InFocus Projector IN134UST User Manual

							IN134UST/IN136UST User’s Manual 
Video Menu  
Press the MENU button to open the  OSD menu. Press the  ◄► buttons to move to the  Video menu. 
Press the ▲▼  buttons to move up and down in the  Video menu. Press ◄► to change setting values. 
Note: 
Available settings vary depending on the  input source. Others will appear grayed out. 
 
ITEM DESCRIPTION 
Video AGC Press the 
◄► buttons to enable or disable the Automatic Gain Control for video 
source. 
Video Saturation  Press the ◄► buttons to adjust the video saturation. 
Video Tint  Press the ◄► buttons to adjust the video tint/hue. 
Film Mode  Press the ◄► buttons to select a different film mode.  
Video Overscan  Press the ◄► buttons to enable or disable video over scan. 
Closed Captioning  Press the ◄► buttons to enable or disable closed captioning. 
Reset Press  (Enter) / ►  to reset all settings to default values. 
Audio Press  (Enter) / ► to o enter the Audio menu. See  Audio on page  25. 
 
Note: 
Video jagging may occur when playing interlace  video. To overcome this issue, open the  
Video menu and adjust the Film Mode feature.  
— 24 —  
						

							IN134UST/IN136UST User’s Manual 
Audio 
Press  (Enter) / ► to enter the  Audio sub menu. 
 
ITEM DESCRIPTION 
Volume Press  the ◄►  buttons to adjust the audio volume.  
Mute Press  the ◄►  buttons to turn on or off the speaker. 
Audio Input  Press the ◄► buttons to select audio input. 
 
– 25  –  
						

							IN134UST/IN136UST User’s Manual 
Installation I Menu  
Press the MENU button to open the  OSD menu. Press the  ◄► buttons to move to the  Installation I 
menu. Press the  ▲▼ buttons to move up and down in the  Installation I menu. Press ◄► to change 
setting values. 
 
ITEM DESCRIPTION 
Language Press  the ◄►  buttons to change the OSD language. 
Blank Screen  Press the ◄► buttons to select a different blank screen color. 
Projection  Press the 
◄► buttons to choose between different projection methods 
(Ceiling, Rear, etc.). 
Aspect Ratio  Press the 
◄► buttons to adjust the video aspect ratio. 
Note: This feature is unavailable when WhiteBoard is being used. 
Keystone Press  the ◄►  buttons to adjust the display keystone. 
Advanced  Press  (Enter) / 
► to access the Advanced menu. See  Advanced Features on 
page  27. 
Reset Press  (Enter) / ►  to reset all settings to default values (except Language). 
 
— 26 —  
						

							IN134UST/IN136UST User’s Manual 
Advanced Features 
Press the Menu button to open the OSD menu. Press  ◄► to move to the  Installation I menu. Press 
▲▼  to move to the  Advanced menu and then press  Enter or ►. Press  ▲▼ to move up and down in 
the  Advanced  menu. Press  ◄► to change setting values. 
 
ITEM DESCRIPTION 
Security Lock  Press the ◄► buttons to enable or disable the security lock function. 
Wall Color  Press the 
◄► buttons to enable or disable the wall color function. 
(Off/ Light Yellow/ Pink/ Light Green/ Blue/ Blackboard) 
Presentation Timer  Press  (Enter) / 
► to go to the Presentation Timer Menu. See  Presentation Timer 
belo
w. 
Digital Zoom   Press the ◄► buttons to adjust the Digital Zoom menu. 
Keypad Lock  Press the ◄► buttons to enter and enable or disable keys can be work on keypad. 
Logo Press  the ◄►  buttons to enter and select logo. 
Logo Capture  Press  (Enter) / ► to capture screen pattern to Logo. 
 
– 27  –  
						

							IN134UST/IN136UST User’s Manual 
Presentation Timer 
The Presentation Timer function can indicate the presentation ti me on the screen to help you achieve 
better time management while giving a presentation. 
 
ITEM DESCRIPTION 
Timer Press  the ◄►  buttons to enable or disabl e the presentation timer. 
Timer Period Press the ◄► buttons to select the timer period (1 ~ 60 minutes) 
Timer Reset  Press  (Enter) / ► to reset the timer settings. 
— 28 —  
						

							IN134UST/IN136UST User’s Manual 
Installation II Menu  
Press the MENU button to open the  OSD menu. Press the  ◄► buttons to move to the  Installation II 
menu. Press the  ▲▼ buttons to move up and down in the Installation II menu.  
 
