Home > Kenwood > Communications receiver > Kenwood Ts-2000x All Mode Multi-band Transceiver Service Manual

Kenwood Ts-2000x All Mode Multi-band Transceiver Service Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Kenwood Ts-2000x All Mode Multi-band Transceiver Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 176 Kenwood manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 171
    Add page 101 to Favourites
    image text
    Enable zoom 
    							102
TS-2000/X
No. Adjustment item ItemFrequencyMode
33 FM S-full scale FM full 50.2M FM
34 SSB IF gain SSB start 144.2M USB
35 SSB S1 SSB S1 144.2M USB
36 SSB S9 SSB S9 144.2M USB
37 SSB S-full scale SSB S full 144.2M USB
38 FM S1 FM S1 145.8M FM
39 FM full scale FM full 145.8M FM
40 FM S1 (SUB) FM S1 145.8M FM
41 FM full scale (SUB) FM full 145.8M FM
42 AM S1 AM S1 120.2M AM
43 AM S-full scale AM full 120.2M AM
44 SSB IF gain SSB start 438.2M USB
45 SSB S1 SSB S1 438.2M USB
46 SSB S9 SSB S9 438.2M USB
47 SSB S-full scale SSB S full 438.2M USB
48 FM S1 FM S1 438.2M FM
49 FM S-full scale FM full 438.2M FM
50 FM S1 (SUB) FM S1 438.2M FM
51 FM S-full scale (SUB) FM full 438.2M FM
52 SSB IF gain SSB start 1270.2M USB
53 SSB S1 SSB S1 1270.2M USB
54 SSB S9 SSB S9 1270.2M USB
55 SSB S-full scale SSB S full 1270.2M USB
56 FM S1 FM S1 1270.2M FM
57 FM S-full scale FM full 1270.2M FM
58 ALT voltage Center 1270.2M FM
59 ALT voltage Center 145.8M FM
60 SQ threshold voltage FM 50.2M FM
61 SQ threshold voltage FM 145.8M FM
62 SQ tight voltage (144M) FM 145.8M FM
63SQ threshold voltage (144M)FM 145.8M FM
64 SQ tight voltage (144M) FM 145.8M FM
65SQ threshold voltage (430M)FM 438.2M FM
66SQ threshold voltage (430M)FM 438.2M FM
67SQ threshold voltage (1200MHz)FM 1270.2M FM
68 Power (POC)/Power meter100W/20W14.1M USB
69 Power (POC)/Power meter 50W/10W 14.1M USB
70 Power (POC)/Power meter 25W/5W 14.1M USB
71 Power (POC)/Power meter 10W/2W 14.1M USB
72 Power (POC)/Power meter 5W/1W 14.1M USB
73 TX gain for band 1.8M 1.83M USB
74 TX gain for band 3.5M 3.51M USB
75 TX gain for band 7M 7.01M USB
76 TX gain for band 10M 10.1M USB
77 TX gain for band 14M 14.1M USB
78 TX gain for band 18M 18.1M USB
79 TX gain for band 21M 21.1M USB
80 TX gain for band 24M 24.9M USB
81 TX gain for band 28M 28.1M USB
82 TX gain for band 52M 50.1M USB
83 HF TX gain for power 50W/10W 14.1M USB
84 HF TX gain for power 25W/5W 14.1M USB
85 HF TX gain for power 10W/2W 14.1M USB
No. Adjustment item ItemFrequencyMode
86 HF TX gain for power 5W/1W 14.1M USB
87 ALC meter start Start 14.1M USB
88 ALC meter zone max Zone max 14.1M USB
89 FM modulation deviation Wide dev 29.1M FM
90 FM modulation deviationNarrow dev29.1M FM
91Power (POC) / Power meter100W/20W145.9M USB
92Power (POC) / Power meter50W/10W 145.9M USB
93Power (POC) / Power meter25W/5W 145.9M USB
94Power (POC) / Power meter10W/2W 145.9M USB
95Power (POC) / Power meter5W/1W 145.9M USB
96 TX gain for band 146M 145.9M USB
