HP Z800 Owners Manual

Screen messageProbable causeRecommended action
518—Power supply wattage
insufficient for hardware
configurationWorkstation configuration requires
more power than the power supply can
provide.●Reduce the workstation power consumption.
●Replace the power supply with a high output
power supply.
601—Diskette Controller ErrorDiskette controller circuitry or diskette
drive circuitry incorrect.1.Run the Computer Setup (F10) utility.
2.Verify cabling and replace defective cables if
necessary.
3.Clear CMOS....

Screen messageProbable causeRecommended action
925—Fatal error on IOH
miscellaneousFatal miscellaneous error detected on
IOH core x, where x is 0 or 1.Potential system board problem; contact HP Support.
926—Fatal error on IOH VtdFatal error detected in the Intel
Virtualization Technology.Potential system board problem; contact HP Support.
927—Fatal error on DIMM in
slot CPU X DIMM YFatal multibit ECC error detected on
the DIMM in the slot labeled CPU x
DIMM y (where x is 0 or 1 and y is 1 -
6), as...

Screen messageProbable causeRecommended action
ERROR: Mixing processors
with different power
requirements. This is not
supported. System halted.Mixed type processors detected.Replace the processors with matched processors.
Invalid electronic serial
numberIncorrect serial number registered in
the system.Use the Computer Setup (F10) Utility to reset the serial
number.
Mixing processors with
different power requirements.
This is not supported. System
halted.Mixed type processors detected.Replace the...

7 Configuring RAID devices
This chapter describes how to configure SAS and SATA RAID devices, and includes these topics:
Topics
Maximum hard drive configurations on page 202
Configuring SATA RAID devices on page 203
Configuring SAS RAID devices on page 207
For additional information about configuring RAIDs, see http://www.hp.com/support/RAID_FAQs. For
information about preparing the workstation for RAID configuration, see 
http://www.hp.com/support/
workstation_manuals.
Maximum hard drive configurations...

Configuring SATA RAID devices
This section describes how to use the Intel Matrix Storage Manager option ROM Configuration utility to
set up and manage SATA RAID volumes.
The following SATA RAID configurations are supported on this workstation:
●Up to the workstation-specific maximum number of internal SATA hard disk drives and eSATA
drives (if you use an optional eSATA bulkhead cable)
●Intel Matrix Storage Manager (IMSM) for Windows
If only a single HDD is attached, the Intel Matrix Storage Manager...

Configuring system BIOS
Configure the system BIOS to enable embedded SATA RAID functionality.
1.To enter the system BIOS setup, press F10.
2.Use the arrow keys to highlight the desired language, and then press Enter.
3.Use the arrows to highlight Storage>Storage Options, and then press Enter.
4.Use the up or down arrow key to highlight SATA Emulation.
5.Use the left or right arrow key to select RAID+AHCI.
6.To accept the new setting, press F10.
7.Use the arrows to highlight Advanced>Power-On Options, and...

Creating RAID volumes
To create RAID volumes, use the Intel Matrix Storage Manager option ROM Configuration utility.
1.To enter the Intel Matrix Storage Manager option ROM Configuration utility, press Ctrl+l when
prompted
2.If required, see 
Deleting RAID volumes on page 206 to make enough physical drives available to
create the RAID volume.
3.Use the up or down arrow key to highlight 1. Create RAID Volume, and then press Enter.
4.Type the desired RAID volume name in the Name: field, and then press Tab....

Deleting RAID volumes
Use the LSI Logic Corporation Configuration Utility to delete SAS RAID volumes.
1.Start the LSI Corporation Configuration Utility. During BIOS start up, you are prompted to Press
Ctrl-C to start LSI Corp. Configuration Utility.
2.On the Main menu of the BIOS-based configuration utility, use the arrow keys to select an adapter.
3.Press Enter to go to the Adapter Properties screen.
4.In the Select New Array Type screen, use the arrow keys to select New Existing Array.
5.In the View...

Configuring SAS RAID devices
Supported configurations
The following RAID configurations are supported on this workstation:
NOTE: This section does not apply to configuring SAS RAID in the Linux environment. For Linux SAS
RAID information, including supported configurations, refer to Installing and Configuring SAS Hardware
RAID on HP Linux Workstations at 
http://www.hp.com/support/xw8600_manuals.
●Up to the workstation-specific maximum number of internal SAS hard disk drives
●LSI MegaRAID Storage Manager...

SAS RAID 0 configuration
Use the following procedure to configure an Integrated Striped (IS) volume with the BIOS-based
configuration utility. The procedure assumes that the system has the required disk and disk controllers.
1.Start the LSI Corporation Configuration Utility. During BIOS start up, you are prompted to Press
Ctrl-C to start LSI Corp. Configuration Utility.
2.On the Main menu of the BIOS-based configuration utility, use the arrow keys to select an adapter.
3.Press Enter to go to the Adapter...