Unplug refrigerator or disconnect power.
2.Keep the refrigerator doors closed until you are ready to lift 
them free from the cabinet.
NOTE: Provide additional support for the refrigerator door 
while the hinges are being removed. Do not depend on the 
door gasket magnets to hold the door in place while you are 
working.
3.Starting with the right-hand side door, remove the parts for the 
top hinge as shown in Top Hinge graphic. Lift the refrigerator 
door from the bottom hinge pin.
NOTE: Remove the hinge pin cover from the bottom hinge pin 
and keep it for later use. See Bottom Hinge graphic. 
4.Before removing the left-hand side door, disconnect the wiring 
plug located on top of the top hinge by wedging a flat-blade 
screwdriver or your fingernail between the two sections. See 
Wiring Plug graphic.
5.Remove the parts for the top hinge as shown in Top Hinge 
graphic. Lift the left-hand side door from the bottom hinge pin.
NOTE: Remove the hinge pin cover from the bottom hinge pin 
and keep it for later use. See Bottom Hinge graphic. 
Replace Doors and Hinges
1.Assemble the parts for the top hinge as shown in Top Hinge 
graphic. Do not tighten the screws completely.
2.Replace the parts for the bottom hinge as shown in Bottom 
Hinge graphic. Tighten screws. Replace the refrigerator door.
NOTE: Provide additional support for the refrigerator door 
while the hinges are being moved. Do not depend on the door 
gasket magnets to hold the door in place while you are 
working.
3.Align the door so that the bottom of the refrigerator door 
aligns evenly with the top of the freezer drawer. Tighten all 
screws.
4.Reconnect the wiring plug on top of the left-hand side 
refrigerator door.
5.Replace the top hinge covers.
Remove and Replace Freezer Drawer Front
IMPORTANT: Two people may be required to remove and replace 
the freezer drawer front. Graphics are included later in this 
section.
Remove Drawer Front
1.Open the freezer drawer to full extension.
2.Loosen the four screws attaching the drawer glides to the 
drawer front. See Drawer Front Removal graphic.
NOTE: Loosen screws three to four turns. Keep the screws in 
the drawer front.
3.Lift drawer front upward and off the screws. See Drawer Front 
Removal graphic. 
Replace Drawer Front
1.Slide the drawer glides out of the freezer compartment. Insert 
the screws in the top of the drawer front into the slots in the 
drawer brackets. See Drawer Front Replacement graphic. 
2.Pull the drawer brackets toward you to position the two 
screws in the bottom of the drawer front into the brackets. 
See Drawer Front Replacement graphic.
3.Completely tighten the four screws.
Final Steps
1.Plug into a grounded 3 prong outlet.
2.Return all removable door parts to doors and food to 
refrigerator.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, 
fire, or electrical shock.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, 
fire, or electrical shock.
WARNING 
						

							6
Door Removal & Replacement
A. Hinge Pin Cover
C. Hinge Screws B. Bottom Hinge
Bottom Hinges
Wiring Plug
A
B
C
1
A. ³⁄₃₂ or ¹⁄₈ SetscrewsA. ³⁄₃₂ or ¹⁄₈ Setscrews
2
A
A
Drawer Front Removal
A. Loosen 4 Door Bracket Screws
A
Drawer Front Replacement
Top Hinges
A. Hinge Cover Screw
B. Top Hinge Cover
C. ⁵⁄₁₆ Hex-Head Hinge Screws
D. Top Hinge
B
A
C
D 
						

							7
Adjust the Doors
IMPORTANT:
■Your refrigerator has two adjustable, front leveling screws – 
one on each side of the refrigerator base. If your refrigerator 
seems unsteady or you want the door to close easier, use the 
instructions below.
■Before moving the refrigerator, raise the leveling screws so the 
front rollers are touching the floor. 
1.Remove the base grille. Grasp the grille firmly and pull it 
toward you.
2.Raise or lower the cabinet. 
Using a ¹⁄₄ hex driver, turn the leveling screw on each side to 
raise or lower that side of the refrigerator.
NOTE: Having someone push against the top of the 
refrigerator takes some weight off the leveling screws. This 
makes it easier to turn the screws. It may take several turns of 
the leveling screw to adjust the tilt of the refrigerator.
■To raise, turn the leveling screw clockwise.
■To lower, turn the leveling screw counterclockwise. 
