InFocus Projector IN134UST User Manual

							IN134UST/IN136UST User’s Manual 
Rear view 
1516
123
456
789
10
14 13
12 11
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  Security bar  For security purposes 
2.  Kensington lock Secure to a permanent object with a Kensington® 
Lock system 44 
3.  3D SYNC Connect the 3D IR glasses transmitter 
(Note: For Vivitek brand 3D IR glasses only) 
4.  AUDIO IN Connect an AUDIO cable from the 
audio device. (Supports audio for 
VGA IN-1, VGA IN-2, Composite, and S-video sources.) 
5.  AUDIO OUT  Connect an AUDIO cable to an audio amplifier 
6.  MIC Connect a microphone 
7.  RS-232 Connect a RS-232 serial port cable for remote control 
8.  USB  Connect a USB cable from a computer 
9.  AC IN Connect a POWER cable 11 
10.  VGA IN – 2  Connect a RGB cable from a computer or component device 
11.  VGA IN – 1 Connect a RGB cable from a computer or component device 
12.  VGA OUT Connect a RGB cable to a display 
(Loop through only available using VGA IN-1) 
13.  S-VIDEO 
Connect a S-video cable from a video device 
— 4 —  
						

							IN134UST/IN136UST User’s Manual 
– 5  – 
ITEM  LABEL  DESCRIPTION SEE PAGE 
14.  VIDEO   Connect a composite cable from a video device 
15.  HDMI Connect an HDMI cable from a HDMI device 
16.  RJ45 Connect a LAN cable from Ethernet 
Note: 
If your video equipment has various input sources,  it is recommended that you connect the cables 
in the following order for the best picture quality  : HDMI/DVI, component (thru VGA), Composite. 
 
Warning: 
As a safety precaution, disconnect all power to the projector and connecting devices before making 
connections.  
						

							IN134UST/IN136UST User’s Manual 
Bottom view 
— 6 — 
247.
01
135.51
12221
1
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  Tilt adjustor  Rotate adjuster lever to adjust angle position 14 
2.  Ceiling support holes Contact your dealer for information on mounting the projector on a 
ceiling 
 
Note: 
When installing, ensure that you us
e only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting har dware and M4 screws with a maximum screw 
depth of 12 mm (0.47 inch).  
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount 
load capacity must exceed the  weight of the installed equipment, and as an additional precaution 
be capable of withstanding three times the weight  of the equipment (not less than 5.15 kg) over a 
period of 60 seconds. 
  
						

							IN134UST/IN136UST User’s Manual 
Remote Control Parts 
123
4
5
6
7
89
10
11
12
13
14 15
 
Important: 
1.
 Avoid using the projector with bright fluore scent lighting turned on. Certain high-frequency 
fluorescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the  remote control and the projector. If the path 
between the remote control and the  projector is obstructed, you can bounce the signal off certain 
reflective surfaces such  as projector screens. 
 
3. The buttons and keys on the projector have the  same functions as the corresponding buttons on 
the remote control. This user’s manual descri bes the functions based on the remote control. 
– 7  –  
						

							IN134UST/IN136UST User’s Manual 
— 8 — 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Up cursor   Navigates and changes settings in the OSD 
2.  Enter  Changes settings in the OSD 
16 
3.  Power  Turns the projector on or off 11 
4.  Right cursor   Navigates and changes settings in the OSD  
5.  Volume +  Increases volume 
6.  Volume -  Decreases volume 
15 
7.  Mute Mutes the built-in speaker 
8.  Freeze  Freeze/unfreezes the on-screen picture 
9.  Source  Selects the input device 
10.  Auto Auto adjustment for frequency, tr acking, size, position (RGB only) 
11.  Keystone top Corrects keystoning of the image (when it is wider on 
top) 
12.  Keystone bottom Corrects keystoning of the image (when it is wider on 
the bottom) 
15 
13.  Down cursor 
Navigates and changes settings in the OSD 
14.  Left cursor  Navigates and changes settings in the OSD  
15.  Menu Opens and exits the OSD  
16  
						

							IN134UST/IN136UST User’s Manual 
– 9  – 
Remote Control Operating Range 
The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a little closer.  
Projector and Remote Control Buttons 
The projector can be operated using the remote c ontrol. All operations can be carried out with the 
remote control. 
  
						

							IN134UST/IN136UST User’s Manual 
— 10 — 
SETUP AND OPERATION 
Inserting the Remote  Control Batteries  
1.  Remove the battery compartment 
cover by sliding the cover in the 
direction of the arrow (A). Pull out the 
cover  (B). 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution:  
1. Only use a 3V lithium battery (CR2025). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for prolonged periods. 
 
Note: 
Batteries are not normally included with InFocus projectors. 
  
						

							IN134UST/IN136UST User’s Manual 
Starting and Shutting down the Projector 
1.  Connect the power cord to the 
projector. Connect the other end to 
a wall outlet. 
2.  Turn on the connected devices. 
 
3.  Ensure the POWER LED displays a 
solid green. Then press the POWER  
button 
of the remote to turn on the 
projector.  
 
The projector splash screen displays 
and connected devices are 
detected. 
 
See Setting an Access Password 
(Security Lock)  on page 12 if 
security lock is enabled.

 
4.  If more than one input device is 
connected, press the  SOURCE 
button 
of the remote and use  ▲▼ to 
scroll among the devices. 
(Component is supported using a 
RGB to COMPONENT ADAPTER.) 
 
 
   VGA 1/VGA 2: Analog RGB 
Component: DVD input YCbCr / YPbPr, or 
HDTV input YPbPr via HD15 connector 
   Composite Video: Traditional composite video 
 HDMI: HDMI, DVI 
  
S-Video: Super video (Y/C separated) 
5.  When the “Power Off? Press Power 
again” message appears, press the 
POWER  button. The projector turns 
off. 
 
Caution: 
Do not unplug the power cord until the POWE R LED changes to solid green–indicating the 
projector has cooled down. 
– 11  –  
						

							IN134UST/IN136UST User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered after you power on the projector. (See  Navigating the 
OSD  on page  16 and Setting the OSD Langua
 ge on page  17 for help on using OSD menus.) 
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password, contact InFocus S upport for information on clearing the password.  
1.  Press the MENU button to open the 
OSD menu. 
2.  Press the  ◄► buttons to move to the 
Installation I  menu. 
3.  Press the ▲▼ buttons to select  
Advanced . 
— 12 —  
						

							IN134UST/IN136UST User’s Manual 
 
4.  Press the ▲▼ buttons to select  
Security Lock . 
5.  Press the ◄► buttons to enable or 
disable security lock function. 
A password dialog box automatically  
appears. 
6.  You can use the cursor buttons 
▲▼◄►  
on IR remote control for password 
entry. You can use any combination 
including the same arrow five times, 
but five characters must be used. 
Press the cursor buttons in any order 
to set the password. Push the  MENU 
button  to exit the  dialog box. 
7.  If the Security Lock is enabled, the 
user will be prompted to enter a 
password when the projectors power 
button is pressed. 
Enter the password in the order you 
set it at step 5. In case you forget the 
password, please contact the service 
center.  
Service center will validate the owner 
and help reset the password.  
 
–  13  –