JVC Projector Dla X500r Instructions Manual

Adjusting the Position
Adjusting the elevation angle of the projector
The height and inclination of the unit (0 to 5 mm) can be
adjusted by turning the feet.
Lift the unit and adjust the four feet.
. Adjusting the position of the image
By using the lens shift feature of this unit, you can shift
the image upward/downward or to the left/right. Set it to
your preferred position. Æ “Adjusting the Lens According to the Projection
Position”  （p. 27
）
. 0
The maximum vertical shift varies with the amount of...

Connecting the Projector
0 Do not turn on the power until connection is complete.
0 The connection procedures differ according to the device used. For details, please refer to the instruction manual
of the device to be connected.
0 This projector is used for projecting images. To output the audio of connected devices, please connect a separate
audio output device, such as an amplifier or speaker.
0 The images may not be displayed depending on the devices and cables to be connected.
Use only HDMI cables...

Connecting to the LAN Terminal
. 0The network is used to control this unit. It is not used for sending or receiving video signals.
0Please contact your network administrator for information concerning the network connection.
0Set “ECO Mode” to “Off” if RS-232C/LAN communication is performed or the HDMI link function is used in the Standby
mode. (p. 59)
0For more information on control, please refer to “External Control” (p. 70).
Connecting to the RS-232C Terminal
. 0
Set “ECO Mode” to “Off” if...

Connecting to the TRIGGER Terminal
. 0
Do not use it to supply power to other devices.
0 Connecting to the audio terminal of another device may cause the device to malfunction or break down.
0 Using beyond the rated value will cause the unit to malfunction.
0 The trigger terminal outputs a voltage of 12 V. Exercise adequate caution to prevent short circuit.
0 The factory setting is “Off”. To change the setting, configure the “Trigger” item in the menu ( p. 59).Connecting the Power Cord (Supplied...

Viewing Videos
MEMO
0 When you are using  Q, be sure to remove the lens cover.
0 Connect the power cord, and ensure that the “STANDBY/ON” indicator
lights up in red. 1
Turn on the power
Remote control: press the  C [ON] button
Projector unit: press the  A [STANDBY/ON] button
0 The “STANDBY/ON” indicator light  switches 
from red to green (light
goes off after the unit starts up).
0 (S R) The motorized lens cover opens.
. 2
Choose the image to project
Pressing the [INPUT] button on the projector unit or...

3
Turn off the power
Remote control: press the B [STAND BY] button
Projector unit: press the A [STANDBY/ON] button 0 While the “Are you sure you want to turn off?” message is displayed, press the button again.
0 The lamp turns off, and the “STANDBY/ON” indicator switches from a green light to a red blinking light.
0 After the light goes off, the fan will run for about 100 seconds to cool down the lamp (Cool-down mode).
Do not disconnect the power cable while cooling is in progress.
0 After about 100...

Adjusting the Projector Screen
Adjusting the Lens According to the Projection Position
1
Press the [LENS CONTROL] button, and use the
[
JKH I] keys to adjust Focus, Zoom (screen size),
and Shift (screen position)
. 0
Pressing the [LENS CONTROL] or [OK] button each time switches
the mode in the following sequence:
“Focus” "“Zoom” "“Shift”"“Focus”...
. 2
Press the [MENU] button once, or the [BACK] twice,
to end adjustment.
0 Operation of the lens control feature is disabled when the lens lock...

Saving and Retrieving Adjustment Settings
The Focus, Zoom, and Shift settings can be saved or retrieved, so you can
switch easily to a 
different 
aspect ratio (screen size) according to the image.
0 Pressing the [LENS MEMORY]  button 

each time switches the mode in the
following sequence: “Lens Memory Save” "“Lens Memory Select”"“Lens
Memory Name Edit” "“Lens Memory Save”...
0 In a state where no adjustment settings are saved (factory default), only
“Lens Memory Save” is displayed.
0...

Retrieving an adjustment data
1
Press the [LENS MEMORY] button to display “Lens Memory Select”
0 Pressing  the [LENS MEMORY] 
button 
each time switches the mode in the following sequence: “Lens Memory
Select”"“Lens Memory Save” "“Lens Memory Name Edit”"“Lens Memory Select”...
0 You can also retrieve an adjustment data by selecting “Installation” "“Lens Control”"“Lens Memory Select”
from the menu.
.2
Select the adjustment data to retrieve, and press the [OK] button
0 The retrieved...

Adjusting Image Quality Automatically According to the Viewing
Environment
By configuring “Environment Setting” according to the
viewing environment, image quality adjustment and
correction according to environmental differences are
performed  automatically 
to minimize 
any 
influence on the
image quality.
0 “Environment Setting” is applied separately from the
individually adjusted data.
0 Screen correction cannot be performed when “Color
Profile” is set to “x.v.Color”.
.1
Press the [MENU] button to...