3.Open the door again to make sure that it closes as easily as 
you like. If not, tilt the refrigerator slightly more to the rear by 
turning both leveling screws clockwise. It may take several 
more turns, and you should turn both screws the same 
amount.
4.Replace the base grille.
REFRIGERATOR USE
Opening and Closing Doors
There are two refrigerator compartment doors. The doors can be 
opened and closed either separately or together.
There is a vertically-hinged seal on the left refrigerator door.
■When the left side door is opened, the hinged seal 
automatically folds inward so that it is out of the way.
■When both doors are closed, the hinged seal automatically 
forms a seal between the two doors. 
Using the Controls
The control center is located at the top front of the refrigerator 
compartment. 
Temperature Controls
For your convenience, your temperature controls are preset at the 
factory. When you first install your refrigerator, make sure the 
controls are still set to the recommended set points as shown.
Recommended Settings
IMPORTANT: 
■The recommended settings should be correct for normal 
household refrigerator use. The controls are set correctly 
when milk or juice is as cold as you like and when ice cream is 
firm.
■When the power is on, the temperature display shows the 
actual temperature of the compartment.
■Wait 24 hours for your refrigerator to cool completely before 
adding food. If you add food before the refrigerator has cooled 
completely, your food may spoil.
NOTE: Adjusting the refrigerator and freezer temperature 
controls to a colder than recommended setting will not cool 
the compartments any faster.
■If the temperature is too warm or too cold in the refrigerator or 
freezer, first check the air vents to be sure they are not 
blocked before adjusting the controls. 
A. Leveling screw
A
A. Hinged seal
A 
						

							8 Cooling On/Off:
■Cooling On/Off turns off cooling for both compartments. It 
does not disconnect power to the refrigerator. 
■Press and hold Cooling On/Off for 3 seconds. The LED will 
light up to indicate that cooling is Off. Press the button again 
to turn on the cooling. The LED will turn off. 
Adjusting Controls
The REFRIGERATOR control adjusts the refrigerator compartment 
temperature. The FREEZER control adjusts the freezer 
compartment temperature. 
If you need to adjust the temperature in either the refrigerator or 
freezer compartment, use the settings listed in the chart as a 
guide.
To Adjust Set Point Temperatures:
The first touch of the (+) or (-) touch pad displays the current 
temperature set point. 
■Press the (+) or (-) touch pads until the desired temperature 
set point is displayed.
NOTE: Except when first turning on the refrigerator, do not 
adjust either temperature control more than one setting at a 
time. Wait 24 hours between adjustments for the temperature 
to stabilize.   
Additional Control Center Features
Humidity Control 
The Humidity Control feature turns on a heater to help reduce 
moisture on the door hinge seal. Use in humid environments or 
when you notice moisture on the door hinge seal. The refrigerator 
uses more energy when Humidity Control is on.
■Press Humidity Control when the environment is warm and 
more humid, or if you notice moisture on the door hinge seal. 
The indicator light will be lit when humidity control is ON. 
■Press Humidity Control again to turn OFF and save energy 
when the environment is less humid. 
Sabbath Mode 
The Sabbath Mode is designed for those whose religious 
observances require turning off the lights and dispensers.
ON - All interior lights and alarm tones will be disabled.
OFF - All interior lights and alarm tones will be enabled.
■Press and hold the Sabbath Mode touch pad for 3 seconds or 
until the indicator light is lit to turn on this feature. Press and 
hold the Sabbath Mode touch pad again to turn off this 
feature. 
Door Alarm
The Door Alarm feature sounds a chime every few seconds when 
the refrigerator door has been left open for 5 continuous minutes. 
The chime will sound until the door is closed or Door Alarm is 
turned off.
■Press the Door Alarm to turn this feature ON or OFF. The 
indicator light will be lit when the Door Alarm feature is on. 
Max Cool
The Max Cool feature assists with periods of high refrigerator use, 
full grocery loads, or temporarily warm room temperatures.
■Press Max Cool to set the freezer and refrigerator to the 
lowest temperature settings. Press Max Cool again to return 
to the normal refrigerator set point.
NOTE: The Max Cool feature will automatically shut off in 
approximately 12 hours.
Filter Reset
The Filter Reset control allows you to restart the water filter status 
tracking feature each time you replace your water filter. See 
“Water Filtration System.”
■Press and hold the Filter Reset touch pad for 3 seconds, until 
the Order or Replace light turns off. 
User Preferences
The control center allows you to set user preferences, if desired. 
