InFocus Projector IN134UST User Manual

							IN134UST/IN136UST User’s Manual 
Using the Physical Lock 
Using the Kensington® Lock 
If you are concerned about security, attach the projector to a permanent object with the Kensington 
slot and a security cable.  
 
Note: 
Contact your vendor for details on purchasing a suitable Kensi ngton security cable.  
The security lock corresponds to Kensington’s Mi croSaver Security System. If you have any 
comments, contact: Kensington, 2853 Campus Drive, San Mateo,  CA 94403, U.S.A. Tel: 800-535-
4242, http://www.Kensington.com. 
 
Using the Security Bar 
In addition to the password protection function and  the Kensington lock, the Security Bar helps 
protect the projector fr om unauthorized removal. 
See the following picture. 
 
 
 
 
 
— 44 —
  
						

							IN134UST/IN136UST User’s Manual 
– 45  – 
TROUBLESHOOTING 
Common problems and solutions 
These guidelines provide tips to deal with problem s you may encounter while using the projector. If 
the problem remains unsolved, cont act your dealer for assistance. 
Often after time spent troubleshooting, the problem is traced to so mething as simple as a loose 
connection. Check the follow ing before proceeding to the  problem-specific solutions. 
  Use some other electrical device to confirm that the electrical outlet is working. 
   Ensure the projector is turned on. 
   Ensure all connections are securely attached.  
   Ensure the attached device is turned on. 
   Ensure a connected PC is not in standby mode. 
   Ensure a connected notebook computer is configured for an external display. 
(This is usually done by pressing a Fn-key combination on the notebook). 
Tips for Troubleshooting 
In each problem-specific section, tr y the steps in the order suggested. This may help you to solve the 
problem more quickly. 
Try to pin point the problem and thus  avoid replacing non-defective parts.  
For example, if you replace batteries and the problem remains, put the original batteries back and go 
to the next step.  
Keep a record of the steps you take when troubl eshooting: The information may be useful when 
calling for technical support or for passing on to service personnel. 
  
						

							IN134UST/IN136UST User’s Manual 
— 46 — 
LED Error Messages 
ERROR CODE MESSAGES POWER LED 
GREEN 
LAMP LED 
AMBER 
TEMP LED 
RED 
Power On  ON OFF  OFF 
Power Off  ON OFF  OFF 
Cooling Flashing  OFF OFF 
Over Temperature  OFF OFF  ON 
Thermal Break Sensor error  4 blinks OFF OFF 
Lamp error  OFF ON OFF 
Fan 1  6 blinks 1 blink  OFF 
Fan 2  6 blinks 2 blinks  OFF 
Fan 3  6 blinks 3 blinks  OFF 
Fan 4  6 blinks 4 blinks  OFF 
Lamp Door Open  7 blinks  OFF OFF 
DMD error  8 blinks OFF OFF 
Color wheel error  9 blinks OFF OFF 
In the event of an error, pleas e disconnect the AC power cord and wait for one (1) minute before 
restarting the projector. If the POWER or LAMP LE Ds continue to blink or the TEMP LED is lit, 
contact your service center. 
Image Problems 
Problem: No image appears on the screen 
1.  Verify the settings on your notebook or desktop PC. 
2.  Turn off all equipment and power up again in the correct order. 
Problem: The image is blurred  
1. Press the  Auto button on the remote control or projector. 
2.  Ensure the projector-to-screen distance  is within the specified range. 
3.  Check that the projector lens is clean. 
Problem: The image is wider at the top or bottom (trapezoid effect)  
1. Position the projector so it is as perpendicular to the screen as possible.  
2.  Use the  Keystone button on the remote control or projector to correct the problem. 
Problem: The image is reversed  
Check the  Projection setting on the  Installation I menu of the OSD. 
Problem: The image is streaked  
1. Set the  Frequency  and Tracking settings on the  Computer menu of the OSD to the 
default settings. 
2.  To ensure the problem is not caused by a connected PC’s video card, connect to another 
computer.  
Problem: The image is flat with no contrast  
Adjust the  Contrast setting on the Image  menu of the OSD.  
						