97 144M TX gain for power 50W/10W 145.9M USB
98 144M TX gain for power 25W/5W 145.9M USB
99 144M TX gain for power 10W/2W 145.9M USB
100 144M TX gain for power 5W/1W 145.9M USB
101Power (POC) / Power meter50W/20W 438.1M USB
102Power (POC) / Power meter25W/10W 438.1M USB
103Power (POC) / Power meter12.5W/5W 438.1M USB
104Power (POC) / Power meter5W/1W 438.1M USB
105 TX gain for band 440M 438.1M USB
106 440M TX gain for power 25W/10W 438.1M USB
107 440M TX gain for power 12.5W/5W 438.1M USB
108 440M TX gain for power 5W/1W 438.1M USB
109Power (POC) / Power meter10W 1270.1M USB
110Power (POC) / Power meter5W 1270.1M USB
111Power (POC) / Power meter2.5W 1270.1M USB
112Power (POC) / Power meter1W 1270.1M USB
113 TX gain for 1.2G band 1.2G 1240.1M USB
114 TX gain for band 1.2G 1270.1M USB
115 TX gain for 1.2G band 1.2G 1299.9M USB
116 1.2G TX gain for power 2.5W 1270.1M USB
117 1.2G TX gain for power 1W 1270.1M USB
118 SWR protection HF 14.1M CW
119 SWR meter (VSWR : 3.0) 14M 14.1M FM
120 SWR meter (VSWR : 3.0) 52M 50.1M CW
121 SWR protection 146M 145.9M CW
122 SWR protection 440M 438.1M CW
123 SWR protection 1270.1 1270.1M CW
124 EEPROM write
125 Checksum
126 Display check / Activate all
the AT relay contacts
You can confirm the settings of Menu No. 125 and 126
even if you are not in the adjustment mode.
Menu No. 125 checksum display
ADJUSTMENT
Main CPUDSP1
DSP2
    Add page 102 to Favourites
    image text
    Enable zoom 
    							103
ADJUSTMENT
Measurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
TS-2000/X
Display Check
1. All reset 1) DC IN : 13.8V Front LCD After displaying Display should be normal.
Hold down [A=B] key and panel “HELLO”, the Should be at the reset
press the [POWER]key. display is reset as frequency.
follows;
Main band side
DISP f. : 14.000.00
Mode : USB
ANT1, PTT, CTRL,
AGC, PRE
Sub band side
DISP f. : 144.000.00Mode : FM
PRE, TNC
2. LCD all 1) Menu No. : 126 Check LCD all segments light.
segments
light
PLL Section
1. 31.2MHz 1) Display f. : 14.100MHzOscilloscopeTX-RX2 W503 TX-RX2 L422 Level max. –3dBm or more
level Mode : USB (B/11) (B/11) L427
Receive
2. Lock voltage 1) HF REF VCO DC V.M TP501 TX-RX2 TC403 1.5V±0.5V
Display f. : 2.000MHz Spectrum (D/11)
Mode : FM analyzer
Display f. : 12.990MHz Check 4.6V or less
2) HF1 MAIN PLL TP502 TX-RX2 TC408 1.45V±0.05V
Display f. : 30.00kHz (J/11)
Mode : FM
Display f. : 16.990MHz Check 6.3V or less
3) HF2 MAIN PLL TX-RX2 TC410 1.45V±0.05V
Display f. : 17.00MHz (J/11)
Mode : FM
Display f. : 36.990MHz Check 6.3V or less
4) HF3 MAIN PLL TX-RX2 TC409 1.45V±0.05V
Displat f. : 37.00MHz (J/11)
Mode : FM
Display f. : 60.000MHz Check 6.3V or less
5) HF LO2 PLL TX-RX2 TP505 TX-RX2 TC402 1.5V±0.05V
Display f. : 24.00MHz (C/11) (I/11)
Mode : FM
Display f. : 29.000MHz Check 4.6V or less
6) VHF REF PLL TX-RX2 TP512 TX-RX2 TC406 2.0V±0.5V
Display f. : 142.00MHz (B/11) (E/11)
Mode : FM
Display f. : 151.990MHz Check 4.6V or lessMeasurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