Temperature Display (F_C)
This preference allows you to change the temperature display.
F - Temperature in degrees Fahrenheit
C - Temperature in degrees Celsius 
Alarm (AL)
This preference allows you to turn off the sound of all alarms.
ON - You will hear the alarm sound.
OFF - You will not hear the alarm sound.
To Access the User Preferences Menu:
1.Press and hold the Door Alarm touch pad for 3 seconds. The 
preference name will appear in the Freezer display and the 
preference status (F or C) or (ON or OFF) will appear in the 
Refrigerator display. CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm REFRIGERATOR Control 
1° lower 
FREEZER too warm/too little ice  Adjust FREEZER 
Control 1° lower
REFRIGERATOR too cold Adjust REFRIGERATOR 
Control 1° higher
FREEZER too cold Adjust FREEZER 
Control 1° higher 
						

							9
2.Use the Freezer (+) or (-) touch pads to scroll through the 
preference names. When the desired preference name is 
displayed, press the Refrigerator (+) or (-) touch pads to 
change the preference status.
3.Set your preferences by pressing and holding the Door Alarm 
touch pad for 3 seconds, or by shutting the refrigerator 
compartment door. 
Crisper Humidity Control 
You can control the amount of humidity in the moisture-sealed 
crisper. Depending on your model, adjust the control to any 
setting between FRUIT and VEGETABLES or LOW and HIGH.
FRUIT / LOW (open) for best storage of fruits and vegetables with 
skins. 
VEGETABLES / HIGH (closed) for best storage of fresh, leafy 
vegetables. 
Ice Maker
IMPORTANT: Flush the water system before turning on the ice 
maker. See “Water Dispenser.” 
Turning the Ice Maker On/Off
To turn the ice maker ON, simply lower the wire shutoff arm.
To manually turn the ice maker OFF, lift the wire shutoff arm to the 
OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made, 
the ice cubes will fill the ice storage bin and the ice cubes will 
raise the wire shutoff arm to the OFF (arm up) position. Do not 
force the wire shutoff arm up or down.
Auto Ice Storage Bin
Your ice storage bin has a lever which allows the storage bin to 
slide out with the drawer when it is pulled open or to stay in place.
■Move the lever to the right to attach the ice storage bin to the 
freezer drawer.   
■Move the lever to the left to release the ice storage bin from 
the freezer drawer.
Ice Production Rate
■The ice maker should produce a complete batch of ice 
approximately every 3 hours. 
■To increase ice production, lower the freezer and refrigerator 
temperature. See “Using the Controls.” Wait 24 hours 
between adjustments. 
Remember
■Allow 24 hours to produce the first batch of ice. Discard the 
first three batches of ice produced.
■The quality of your ice will be only as good as the quality of the 
water supplied to your ice maker. Avoid connecting the ice 
maker to a softened water supply. Water softener chemicals 
(such as salt) can damage parts of the ice maker and lead to 
poor quality ice. If a softened water supply cannot be avoided, 
make sure the water softener is operating properly and is well 
maintained.
■Do not store anything on top of the ice maker or in the ice 
storage bin.
Water Dispenser
IMPORTANT:
■After connecting the refrigerator to a water source or replacing 
the water filter, flush the water system. Use a sturdy container 
to depress and hold the water dispenser lever for 5 seconds, 
then release it for 5 seconds. Repeat until water begins to 
flow. Once water begins to flow, continue depressing and 
releasing the dispenser paddle (5 seconds on, 5 seconds off) 
until a total of 4 gal. (15 L) has been dispensed. This will flush 
air from the filter and water dispensing system, and prepare 
the water filter for use. Additional flushing may be required in 
some households. As air is cleared from the system, water 
may spurt out of the dispenser. 
NOTE: After 5 minutes of continuous dispensing, the 
dispenser will stop dispensing water to avoid flooding. To 
continue dispensing, press the dispenser paddle again. 
■Allow 24 hours for the refrigerator to cool down and chill 
water. Dispense enough water every week to maintain a fresh 
supply.
Dispensing Water
1.Hold a container under the dispenser spout while pressing the 
dispenser pad.
2.Release the dispenser pad to stop dispensing.
Water Filtration System
The water filter is located in the upper right-hand corner of the 
refrigerator compartment. 
 Water Filter Status Lights
The water filter status lights will help you know when to change 
the water filter. When the Order light is on, it is almost time to 
change the water filter. When the Replace light is on, a new water 
filter should be installed. 