ITEM DESCRIPTION 
Auto Source  Press the ◄► buttons to enable or disable automatic source detection. 
Auto Power Off 
(min.)  Press the 
◄► buttons to enable or disable automatic shutdown of lamp when there is 
no signal.  
Auto Power On  Press the 
◄► buttons to enable or disable automatic power On when AC power is 
supplied. 
Fan Speed  Press the 
◄► buttons to toggle between Normal and High fan speeds.  
Note:  It is recommended that the Fan Speed be set to high speed when the altitude of 
the environment is higher than 1500m (4021 ft). 
Lamp Mode  Press the 
◄► buttons to select the lamp mode for higher brightness or lower 
brightness to save lamp life. 
Advanced  Press  (Enter) / 
► to enter the Advanced menu. See  Advanced Feature on page 
30 . 
Factory Reset  Press  (Enter) / ►
 to reset all items to factory preset values. 
Status  Press  (Enter) / 
►
 to enter the Status menu. See page 
38 for more information on 
Status . 
 
– 29  –  
						

							IN134UST/IN136UST User’s Manual 
Advanced Features 
Press the Menu button to open the OSD menu. Press  ◄► to move to the  Installation II menu. 
Press  ▲▼ to move to the  Advanced menu and then press  Enter or ►. Press  ▲▼ to move up and 
down in the  Advanced menu. Press  ◄► to change setting values. 
 
ITEM DESCRIPTION 
OSD Menu Setting  Press  (Enter) / 
► to enter the OSD setting menu. See page  31 for more 
information on OSD Menu Setting . 
Peripheral Test Press  (Enter) / 
► to enter the Peripheral Test menu. See page  31 for more 
information on Peripheral Test . 
Lamp Hour Reset After replacing the lamp, this item should be reset. See page 
41 for more information 
on  Resetting the Lamp . 
Low Power Mode  Press ◄► to turn Low Power Mode on or off. 
3D  Press  (Enter) / 
► to enter the 3D menu. See page  33 for more information on  3D 
set
tings. 
Network  Press  (Enter) / 
► to enter the Network menu. See page  34 for more information on 
Network  settings. 
 
Note: 
To enjoy the 3D function, fi rst enable the Play Movie in 3D setting found in your DVD  
device under the 3D Disc Menu. 
 
— 30 —  
						

							IN134UST/IN136UST User’s Manual 
OSD Menu Setting  
 
ITEM DESCRIPTION 
Menu Position Press the ◄► buttons to select a different OSD location. 
Translucent Menu  Press the ◄► buttons to select the OSD background translucent level.  
Menu Display  Press the ◄► buttons to select the OSD timeout delay. 
Peripheral Test 
 
ITEM DESCRIPTION 
Remote Control 
Test  Press  (Enter) / 
► to test the IR remote controller for diagnostic purposes. 
Color Test  Press  (Enter) / 
► to select different color test patterns. Used for calibration and 
testing purposes. 
USB Test  Press  (Enter) / ► to test the USB connection with the connected PC. 
– 31  –  
						

							IN134UST/IN136UST User’s Manual 
Lamp Hour Reset 
 
Please refer to Resetting the Lamp  on page 41 to reset the lamp hour counter. 
— 32 —  
						

							IN134UST/IN136UST User’s Manual 
3D 
 
ITEM DESCRIPTION 
3D Press the ◄►  buttons to select Off, DLP-Link or IR. 
3D Sync Invert  Press the ◄► buttons to turn 3D Sync Invert On or Off. 
3D Format  Press the ◄► buttons to enable or disable 3D Format. 
Note: 
1.  By default, if no 3D source is detected,  the 3D OSD menu items will not be available. 
2. When the projector is connected to an appropriate  3D source, the 3D OSD menu items are available 
for selection. 
3.  Use 3D glasses to view a 3D image. 
4. You need 3D content from a 3D DVD or 3D media file. 
5.  You need to enable the 3D source (some 3D DVD  content may have a 3D on-off selection feature). 
6.  You need DLP link 3D or IR 3D shutter glasses. With IR 3D shutter glasses, you need to install a 
driver on your PC and connect a USB emitter. 
7.  The 3D mode of the OSD needs to match the type of glasses (DLP link or IR 3D). 
8.  Power on the glasses. Glasses normally have a power on -off switch.  
Each type of glasses has their own configuration instructions.  Please follow the configuration 
instructions that come with your glasses to finish the setup process. 
 
 
–  33  –