							IN134UST/IN136UST User’s Manual 
– 47  – 
Problem: The color of the projected image does not match the source imag\
e. 
Adjust the  Color Temperature  and Gamma settings on the  Image menu of the OSD. 
Lamp Problems 
Problem: There is no light from the projector  
1. Check that the power cable is securely connected. 
2.  Ensure the power source is good by te sting with another electrical device. 
3.  Restart the projector in the correct orde r and check that the Power LED is on. 
4.  If you have replaced the lamp recently,  try resetting the lamp connections.  
5.  Replace the lamp module. 
6.  Put the old lamp back in the projector and have the projector serviced. 
Problem: The lamp goes off 
1. Power surges can cause the lamp to turn  off. Re-plug power cord. When the POWER LED 
is on, press the power button. 
2.  Replace the lamp module. 
3.  Put the old lamp back in the projector and have the projector serviced. 
Remote Control Problems 
Problem: The projector does not respond to the remote control  
1. Direct the remote control towards remote sensor on the projector.  
2.  Ensure the path between remote and sensor is not obstructed. 
3.  Turn off any fluorescent lights in the room. 
4.  Check the battery polarity. 
5.  Replace the batteries. 
6.  Turn off other Infrared-enabled devices in the vicinity. 
7.  Have the remote control serviced. 
Having the Projector Serviced 
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in 
the original carton. Include a description of the problem and a checklist of  the steps you took when 
trying to fix the problem: The information may be us eful to service personnel. To arrange for service, 
contact InFocus Technical Support at  http://www.infocus.com/support
. 
  
						

							IN134UST/IN136UST User’s Manual 
— 48 — 
HDMI Q & A 
Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI 
cable? 
1.  Recently, HDMI Licensing, LLC announced  that cables would be tested as Standard or 
High-Speed cables.  
2.  ˙Standard (or “category 1”) HDMI cables have  been tested to perform at speeds of 75Mhz 
or up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.  
3.  ˙High Speed (or “category 2”) HDMI cables hav e been tested to perform at speeds of 
340Mhz or up to 10.2Gbps, which is the highe st bandwidth currently available over an 
HDMI cable and can successfully handle 1080p  signals including those at increased color 
depths and/or increased refresh rates from the Source. High-Speed cables are also able to 
accommodate higher resolution displays, such as WQXGA cinema monitors (resolution of 
2560 x 1600). 
 
Q. How do I run HDMI cables longer than 10 meters? 
4.  There are many HDMI Adopters working on HDMI solutions that extend a cable’s 
effective distance from the typical 10 meter rang e to much longer lengths. These companies 
manufacture a variety of solutions that include active cables (active electronics built into 
cables that boost and extend the cable’s signal),  repeaters, amplifiers as well as CAT5/6 and 
fiber solutions. 
 
Q. How can I tell if a cable is an HDMI certified cable? 
5.  All HDMI products are requir ed to be certified by the manufacturer as part of the HDMI 
Compliance Test Specification. However, ther e may be instances where cables bearing the 
HDMI logo are available but have not been proper ly tested. HDMI Licensing, LLC actively 
investigates these instances  to ensure that the HDMI trademark is properly used in the 
market. We recommend that consumers buy their cables from a reputable source and a 
company that is trusted. 
 
For more detail information check  http://www.hdmi.org/lear
ningcenter/faq.aspx#49 
  
						