After replacing the water filter, press and hold Filter Reset for 
3 seconds until the Order or Replace light turns off. See “Using 
the Controls.”
A. Ice storage bin lever
A
ADo not use with water that is microbiologically unsafe or 
of unknown quality without adequate disinfection before 
or after the system. Systems certified for cyst reduction 
may be used on disinfected waters that may contain 
filterable cysts. 
						

							10
Replacing the Water Filter
To purchase a replacement water filter, model 67003523 Part 
Number 4396395, contact your dealer or call 1-800-442-9991 
U.S.A. or 1-800-807-6777 Canada.
IMPORTANT: Air trapped in the water system may cause water 
and filter to eject. Always dispense water for at least 2 minutes 
before removing the filter or blue bypass cap. 
1.Turn filter counterclockwise to remove.
2.Remove sealing label from replacement filter and insert the 
filter end into the filter head.
3.Turn the filter clockwise until it stops. Snap the filter cover 
closed.
4. Flush the water system. Depending on your model, see 
“Water Dispenser” or “Water and Ice Dispensers.”
NOTE: The dispenser feature may be used without a water filter 
installed. Your water will not be filtered. If this option is chosen, 
replace the filter with the blue bypass cap.
REFRIGERATOR CARE
Cleaning
Both the refrigerator and freezer sections defrost automatically. 
However, clean both sections about once a month to avoid 
buildup of odors. Wipe up spills immediately.
IMPORTANT: Because air circulates between both sections, any 
odors formed in one section will transfer to the other. You must 
thoroughly clean both sections to eliminate odors. To avoid odor 
transfer and drying out of food, wrap or cover foods tightly.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window 
sprays, scouring cleansers, flammable fluids, cleaning waxes, 
concentrated detergents, bleaches or cleansers containing 
petroleum products on plastic parts, interior and door liners or 
gaskets. Do not use paper towels, scouring pads, or other harsh 
cleaning tools.
1.Unplug refrigerator or disconnect power.
2.Hand wash, rinse, and dry removable parts and interior 
surfaces thoroughly. Use a clean sponge or soft cloth and a 
mild detergent in warm water. 
3.Wash stainless steel and painted metal exteriors with a clean 
sponge or soft cloth and a mild detergent in warm water. 
■To keep your stainless steel refrigerator looking like new 
and to remove minor scuffs or marks, it is suggested that 
you use the manufacturer’s approved Stainless Steel 
Cleaner and Polish, Part Number 4396920. To order the 
cleaner, call 1-800-442-9991 U.S.A. or 1-800-807-6777 
Canada.IMPORTANT: This cleaner is for stainless steel parts only!
Do not allow the Stainless Steel Cleaner and Polish to come 
into contact with any plastic parts such as the trim pieces, 
dispenser covers or door gaskets. If unintentional contact 
does occur, clean plastic part with a sponge and mild 
detergent in warm water. Dry thoroughly with a soft cloth.
4.There is no need for routine condenser cleaning in normal 
home operating environments. If the environment is 
particularly greasy or dusty, or there is significant pet traffic in 
the home, the condenser should be cleaned every 2 to 
3 months to ensure maximum efficiency.
If you need to clean the condenser:
■Remove the base grille.
■Use a vacuum cleaner with a soft brush to clean the grille, 
the open areas behind the grille and the front surface area 
of the condenser.
■Replace the base grille when finished.
5.Plug in refrigerator or reconnect power.
Changing the Light Bulb
NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to 
replace the bulb with an appliance bulb of the same size, shape, 
and wattage (no greater than 40 watts).
Changing the Refrigerator Light Bulb
1.Unplug the refrigerator or disconnect power.
2.Slide the light shield toward the back of the compartment to 
release it from the light assembly. 
3.Replace burned-out bulb(s) with appliance bulb(s) no greater 
than 40 watts.
4.Replace the light shield by inserting the tabs on the shield into 
the liner holes on each side of light assembly. Slide the shield 
toward the front until it locks into place.
NOTE: To avoid damaging the light shield, do not force the 
shield beyond the locking point.
5.Plug in refrigerator or reconnect power.
Changing the Freezer Light Bulb
1.Unplug refrigerator or disconnect power.
2.Remove the burned-out bulb and replace it with an appliance 
bulb no greater than 40 watts.
3.Plug in refrigerator or reconnect power.
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.