IBM Thinkpad X30 X31 Manual

							1060 Keyboard
For access, remove following FRU:
v“1010 Battery pack”on page 71
1
1
Step Screw (quantity) Torque

1M2×6 mm, nylon-coated (4) 0.245 Nm
(2.5 kgfcm)
(continued)
Removing and replacing a FRU
ThinkPad X30, X3177 
						

							In step
4, open the keyboard slightly in the direction of
the arrow.
3
4
2
In step
5, draw the keyboard a little in the direction of
the arrow, and then detach the connector
6.
6
5
Removing and replacing a FRU
78ThinkPad X30, X31 (MT 2672/2673) 
						

							When installing:Install the keyboard, do as follows;
1. Attach the connector.
2. Make sure that the keyboard edges, shown in the
figure as(A)and(B), are under the frame.
(B)(A)
(continued)
Removing and replacing a FRU
ThinkPad X30, X3179 
						

							3. Press the keys indicated by arrows to latch the
keyboard firmly in place.
4. To make sure that the front side of the keyboard is
housed firmly, gently press the keys with your thumbs
and try to slide the keyboard toward you.
5. Secure the keyboard by tightening the screws from the
bottom side of the computer.
Removing and replacing a FRU
80ThinkPad X30, X31 (MT 2672/2673) 
						

							1070 Mini PCI adapter
For access, remove following FRUs, in order:
v“1010 Battery pack”on page 71
v“1060 Keyboard”on page 77
802.11b wireless LAN/modem combo card
1
(continued)
Removing and replacing a FRU
ThinkPad X30, X3181 
						

							32
2
Antenna cables
4aand
4bin the following illustration
are for the wireless LAN feature, and
5is for the modem
feature.
Note:When unplugging the antenna jack, do not pull the
cable; it might snap. Unplug the jack by pulling a
tab with your fingers.
5
4a
4b
Removing and replacing a FRU
82ThinkPad X30, X31 (MT 2672/2673) 
						

							When installing:
vMake sure that the connector
5is firmly attached.
vPlug the gray antenna cable with the tab marked“MAIN”
(
4a) into jackJ1,orMAIN,orM, and the black
antenna cable with the tab marked“AUX”(
4b) into
jackJ2,orAUX,orA.
vWith the notched end of the card toward the socket,
insert the card into the socket, and then press it firmly.
Pivot the card until it snaps into place. Make sure that
the card is firmly fixed in the slot and does not move
easily.
Cable routing for the 802.11b/modem combo card
When attaching the Mini PCI adapter, route the antenna
cables to go under the cable guide as in
a, and place
the tabs as indicated by arrow
bin this figure.
a
b
Removing and replacing a FRU
ThinkPad X30, X3183 
						

							802.11b wireless LAN card
1
(continued)
Removing and replacing a FRU
84ThinkPad X30, X31 (MT 2672/2673) 
						

							32
2
Antenna cables
4aand
4bin the following illustration
are for the wireless LAN feature.
Note:When unplugging the antenna jack, do not pull the
cable; it might snap. Unplug the jack by pulling a
tab with your fingers.
4b
4a
When installing:
vPlug the gray antenna cable with the tab marked“MAIN”
(
4a) into jackJ1,orMAIN,orM, and the black
antenna cable with the tab marked“AUX”(
4b) into
jackJ2,orAUX,orA.
vWith the notched end of the card toward the socket,
insert the card into the socket, and then press it firmly.
Pivot the card until it snaps into place. Make sure that
the card is firmly fixed in the slot and does not move
easily.
Removing and replacing a FRU
ThinkPad X30, X3185 
						

							802.11a/b wireless LAN card
NoteThis procedure is not applicable for the following
model. For the model, the removal procedure is
same as in“802.11b wireless LAN card”on page 84
though the model supports 802.11a/b wireless LAN
card.
v2672-JHJ
2
1
Step Screw (quantity) Torque

1M2×3 mm, T7, nylon-coated (1) 0.245 Nm
(2.5 kgfcm)
(continued)
Removing and replacing a FRU
86ThinkPad X30, X31 (MT 2672/2673)