IBM Thinkpad R40 R40e Manual

							2000 Ultrabay Plus guide rail
For access, remove these FRUs, in order:
vª1010 Battery packº on page 64
vª1050 Mini PCI adapterº on page 70
vª1060 Keyboardº on page 73
vª1100 Hinge coverº on page 87
vª1150 LCD assemblyº on page 98
vª1160 Keyboard bezelº on page 103
1
Step Screw (quantity) Torque
«1¬M2.0 ý 3.5 mm, Silver (2) 0.294 Nm
(3 kgfcm)
(continued)
Removing and replacing a FRU
ThinkPad R4011 7 
						

							a
1
2
Step Screw (quantity) Torque
«1¬M2 ý 13 mm, Silver (1) 0.294 Nm
(3 kgfcm)
«2¬M2.0 ý 3.5 mm, Silver (1) 0.294 Nm
(3 kgfcm)
When installing:Attach the Ultrabay Plus guide rail so
that the two small projections on the
ultrabay device connector fit into the
holes«a¬provided, and then secure the
screws.
Removing and replacing a FRU
11 8ThinkPad R40 
						

							2010 I/O Bracket
For access, remove these FRUs, in order:
vª1010 Battery packº on page 64
vª1020 Ultrabay Plus deviceº on page 65
vª1030 Hard-disk driveº on page 66
vª1040 DIMMº on page 68
vª1050 Mini PCI adapterº on page 70
vª1060 Keyboardº on page 73
vª1100 Hinge coverº on page 87
vª1150 LCD assemblyº on page 98
vª1160 Keyboard bezelº on page 103
vª1180 System boardº on page 109
vª2000 Ultrabay Plus guide railº on page 117
1
2
Step Screw (quantity) Torque
«1¬Hex stud (4) 0.294 Nm
(3 kgfcm)
Removing and replacing a FRU
ThinkPad R4011 9 
						

							2020 LCD front bezel
For access, remove these FRUs, in order:
vª1010 Battery packº on page 64
vª1050 Mini PCI adapterº on page 70
vª1060 Keyboardº on page 73
vª1100 Hinge coverº on page 87
vª1150 LCD assemblyº on page 98
After removing screws«1¬and detach all of the latches
«2¬to«6¬in order.
1
6
4
3
2
5
Step Screw (quantity) Torque
«1¬M2.5 ý 6 mm, Yellow (2) 0.294 Nm
(3 kgfcm)
When installing:Make sure that all of the latches of the
LCD front bezel are firmly attached to
the LCD cover.
Removing and replacing a FRU
120ThinkPad R40 
						

							2030 Inverter card
For access, remove these FRUs, in order:
vª1010 Battery packº on page 64
vª1050 Mini PCI adapterº on page 70
vª1060 Keyboardº on page 73
vª1100 Hinge coverº on page 87
vª1150 LCD assemblyº on page 98
vª2020 LCD front bezelº on page 120
3
1
2
Step Screw (quantity) Torque
«1¬M2.5 ý 5 mm, Black (2) 0.294 Nm
(3 kgfcm)
When installing:Make sure that connectors«2¬and«3¬
are firmly attached.
Cable routing:When replacing the inverter card, route
the connector cable as in the following
figure:
Removing and replacing a FRU
ThinkPad R40121 
						

							2040 LCD panel and LCD cable
assembly
For access, remove these FRUs, in order:
vª1010 Battery packº on page 64
vª1050 Mini PCI adapterº on page 70
vª1060 Keyboardº on page 73
vª1100 Hinge coverº on page 87
vª1150 LCD assemblyº on page 98
vª2020 LCD front bezelº on page 120
vª2030 Inverter cardº on page 121
2
2
1
11a
Step Screw (quantity) Torque
«1¬M2.5 ý 5 mm, Black (2) 13 and 14
inch0.343 Nm
(3.5 kgfcm)
«1¬+«1a¬M2.5 ý 5 mm, Black (3) 15 inch 0.343 Nm
(3.5 kgfcm)
«2¬M2.0 ý 4.0 mm, Black (4) 0.196 Nm
(2 kgfcm)
(continued)
Removing and replacing a FRU
122ThinkPad R40 
						

							2
4
3
When installing the LCD panel, do the following:
vPlace the FPC connector under the black antenna
cable.
vMake sure that the antenna cables are firmly routed to
fit to the cable guides of the LCD cover.
vMake sure that the antenna cables are not pinched
under the LCD panel.
Removing and replacing a FRU
ThinkPad R40123 
						

							2050 Antenna assembly, hinges, and
LCD cover
For access, remove these FRUs, in order:
vª1010 Battery packº on page 64
vª1050 Mini PCI adapterº on page 70
vª1060 Keyboardº on page 73
vª1100 Hinge coverº on page 87
vª1150 LCD assemblyº on page 98
vª2020 LCD front bezelº on page 120
vª2030 Inverter cardº on page 121
vª2040 LCD panel and LCD cable assemblyº on
page 122
1
1
Step Screw (quantity) Torque
«1¬M2.0 ý 3.5 mm, Silver (4) 0.196 Nm
(2 kgfcm)
Removing and replacing a FRU
124ThinkPad R40 
						

							To install the antenna assembly, do as follows:
1. Make sure that the antenna assembly and hinges are
firmly attached; there are some projections («a¬)onthe
hinges to fix the antenna assembly into place. And
then, route the gray cable
(MAIN)as in this figure.
a
333
(continued)
Removing and replacing a FRU
ThinkPad R40125 
						

							2. Route the black cable(AUX)as in figures«4¬and«5¬.
4
4
4
5
3. Secure the antenna assembly and hinges with screws
to the LCD cover.
Removing and replacing a FRU
126ThinkPad R40