    Add page 103 to Favourites
    image text
    Enable zoom 
    							ADJUSTMENT
Measurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
104
TS-2000/X
7) VHF MAIN PLL DC V.M TX-RX2 TP503 TX-RX2 TC405 1.0V±0.03V
Display f. : 142.00MHz Spectrum (B/11) (H/11)
Mode : FM analyzer
Display f. : 152.000MHz Check 4.6V or less
8) UHF PLL TP504 TX-RX2 TC404 6.0V±0.05V
Display f. : 449.990MHz (G/11)
Mode : FM
Display f. : 420.000MHz Check 1.5V or more
9) SUB1 PLL TX-RX2 TP506 TX-RX2 TC400 5.5V±0.2V
Display f. : 154.495MHz (C/11) (K/11)
Mode : FM
Display f. : 220.000MHz Check 1.0V or less
10) SUB2 PLL TX-RX2 TC401 5.5V±0.5V
Display f. : 173.995MHz (K/11)
Mode : FM
Display f. : 135.000MHz Check 1.0V or less
Receiver Section
1. HF BPF 1) Display f. : 7.200MHz Tracking Rear ANT1 TX-RX1 L23 Adjust the coils to
Mode : AM generator panel (A/9) L24 obtain the frequency
Spectrum analyzer setting L25 response as shown.
Center f. : 7.000MHz Spectrum TX-RX1 CN5
Frequency span : 5MHz analyzer (A/9)
XdB/DIV : 10dB
RBW : 30kHz
VBW : 30kHz
2) Display f. : 14.200MHz L32
Spectrum analyzer setting L33
Center f. : 14.000MHz L34
3) Display f. : 50.000MHz L45
Spectrum analyzer setting L46
Center f. : 54.000MHz
L44 Adjust the coil to
get a null point at
68.985MHz as
shown.
2. RX trap 1) Display f. : 11.700MHz TC1 Adjust the trimmer
Mode : AM to get a null point at
(E type only) PRE-AMP : ON 11.7MHz.
2) Display f. : 15.501MHz TC2 Adjust the trimmer
to get a null point at
15.501MHz. Measurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
7.000
(MHz)
14.000
(MHz)
54.000
68.985
(MHz)
    Add page 104 to Favourites
    image text
    Enable zoom 
    							105
ADJUSTMENT
Measurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
TS-2000/X
3. MCF 1) Display f. : 14.000MHz Tracking Rear ANT1 TX-RX1 L54 Adjust the coils to
(69.085MHz) Mode : USB generator panel (A/9) L62 obtain the frequency
PRE-AMP : ON L63 response as shown.
AGC : OFF Spectrum TX-RX1 TP4 L64
Spectrum analyzer setting analyzer (A/9) (CN6) L68
Center f. : 69.085MHz TP5
Frequency span : 100kHz (CN9)
XdB/DIV : 10dB
RBW : 30kHz
VBW : 30kHz
4. MCF 1) Display f. : 18.000MHz L65
(72.925MHz) Spectrum analyzer setting L66
Center f. : 72.925MHz L67
• Perform the following in the adjustment mode. Item 5, 6, 10~12, 16, 17 and 21~38.
   To terminate the adjustment menu in the middle, save your settings with Menu No. 124.
5. MAIN 1) Sub band f. : 144.000MHz Tracking Rear ANT144 TX-RX2 L163 Adjust the coils to
VHF BPF Mode : USB generator panel (A/11) L164 obtain the frequency
PRE-AMP : ON response as shown.
AGC : ON Spectrum TX-RX2 CN19
Spectrum analyzer setting analyzer (A/11)
Center f. : 146.000MHz
Frequency span : 50MHz
XdB/DIV : 5dB
RBW : 100kHz
VBW : 30kHz
2) Menu No. : 01 CN15 Front [+] key After setting the
Display f. : 146MHz panel or adjustment value to
[–] key 160, adjust each coil
TX-RX2 L23 to obtain the fre-
(A/11) L34 quency response as
L47 shown.
