JBL Dcr600 2 Manual

11
Connect all components as per the Quick Setup
Guide, or as per the appropriate diagram on
pages 6 through 8 of this manual.
Remove any protective plastic films from the
front panel displays of the DCR600
IIand
DVD600
II.
1. Plug the receiver’s Power Cord binto an
unswitched AC outlet.
2.Press the receiver’s Main Power Switch 1
in so that it latches in and is flush with the
front panel. Note that the 
Power Indicator
3will turn amber, indicating that the unit is
in the Standby mode.
3. Install the...

12
Quick Guide to Using the JBL Cinema ProPack 600II
The DVD600IIcan play discs in the following 
formats:
• Both 5-inch (12cm) and 3-inch (8cm) discs
• CD audio discs         • DTS audio discs
• CD-R audio discs      • CD-RW audio discs   
• DVD movie discs
• VCD video compact discs
• Discs containing MP3 compressed-audio files
However, it cannot play:
• DVD discs with a Region Code other than 
1 or All
• DVD discs using PAL format video
• DVD-ROM data discs
• DVD-RAM discs        • CD-I discs 
• CD-G...

13
You may wish to experiment with surround
modes other than Dolby Digital and DTS using
the DCR600
IIreceiver’s functions. Press the
Surround Mode Selectort7to scroll
through such choices as Dolby Pro Logic II (Music,
Movies or Emulation), Dolby 3Stereo, 5-Channel
Stereo, Hall 1 or 2, Theater, Logic 7 (Cinema or
Music) or Surround Off (Stereo). See page 52 for
descriptions of these modes.
Press the 
Stop Buttononce to enter
Resume mode, in which play will resume from
the point where it was stopped....

14
DCR600IIFront Panel Controls
1Main Power Switch:Press this button to
apply power to the DCR600
II. When the switch
is pressed in, the unit is placed in a Standby
mode, as indicated by the amber 
Power
Indicator
3surrounding the System Power
Control
2. This button MUST be pressed in
to operate the unit. To turn the unit off and
prevent the use of the remote control, this
switch should be pressed until it pops out from
the front panel so that the word “OFF” may be
read at the top of the switch....

15
!Input Source Selector: Press this button
to change the input by scrolling up or down
through the list of input sources. When an
audio source is selected, the last video input
used remains routed to the 
Video 1 Output ›
and Video Monitor Output°. This permits
you to simultaneously view and listen to 
different sources.
@FM Mode Selector: Press this button to
select Auto or Manual tuning. When the but-
ton is pressed so that the 
AUTO Indicator T
lights, the tuner will search for the next station
with...

16
DCR600IIFront Panel Information Display
ABitstream Indicators:When the input is
a digital source, these indicators display the
specific type of data signal. The DCR600
IIwill
also indicate when it detects a digital signal
with a resolution of either 96kHz or 192kHz.
This can occur when the receiver is used with
an external DVD-Audio player or other device
that is capable of transmitting this type of sig-
nal. You should not expect to see these indica-
tors light when using the DVD600
IIas your
source...

17
IMPORTANT NOTES
A. The AC plug connections should always be
the last connections made when installing an
A/V system. When making subsequent connec-
tions to audio source equipment or speakers, 
it is always a good practice to unplug the unit
from the AC wall outlet. This prevents the pos-
sibility of sending audio or transient signals to
the speakers that may damage them.
B. Connect devices as per the Quick Setup
Guide or per pages 6 through 8 of this manual.
C. The DCR600IIoffers both composite and...

18
¤Video 1 Video Inputs:Connect to
PLAY/OUTcomposite or S-Video jacks on a
VCR or other video source. 
‹Video 1 Audio Inputs: Connect jacks to
the 
PLAY/OUTaudio jacks on a VCR or other
video source.
›Video 1 Video Outputs:Connect to
RECORD/INPUTcomposite or S-Video jack on
a VCR or other video receiver. 
fiVideo 1 Audio Outputs:Connect to the
RECORD/INPUTaudio jacks on a VCR or
other video recorder.
flVideo 2 Video Inputs:Connect to
PLAY/OUTcomposite or S-Video jacks on a
VCR or other video source....

19
DVD600IIFront Panel Controls
Main Power Switch:Press this button
to apply power to the DVD600
II. When the
switch is pressed in, the unit is placed in a
Standby mode, as indicated by the amber
Power Indicatorsurrounding the
System Power Control. This button
MUST be pressed in to operate the unit. To
turn the unit off and prevent the use of the
remote control, this switch should be pressed
until it pops out from the front panel so that
the word “OFF” may be read at the top of the
switch.
NOTE: This...

20
DVD600IIFront Panel Information Display 
Disc Type:Lights to show the type of disc
currently being played.
Disc Number:Shows if a disc is loaded
in a tray position. The indicator for the disc in
play flashes. Note that if a disc is added to or
removed from the tray while a disc is playing,
the indicator will not show the change until all
discs are cycled.  
Title:Shows the DVD title number current-
ly playing.
Chapter/Track Number:Shows the 
current chapter (DVD) or current track 
number (CD).
Program...