JBL Synthesis Sdp-5 Manual

SETUP
SDP-5
3-51
FORMAT
SECAM, PAL, NTSC
Controls the compatibility between the video input connectors, the
video switcher, and the display device. Select the setting that is
compatible with the source components and display device.
Note:The FORMAT parameter affects the composite and
S-video output connectors. It does not affect thecomponent video output connector.
FORMAT


ON-SCREEN DISPLAY


DISPLAYS


SETUP
POSITION
TOP, CENTER, BOTTOM
Controls the vertical position of the two-line status on the...

SETUP
JBL Synthesis
3-52BACKGROUND
ON, OFF
Activates and deactivates the menu background. When set to ON,
on-screen display menus appear over a solid blue or gray
background (depending on the display device). When set to OFF,
on-screen display menus appear over the video input signal. 
Note:When the BACKGROUND parameter is set to OFF, the
on-screen display will disappear if the display deviceis using the component video output connector.
BACKGROUND


ON-SCREEN DISPLAY


DISPLAYS


SETUP
REMOTE STATE
ON,...

SETUP
SDP-5
3-53FRONT PANEL DISPLAY SETUPOpens the FRONT PANEL DISPLAY menu shown above, which can
be used to customize the front panel display.
Default PossibleParameter Setting Settings
STATUS ALWAYS ON ALWAYS ON, 2 SECONDS,
ALWAYS OFF
BRIGHTNESS 75% 100%, 75%, 50%, 25%STATUS
ALWAYS ON, 2 SECONDS, ALWAYS OFF
Activates and deactivates the front panel display. When set to
ALWAYS ON, the front panel display remains on at all times. When
set to 2 SECONDS, the front panel display appears for 2 seconds...

SETUP
JBL Synthesis
3-54VOLUME CONTROL SETUPSelecting the SETUP menu VOLUME CONTROLS option opens the VOLUME CONTROL SETUP menu shown below, which can be used to
configure Main Zone and Zone 2 volume levels.
VOLUME CONTROLS


SETUP
Default Possible
Parameter Setting SettingsMAIN PWR ON -30dB LAST LVL, -80 to +6dB
MUTE LEVEL
FULL MUTE FULL MUTE, -40dB, -30dB, -20dB,
-10dB
ZONE PWR ON -30dB LAST LVL, -80 to +6dBMAIN PWR ON
LAST LVL, -80 to +6dB
Sets the Main Zone volume level that will be selected whenever...

SETUP
SDP-5
3-55 PWR – the power trigger output connector – is not configurable. It is activated when the
SDP-5 is activated, and deactivated when the SDP-5 is deactivated. The trigger output
connector labeled 1 can be configured for remote or program operation.
Default PossibleParameter Setting SettingsREMOTE ONLY OFF ON, OFFProgram Operation N/A ON, OFFAll TRIGGER SETUP menu parameters – except the REMOTE ONLY
parameter – are considered program operation parameters.REMOTE ONLY
ON, OFF
Configures the...

SETUP
JBL Synthesis
3-56 When the REMOTE ONLY parameter is set to OFF and program operation parameters are set to
ON, the trigger output connector labeled 1 is associated with the corresponding Main Zone
input, Main Zone listening modes, or Zone 2 inputs. (The connector cannot be associated with
individual Zone 2 inputs; rather, it can be associated with the Zone 2 inputs as a group.) When
configured for program operation, the connector is activated when the corresponding inputs
and listening modes are...

SETUP
SDP-5
3-57 Default PossibleParameter Setting SettingsMODES UNLOCKED LOCKED, UNLOCKEDAUDIO CNTRL  UNLOCKED LOCKED, UNLOCKEDSETUP UNLOCKED LOCKED, UNLOCKEDMODES
LOCKED, UNLOCKED
Controls MODE ADJUST menu branch settings, which include all
listening mode menu settings. When set to LOCKED, these settings
cannot be adjusted. When set to UNLOCKED, these settings can be
adjusted.
MODES


LOCK OPTIONS


SETUP
AUDIO CNTRL
LOCKED, UNLOCKED
Controls AUDIO CONTROLS menu branch settings. When set to
LOCKED,...

4
AUDIO CONTROLS
AUDIO CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 

BASS
-6.0 to +6.0dB
Controls the amount of low-frequency boost or cut applied to the
Main Zone audio output connectors labeled Front L/R, Center, and
Subwoofer. The graph shown on the left of the next page illustrates
the frequency response of BASS parameter settings.
TREBLE
-6.0 to +6.0dB
Controls the amount of boost or cut applied to the Main Zone
audio output connectors labeled Front L/R and Center. The graph
shown on the right of the next page illustrates the frequency
response of TREBLE parameter...

AUDIO CONTROLS
SDP-5
4-3
10 20 50 100 200 500
1k 2k 5k 10k 20k
Hz
+6.0
+5.5
+5.0
+4.5
+4.0
+3.5
+3.0
+2.5
+2.0
+1.5
+1.0
+0.5
+0.0
-0.5
-1.0
-1.5
-2.0
-2.5
-3.0
-3.5
-4.0
-4.5
-5.0
-5.5
-6.0+0.0BASS Parameter Settings
The BASS parameter (previous page) controls the amount of low-frequency boost or
cut applied to the Main Zone audio output connectors labeled Front L/R, Center, and
Subwoofer.
10 20 50 100 200 500
1k 2k 5k 10k 20k
Hz
+0.0+6.0
+5.5
+5.0
+4.5
+4.0
+3.5
+3.0
+2.5
+2.0
+1.5
+1.0
+0.5
+0.0
-0.5...