L55
3) Menu No. : 02 Front [+] key Change the adjust-
Display f. : 142MHz panel or ment values to get
[–] key the highest peak
points as shown.
4) Menu No. : 03
Display f. : 144MHz
5) Menu No. : 04
Display f. : 148MHz
6) Menu No. : 05
Display f. : 152MHz
69.085
(MHz)
72.925
(MHz)
(MHz)
146
152 142
146MHz
142MHz
144MHz
148MHz
152MHz
    Add page 105 to Favourites
    image text
    Enable zoom 
    							ADJUSTMENT
Measurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
106
TS-2000/X
6. MAIN 1) Trap default Tracking Rear ANT430 TX-RX2 TC9 Adjust the trimmer
UHF BPF generator panel (A/11) to get a null point at
366MHz as shown.
Spectrum TX-RX2 CN19
analyzer (A/11)
2) Menu No. : 06 Front [+] key After setting the
Display f. : 440MHz panel or adjustment value to
Spectrum analyzer setting [–] key 145, adjust each
Center f. : 440.000MHz TX-RX2 TC1 trimmer to obtain
Frequency span : 100MHz (A/11) TC2 the frequency
XdB/DIV : 5dB TC3 response as shown.
RBW : 100kHz
VBW : 30kHz
3) Menu No. : 07 Front [+] key Change the adjust-
Display f. : 449.8MHz panel or ment values to get
[–] key the highest peak
points as shown.
4) Menu No. : 08
Display f. : 430MHz
5) Menu No. : 09
Display f. : 420MHz
7. HF RX 1) Display f. : 14.201MHz SSG Rear ANT1 TX-RX1 L69 AF output max.
IF gain Mode : USB panel (A/9) L71
PRE-AMP : OFF
OscilloscopeEXT. SP L613
AF output : 0.63V/8ΩAF V.M L614
SSG f. : 14.201MHz DM. SP L87
SSG output : –113dBm/0.501µV
8. 1st mixer 1) Display f. : 100kHz VR1 Noise min.
balance Mode : USB
PRE-AMP : OFF
SSG output : OFF
9. Gain balance 1) Display f. : 9.000MHz VR4 Set the AF output
Mode : USB voltage to 0.63V at
SSG f. : 9.001MHz 8,999.99kHz. Then
SSG output : –116dBm/0.35µVadjust VR4 to obtain
the voltage 0.63V at
9.000MHz when the
transceiver is in the
receive mode.
(If you would not
get the specified
voltage, adjust
3. MCF and
4. MCF again.)
440MHz
449.8MHz
430MHz
420MHz
366MHz
    Add page 106 to Favourites
    image text
    Enable zoom 
    							107
ADJUSTMENT
Measurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
TS-2000/X
10. 10.695MHz 1) Menu No. : 20 SSG1 Rear ANT2 Front [+] key Change the adjust-
IF filter SSG1 f. : 1.8330MHz SSG2 pnel panel or ment values to get
SSG1 output : –33dBm/5010µV2 signal pad[–] key the waveform as
SSG2 f. : 1.8301MHz shown.
SSG2 output : –33dBm/5010µVOscilloscopeTX-RX1 TP1
Disconnect the cable from (A/9)
CN23.
11. 455kHz 1) Menu No. : 21 TP2
IF filter Connect the cable to CN23.
12. SSB IF gain 1) Menu No. : 22 SSG ANT1 Change the adjust-
(AGC start Display f. : 14.201MHz ment values within
level) Mode : USB the range of 1 to 5
SSG output : –110dBm/0.707µVon the display.
2) Menu No. : 28
Display f. : 50.201MHz
SSG outut : –114dBm/0.446µV
13. NB gain 1) Display f. : 14.200MHz DC V.M TX-RX1 TPNB TX-RX1 L81 Voltage min.
Mode : USB (A/9) (A/9) L82
PRE-AMP : ON SSG Rear ANT1
SSG f. : 14.200MHz panel
SSG output : –103dBm/1.58µVAF V.M EXT. SP
AGC : ONOscilloscopeNB : ON DM. SP
Noise G.
