Inter-Tel Imx/Gmx 416/832 Installation Manual

INTER-TELPRACTICES PROGRAMMING 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE Issue 1, November 1994 
FIGURE 5-2. CUSTOMIZED PROGRAMMING REPORT SAMPLES (Continued) 
TRUNK GROUP REPORTS: 
PROGRAMMING REPORTS - TRUNK GROUP REPORT 
Page 1 
Trunk Group l(Al1 Lines) 
Trunk Group Name: 
Enable Hookflash: Yes 
One-Way Incoming Only: No 
Tenant Group: 
10 
Music-On-Hold: 
Music #l 
Day OutGoing Access 
EXT# CKT# DESCRIPTION USRNAME 
_---__--_--_______-_~~~~~~~~~~--~~~- 
1000 01.01 Station Undefined 
1001 01.02...

PROGRAMMING 
INTRR-TELdPRACTICES 
Issue 1, November 1994 
lMX/GMX 416/832 INSTALLATION & MAINTENANCE 
Actions setup Exit 
- Function to Perform 
0 l save Database 
0 Save m Database 
0 Copy Error File 
0 &store Database 
Perform @ration - De&/Source - 0 0 Path & 
0 Path B: 
0 Path 
I SelPath 1 
Format Disk 
G. SAVJVRESTORE (SAVE) 
16.39 This 
program allows you to save and/or load the 
database, copy error logs to the disks, and to reset the 
system. 
16.40 To access the window shown above, select...

INTER-TELPRACTICES PROGRAMMING 
IMX/GMX 416/832 INST4LLATION & MAINTENANCE Issue 1, November 1994 
16.44 FUNCTION TO PERFORM: Select the 
option button associated with the desired operation. 
SAVE DATABASE: Information is sent from the 
system to the designated destination. Select the Per- 
form Operation command button. If you are using a 
floppy disk, a window appears that tells you to insert 
the disk in the appropriate drive. Insert the disk then 
select the OK command button to begin the transfer,...

PROGRAMMING 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
 
:; 
/ 
Actions &tup Exit 
I 
Serial Port 
::k 
: :~~‘~‘~.:.:s .,.,.,.,.,.,.,., 
: : : . . . A...: y:.... ‘........:i.:.:.~.‘.~.‘.‘.:.:.:.:.:.:.:.:.:.:.:.:.:.:.::::::::::::::::::::::~~:~:~~~:)~~~~,::::~~~~~~~~,~,~~~~~ .::::::: ~. 
zJ$, : ..... :.:: 
i 
I ‘:::: ye.:.:.:.::‘:::::‘.’ ::::::::::~::::::::::::::::::~:.~:.~.:,~ ~.~.~.~,~,~.,,,,,,,,,.,.,.,.,.,,,,,,,.,.,.,.,.,.,.,~.~.~.~.~.~~~~~~ ~.: 
. .  . . ....

INTER-TEL4PRACTICES PROGRAMMING 
IMWGMX 416/832 INSTALLATION & MAINTENANCE Issue 1, November 1994 
Actions &tup Exit 
Time: (1 Date: m ( [.) 
System Configuration 
n Non-blocking for voice channels 
Configuration 
I Digital Keyset Interface 
Keyset Interface 
Single-Line Interface 
DID Trunk Interface 
CO-Trunk Interface 
Loop Start Interface 
Upper +3OVDC Modules = 1 
Lower +30VDC Modules = 1 
Exit 
 
Mpve Board 
I. 
SYSTEM CONFIGUIWIION (CON-F) 
16.54 This 
window is used to set the system time, 
date,...

PROGRAMMING 
INTER-TEEPRACTICES 
Issue 1, November 1994 
IMX/GMX 416/832 INSTALLATION 8z MAINTENANCE 
16.58 MOVE BOARD: 
This option is available ody 
in stand-alone programming sessions. If you wish to 
move a board from its assigned location in the cardfile to 
an available slot, select the Move Board command but- 
ton. The following window appears. The list box shows 
all available slots. Move the highlight bar to the desired 
slot and then select the OK command button. Or, to 
leave the slot...

INTER-TELPRACTICES PROGRAMMING 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE Issue 1, November 1994 
16.61 CONFIGURATION: 
Keyset Interface, DID 
Trunk Interface, and Tl cards require additional pro- 
gramming to configure them. 
0 
KSC (IMX Only): MX dual-circuit version Keyset 
Interface cards (KSC-Ds) can have “single” circuits 
that support one keyset or “dual” circuits that can 
support two 8-line IMX AIM keysets. Highlight the 
desired Keyset Interface card in the System Con- 
figuration list box,...

PROGRAMMING 
Issue 1, November 1994 INTER-TELPRACTICES 
IMX/GMX 416/832 INSTALIATION dk MAINTENANCE 
I 
16.62 NON-BLOCKING FOR VOICE CHAN- 
NELS: Each 
voice bus (PCM highway) has 32 available 
time slots (voice channels) that are allocated for outside 
calls, intercom calls, and pages on a first-come, first- 
served basis. The software automatically distributes all 
equipped cards among the voice buses to make the best 
Possible use of the available times slots. If there is a 
large number of cards...

INTEaTELPRACTICES PROGRAMMING 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE Issue 1, November 1994 
FIGURE 5-4. INDIVIDUAL STATION PROGRAMMING (SIN) 
TO USE: Make a copy of this 3-page progr amming sheet for each station in the system. 
Circuit number 
Extension number 
Full name 
User name 
Station Exchange Password 
Miscellaneous Flags - 
Enabled or Disabled 
Page S-175  

PROGRAMMING 
INTER-TELPRACTICES 
Issue 1, November 1994 
IMX/GMX 416/832 INSTALLATION & MAINTENANCE 
FIGURE 5-4. INDIVIDUAL STATION PROGRAMMING (Continued) _ ‘ 
1 
Miscellaneous Station Information- 
Attendant 
Ah. Msg. Source 
Message Center 
Acct Code Type: SF/L/None 
Index 
Validate? 
yes 
orNo 
Class-of-service code: 
TenaxWDept. # 
Ring zone 
Outgoing 
Access - 
Day Trunk Groups: 
Night Trunk Groups: 
Programmable 
Keys - 
Key Map Number: 
Station Programmable Keys: 
1 
2 
3 
4 
5 
6 
7 
8...