							IN134UST/IN136UST User’s Manual 
– 49  – 
SPECIFICATIONS 
Specifications 
Model  IN134UST IN136UST 
Display type DMD 0.55 XGA DMD 0.65 WXGA 
Native Resolution XGA 1024 x 768 Native WXGA 1280 x 800 Native 
Projection distance  371~417mm
  336~421mm 
Projection screen size 
(diagonal)  4:3 (68~85”) 16:10 (80”~100”) 
Projection lens 
Manual Focus 
Throw ratio 0.437 0.35 
Vertical keystone correction  +/- 40 degrees 
Projection methods Front, Rear, Desktop/Ceiling (Rear, Front) 
Data compatibility  VGA, SVGA, XGA, SXGA, UXGA, Mac 
SDTV/EDTV/ HDTV 480i, 576i, 480p, 576p, 720p, 1080i, 1080p 
Video compatibility NTSC/NTSC 4.43, PAL (B
/G/H/I/M/N/60), SECAM 
H-Sync  15, 31 – 91.4 kHz 
V-Sync 24-30 Hz, 47-120 Hz 
Safety certification FCC, UL/cUL, CE, CCC, KC, UL-S
, TUV/GS, ECA-PCT, SASO, SABS, 
PSB, CECP, NOM, C-Tick 
Operation temperature  5° ~ 40°C 
Dimensions (W x D x H) 287.7 mm x 374.5 mm x 160 mm  
AC Input  AC Universal 100 ~ 240V 
Power consumption 260W(Eco), 
						

							IN134UST/IN136UST User’s Manual 
Projection Distance vs. Projection Size 
 
Projection Distance and Size Table 
IN136UST 
WXGA  
16:10 
Diagonal 80 87 97 100 
Distance  282.3+/-20mm 336.3+/-20mm  421.4+/-20mm 445.8+/-20mm 
Image Width  1723mm 1869mm  2088mm 2154mm 
Image Height  1077mm 1168mm  1305mm 1346mm 
H  280+/-50mm 298.5+/-50mm  325.5+/-50mm 336.9+/-50mm 
 
IN134UST 
XGA  
4:3 
Diagonal  68 78  82 85 
Distance 282.3+/-20mm 371.4+/-20mm 417.35+/-20mm 445.8+/-20mm 
Image Width  1382mm 1566mm  1670mm 1727mm 
Image Height  1036mm 1175mm  1240mm 1295mm 
H  301.3+/-50mm 334.8+/-50mm  350.8+/-50mm 363.7+/-50mm 
— 50 —  
						

							IN134UST/IN136UST User’s Manual 
– 51  – 
Timing Mode Table 
The projector can display several resolutions. The  following table outlines the resolutions that can be 
displayed by the projector. 
SIGNAL RESOLUTION H-SYNC  
(KHZ) 
V-SYNC
(HZ) 
COMPOSITE
S_VIDEO COMPONENT RGB 
(ANALOG) 
DVI/ 
HDMI 
(DIGITAL)
NTSC  － 
15.734 60.0  ○  － 
－ － 
PAL/SECAM  － 
15.625 50.0  ○  － 
－ － 
720 X 400 31.5 70.1 － － ○ ○ 
640 X 480 31.5  60.0 － 
－ ○ ○ 
640 X 480 37.9  72.8 － 
－ ○ ○ 
640 X 480 37.5  75.0 － 
－ ○ ○ 
800 X 600 35.2  56.3 － 
－ ○ ○ 
* 800 X 600 37.9  60.3 － 
－ ○ ○ 
800 X 600 46.9  75.0 － 
－ ○ ○ 
800 X 600 48.1  72.2 － 
－ ○ ○ 
800 X 600 53.7  85.1 － 
－ ○ ○ 
** 800 X 600 76.3  120.0 － 
－ ○ ○ 
* 1024 X 768 48.4  60.0 － 
－ ○ ○ 
1024 X 768 56.5  70.1 － 
－ ○ ○ 
1024 X 768 60.0  75.0 － 
－ ○ ○ 
1024 X 768 68.7  85.0 － 
－ ○ ○ 
** 1024 X 76897.6 120.0  － 
－ ○ ○ 
1024 X 768 99.0  120.0 － 
－ ○ ○ 
1152 X 864 67.5  75.0 － 
－ ○ ○ 
* 1280 X 720 45.0  60.0 － 
－ ○ ○ 
** 1280 X 72090.0 120.0  － 
－ ○ ○ 
1280 X 768 47.4  60.0 － 
－ ○ ○ 
* 1280 X 768 47.8  59.9 － 
－ ○ ○ 
* 1280 X 800 49.7  59.8 － 
－ ○ ○ 
1280 X 800 62.8  74.9 － 
－ ○ ○ 
1280 X 800 71.6  84.9 － 
－ ○ ○ 
VESA 
**
 1280 X 800 101.6 119.9  － 
－ ○ ○  
						