2) NB : OFF→ON Adjust output of Noise should disappear
noise generator to when NB is on.
S1 and S9, and
check each.
14. FM 1) Display f. : 29.2MHz TX-RX1 L83 AF distortion min. 3% or less
discriminator Mode : FM (A/9)
coil (HF) AF output : 0.63V/8Ω
SSG f. : 29.2MHz
SSG output : –53dBm/501µV
MOD : 1kHz
DEV : 3kHz
15. RX IF gain 1) Display f. : 145.991MHz SSG Rear ANT144 TX-RX2 L80 AF output max.
(VHF) Mode : USB panel (A/11) L82
AF output : 0.63V/8Ω
OscilloscopeEXT. SP L86
SSG f. :145.991MHz AF V.M
SSG output : –120dBm/0.22µVDM. SP
16. SSB IF gain 1) Menu No. : 34 Front [+] key Change the adjust-
(AGC start Display f. : 144.201MHz panel or ment values within
level) Mode : USB [–] key the range of 1 to 5
SSG output : –116dBm/0.35µVon the display.
2) Menu No. : 44 ANT430
Display f. : 438.20MHz
SSG output : –116dBm/0.35µV
SSG12 signal pad
SSG2ANT
    Add page 107 to Favourites
    image text
    Enable zoom 
    							ADJUSTMENT
Measurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
108
TS-2000/X
17. Sub band 1) Menu No. : 10 SSG Rear ANT144 TX-RX2 L28 After setting the S-meter voltage max.
BPF Display f. : 146MHz panel (A/11) L44 adjustment value to
Mode : FM
OscilloscopeEXT. SP L52 90, adjust each coilSSG output : –110dBm/0.707µVAF V.M to obtain the
MOD : 1kHz DM. SP TX-RX2 SSM specified values.
DEV : 3kHz (A/11)
2) Menu No. : 11 Front [+] key Change the adjust- (1.04V)
Display f. : 118MHz panel or ment values to have
Mode : FM [–] key the highest readings
MOD : 1kHz of S-meter voltage.
DEV : 3kHz
3) Menu No. : 12(1.13V)
Display f. : 132MHz
Mode : FM
MOD : 1kHz
DEV : 3kHz
4) Menu No. : 13(1.17V)
Display f. : 160MHz
Mode : FM
MOD : 1kHz
DEV : 3kHz
5) Menu No. : 14(1.11V)
Display f. : 174MHz
Mode : FM
MOD : 1kHz
DEV : 3kHz
18. FM 1) Display f. : 145.800MHz DC V.M TX-RX2 CN1 TX-RX2 L93 AF output max.
discriminator Mode : FM (A/11) (A/11)
coil AF output : 0.63V/8ΩSSG Rear ANT144
(VHF) SSG f. : 145.800MHz panel Check the AF 3% or less
Sub band SSG output : –53dBm/501µV AF V.M EXT. SP distortion
MOD : 3kHz
OscilloscopeDM. SP
19. Trap 1) SSG1 f. : 439.8MHz ANT430 TX-RX TC9 SINAD max.
frequency Mode : FM (A/11)
(UHF)
SSG1 output : –108dBm/0.9µVMOD : 1kHz
DEV : 3kHz
SSG2 f. : 356.01MHz
Mode : FM
SSG2 output : –30dBm/7070µVMOD : 400Hz
DEV : 3kHz
20. S/N check 1) Display f. : Next page SSG Rear ANT
(Reference) AF output : 0.63V/8Ωpanel
AGC : FAST AF V.M EXT. SP
SSG f. : Next page
OscilloscopeHowever, USB : +1kHz Distortion
PRE-AMP : ON meter
ATT : OFF DM. SP
    Add page 108 to Favourites
    image text
    Enable zoom 
    							109
ADJUSTMENT
Measurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
TS-2000/X
Band Frequency (K) Frequency (E) ModeSSG RF level (dBm)SSG MOD DEVMeasurementSpec.