							IN134UST/IN136UST User’s Manual 
— 52 — 
SIGNAL RESOLUTION H-SYNC  
(KHZ) 
V-SYNC
(HZ) 
COMPOSITE
S_VIDEO COMPONENT RGB 
(ANALOG) 
DVI/ 
HDMI 
(DIGITAL)
*** 1280 X 1024 64.0  60.0 － 
－ ○ ○ 
1280 X 1024 80.0  75.0 － 
－ ○ ○ 
1280 X 1024 91.1 85.0 － － ○ ○ 
*** 1280 X 960 60.0  60.0 － 
－ ○ ○ 
1280 X 960 85.9  85.0 － 
－ ○ ○ 
*** 1360 X 768 47.7  60.0 － 
－ ○ ○ 
*** 1400 X 1050 65.3  60.0 － 
－ ○ ○ 
1440 X 900 55.5  59.9 － 
－ ○ ○ 
*** 1440 X 900 55.9  59.9 － 
－ ○ ○ 
1440 X 900 70.6  75.0 － 
－ ○ ○ 
1600 X1200 75.0 60 － － ○ ○ 
1680 X 1050 64.7 59.9 － － ○ ○ 
1680 X 1050 65.3 60.0 － － ○ ○ 
1920 X 1200RB 74.0 60.0 － － ○ ○ 
1920 X 1080 67.5 60.0 － － ○ ○ 
640 X 480 35.0  66.7 － 
－ ○ ○ 
832 X 624 49.7  74.5 － 
－ ○ ○ 
1024 X 768 60.2  74.9 － 
－ ○ ○ 
Apple 
Macintosh 
1152 X 870 68.7 75.1 － － ○ ○ 
480I 15.734 60.0 － ○  － ○ 
SDTV 
576I 15.625 50.0 － ○ － ○ 
576P 31.3 50.0 － ○ － ○ 
EDTV 
480P 31.5 60.0 － ○ － ○ 
720P 37.5 50.0 － ○ － ○ 
720P 45.0 60.0 － ○ － ○ 
1080I 33.8 60.0 － ○ － ○ 
1080I 28.1 50.0 － ○ － ○ 
1080P 27.0 24.0 － ○ － ○ 
1080P 28.0 25.0 － ○ － ○ 
HDTV 
1080P 33.7 30.0 － ○ － ○  
						

							IN134UST/IN136UST User’s Manual 
– 53  – 
SIGNAL RESOLUTION H-SYNC  
(KHZ) 
V-SYNC
(HZ) 
COMPOSITE
S_VIDEO COMPONENT RGB 
(ANALOG) 
DVI/ 
HDMI 
(DIGITAL)
1080P 56.3 50.0 － ○  － ○ 
1080P 67.5 60.0 － ○ － ○ 
 
O: Frequency supported 
—: Frequency not supported 
 3D note ： 
“  ” means the timing can support non-3D and  3D signals with Frame Sequential and Top-
Bottom format. 
“ ” means the timing can support non-3D and 3D  signals with Frame Sequential format. 
“ ” means the timing can support non-3D and 3D signals with Top-Bottom format. 
Depending on the EDID files and display cards of t he 3D source, it is possible the user will not be 
able to choose any of the above 3D timings. 
 The projectors native resolution is 1280 x 800. If  the resolution of the source is different than  
1280 x 800, the projector may di splay uneven sized text and lines. 

 Signal types highlighted yellow can  only be displayed in 4:3 mode. 
 Signal types highlighted in blue may display small amounts of noise. Th is is because the Video 
Sync mode cannot adjust these signals automatically. 

 The DVD player monitors HDTV time. VG828 is secondary to the DVD player. 
  RB=Reduced Blacking