MAIN 550kHz 550KHz AM –85 1kHz60%→OFFS/N >10dB
MAIN 14.200MHz 14.200MHz USB –119→OFF OFF OFF S/N >10dB
MAIN 18.200MHz 18.200MHz USB –119→OFF OFF OFF S/N >10dB
MAIN 52.200MHz 52.200MHz FM –118 1kHz 3kHz SINAD >12dB
MAIN 146.200MHz 145.200MHz AM –106 1kHz60%→OFFS/N >10dB
MAIN 146.200MHz 145.200MHz FM –121 1kHz 3kHz SINAD >12dB
SUB 118.200MHz – AM –85 1kHz60%→OFFS/N >10dB
SUB 146.200MHz 145.200MHz FM –117 1kHz 3kHz SINAD >12dB
MAIN 440.200MHz 435.200MHz FM –122 1kHz 3kHz SINAD >12dB
MAIN 430.200MHz 430.200MHz FM –121 1kHz 3kHz SINAD >12dB
MAIN 449.200MHz 439.200MHz FM –121 1kHz 3kHz SINAD >12dB
SUB 444.200MHz 430.200MHz FM –117 1kHz 3kHz SINAD >12dB
SUB 438.200MHz 435.200MHz FM –117 1kHz 3kHz SINAD >12dB
SUB 449.200MHz 439.200MHz FM –117 1kHz 3kHz SINAD >12dB
21. SSB 1) Menu No. : 23 SSG Rear ANT1 Front [+] key 1 push S-meter lights up to S1 level.
S-meter Display f. : 14.201MHz panel panel or
S1 (HF) Mode : USB AF V.M EXT. SP [–] key
AGC : ON
OscilloscopePRE-AMP : ON DM. SP
SQL : Counterclockwise max.
(Level min.)
RF GAIN : Clockwise max.
SSG f. : 14.201MHz
SSG output : –107dBm/1µV
S9 2) Menu No. : 24S-meter lights up to S9 level.
SSG output : –81dBm/19.9µV
Full scale 3) Menu No. : 25S-meter lights up all.
(Lights up all)SSG output : –21dBm/19900µV
22. FM 1) Menu No. : 26S-meter lights up to S1 level.
S-meter Display f. : 29.2MHz
S1 (HF) Mode : FM
SSG f. : 29.2MHz
SSG output : –117dBm/0.316µVMOD : 1kHz
DEV : 3kHz
Full scale 2) Menu No. : 27S-meter lights up all.
(Lights up all)SSG output : –95dBm/3.98µV
23. 50MHz 1) Menu No. : 29S-meter lights up to S1 level.
SSB S-meter Display f. : 50.2MHz
S1 Mode : USB
SSG output : –111dBm/0.63µV
S9 2) Menu No. : 30S-meter lights up to S9 level.
SSG output : –85dBm/12.6µV
Full scale 3) Menu No. : 31S-meter lights up all.
(Lights up all)SSG output : –25dBm/12600µV
    Add page 109 to Favourites
    image text
    Enable zoom 
    							ADJUSTMENT
Measurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
110
TS-2000/X
24. 50MHz FM 1) Menu No. : 32 SSG Rear ANT1 Front [+] key 1 push S-meter lights up to S1 level.
S-meter Display f. : 50.2MHz panel panel or
S1 Mode : FM AF V.M EXT. SP [–] key
SSG output : –117dBm/0.316µVOscilloscopeMOD : 1kHz DM. SP
DEV : 3kHz
Full scale 2) Menu No. : 33S-meter lights up all.
(Lights up all)SSG output : –95dBm/3.98µV
25. 144MHz 1) Menu No. : 35 ANT144 S-meter lights up to S1 level.
SSB S-meter Display f. : 144.2MHz
S1 Mode : USB
SSG output : –113dBm/0.501µV
S9 2) Menu No. : 36S-meter lights up to S9 level.
SSG output : –93dBm/5.01µV
Full scale 3) Menu No. : 37S-meter lights up all.
(Lights up all)SSG output : –43dBm/1580µV
26. 144MHz 1) Menu No. : 38S-meter lights up to S1 level.
FM S-meter Display f. : 145.8MHz
S1 Mode : FM
SSG output : –117dBm/0.316µVMOD : 1kHz
DEV : 3kHz
Full scale 2) Menu No. : 39S-meter lights up all.
(Lights up all)SSG output : –95dBm/3.98µV
27. 120MHz 1) Menu No. : 42S-meter lights up to S1 level.
SUB AM Display f. : 120.2MHz
S-mete Mode : AM
S1
SSG output : –105dBm/1.26µVMOD : 1kHz
DEV : 60%
Full scale 2) Menu No. : 43S-meter lights up all.
(Lights up all)SSG output : –85dBm/12.6µV
28. 144MHz 1) Menu No. : 40S-meter lights up to S1 level.
SUB FM Display f. : 145.8MHz
S-mete Mode : FM
S1
SSG output : –117dBm/0.316µVMOD : 1kHz
DEV : 3kHz
Full scale 2) Menu No. : 41S-meter lights up all.
(Lights up all)SSG output : –95dBm/3.98µV
29. 440MHz 1) Menu No. : 45 ANT430 S-meter lights up to S1 level.
SSB S-meter Display f. : 438.2MHz
S1 Mode : USB
SSG output : –113dBm/0.501µV
S9 2) Menu No. : 46S-meter lights up to S9 level.
SSG output : –93dBm/5.01µV
Full scale 3) Menu No. : 47S-meter lights up all.
(Lights up all)SSG output : –43dBm/1580µV
    Add page 110 to Favourites
    image text
    Enable zoom 
    							111
ADJUSTMENT
Measurement
Test-
equipmentUnitTerminalAdjustment
Unit Parts MethodSpecifications/Remarks Condition
Item
TS-2000/X
30. 440MHz 1) Menu No. : 48 SSG Rear ANT430 Front [+] key 1 push S-meter lights up to S1 level.
FM S-meter Display f. : 438.2MHz panel panel or
S1 Mode : FM AF V.M EXT. SP [–] key
SSG output : –117dBm/0.316µVOscilloscopeMOD : 1kHz DM. SP
DEV : 3kHz
Full scale 2) Menu No. : 49S-meter lights up all.
(Lights up all)SSG output : –95dBm/3.98µV
31. 440MHz 1) Menu No. : 50S-meter lights up to S1 level.
SUB FM Display f. : 438.2MHz
S-mete Mode : FM
S1
SSG output : –117dBm/0.316µVMOD : 1kHz
DEV : 3kHz
Full scale 2) Menu No. : 51S-meter lights up all.
(Lights up all)SSG output : –95dBm/3.98µV
32. 144MHz 1) Menu No. : 61 ANT144
FM SQL Display f. : 145.8MHz
threshold Mode : FM
SSG output : OFF
MOD : 1kHz
DEV : 3kHz
33. 144MHz 1) Menu No. : 62
FM SQL Display f. : 145.8MHz
tight Mode : FM
SSG output : –113dBm/0.501µVMOD : 1kHz
DEV : 3kHz
34. 144MHz 1) Menu No. : 63
sub band Display f. : 145.8MHz
FM SQL Mode : FM
threshold SSG output : OFF
MOD : 1kHz
DEV : 3kHz
35. 144MHz 1) Menu No. : 64
sub band Display f. : 145.8MHz
FM SQL Mode : FM
tight
SSG output : –113dBm/0.501µVMOD : 1kHz
DEV : 3kHz
36. 50MHz 1) Menu No. : 60 ANT1
FM SQL Display f. : 50.2MHz
threshold Mode : FM
SSG output : OFF
MOD : 1kHz
DEV : 3kHz
37. 430MHz 1) Menu No. : 66 ANT430
FM SQL Display f. : 438.2MHz
threshold Mode : FM
SSG output : OFF
MOD : 1kHz
DEV : 3kHz
    All Kenwood manuals Comments (0)

    Related Manuals for Kenwood Ts-2000x All Mode Multi-band Transceiver Service Manual