HP Proliant Dl380 Generation 5 Server User Guide
Have a look at the manual HP Proliant Dl380 Generation 5 Server User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Operations 21 WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack is adequately stabilized before extending a component from the rack. 3. After performing the installation or maintenance procedure, slide the server back into the rack: a. Press the server rail-release latches and slide the server fully into rack. WARNING: To reduce the risk of personal injury, be careful when pressing the server rail-release latches and sliding the server into the rack. The sliding rails could pinch your fingers. b. Press the server firmly into the rack to secure it in place. Remove the access panel WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal damage.
Operations 22 To remove the component: 1. Power down the server if performing a non-hot- plug installation or maintenance procedure (Power down the server on page 20). 2. Extend the server from the rack (on page 20). 3. Use the T-15 Torx screwdriver attached to the rear of the server to loosen the security screw on the hood latch. 4. Lift up on the hood latch handle and remove the access panel. Install the access panel 1. Place the access panel on top of the server with the hood latch open. Allow the panel to extend past the rear of the server approximately 1.25 cm (0.5 in). 2. Push down on the hood latch. The acce ss panel slides to a closed position. 3. Use the T-15 Torx screwdriver attached to the rear of the server to tighten the security screw on the hood latch. Remove the PCI riser cage CAUTION: To prevent damage to the server or expansio n boards, power down the server and remove all AC power cords before removing or installing the PCI riser cage. 1. Power down the server (on page 20). 2. Extend the server from the rack (on page 20). 3. Remove the access panel (on page 21). 4. Disconnect any internal or external cables connected to any existing expansion boards. 5. Press the blue button to release the black knob. 6. Turn the black knob counter-clockwise. 7. Remove the PCI riser cage.
Operations 23 Install the PCI riser cage CAUTION: To prevent damage to the server or expansio n boards, power down the server and remove all AC power cords before removing or installing the PCI riser cage. 1. Align the PCI riser cage with the chassis and slide it into place. 2. Tighten the thumbscrews to secure the PCI riser cage: a. Press down the black knob while turning clockwise, until fully tightened. b. While holding the black knob and pressing down, press and release the blue button to lower the black knob to the locked position. 3. Connect any required internal cabl es to the expansion board. Refer to the documentation that ships with the expansion board. 4. Install the access panel (on page 22). 5. Install the server into the rack. 6. Connect any required external cables to the expansi on board. Refer to the documentation that ships with the expansion board.
Operations 24 7. Power up the server (on page 20). Access the product rear panel Cable management arm with left-hand swing To access the server rear panel, open the cable management arm. Cable management arm with right-hand swing NOTE: To access some components, you may ne ed to remove the cable management arm. To access the product rear panel components, open the cable management arm: 1. Power down the server (on page 20). 2. Swing open the cable management arm. 3. Remove the cables from the cable trough.
Operations 25 4. Remove the cable management arm. Hot-plug fan operation The server supports variable fan speeds to allow the speed of all fans to increase if the temperature in any area increases. The fans will run at minimum spee d until a temperature change requires a fan speed increase to cool the server. The server shuts down in the following scenarios: • At POST: • The BIOS suspends the server for 5 minutes if it detects a cautionary temperature level. If the cautionary temperature level is still detected after 5 minutes, the BIOS performs an orderly shutdown and enters Standby mode. • The BIOS performs an orderly shutdown if fewer than 11 fans are operating. • The server performs an immediate shutdown if it detects a critical temperature level. IMPORTANT: An immediate shutdown is a hardware-control led function and it overrides any firmware or software actions. • In the operating system: • The Health Driver performs an orderly shutdown if it detects a cautionary temperature level. If the server detects a critical temperature level before the orderly shutdown occurs, the server performs an immediate shutdown. Additionally, the Health Driver performs an orderly shutdown if more than one fan is failed or removed. • When Thermal Shutdown is disabled in RBSU, the server performs an immediate shutdown if it detects a critical temperature level. IMPORTANT: An immediate shutdown is a hardware-control led function and it overrides any firmware or software actions.
Setup 26 Setup In this section Optional installa tion services ........................................................................\......................... .................. 26 Rack planning resources ........................................................................\................................ ................. 27 Optimum envi ronment........................................................................\.................................... ................. 27 Rack warnings ........................................................................\.......................................... ..................... 29 Identifying the contents of the server shipping carton ........................................................................\. ......... 29 Installing hard ware options ........................................................................\............................ ................. 29 Installing the serv er into the rack ........................................................................\.................... .................. 29 Installing the op erating system ........................................................................\........................ ................. 32 Powering up and conf iguring the server ........................................................................\................. ........... 32 Registering the server........................................................................\................................. ..................... 32 Optional installation services Delivered by experienced, certified engineers, HP Care Pack servic es help you keep your servers up and running with support packages tailored specifically for HP ProLiant systems. HP Care Packs let you integrate both hardware and software support into a single package. A number of service level options are available to meet your needs. HP Care Pack Services offer upgr aded service levels to expand your standard product warranty with easy- to-buy, easy-to-use support packages that help you make the most of your server investments. Some of the Care Pack services are: • Hardware support • 6-Hour Call-to-Repair • 4-Hour 24x7 Same Day • 4-Hour Same Business Day • Software support • Microsoft® • Linux • HP ProLiant Essentials (HP SIM and RDP) • VMWare • Integrated hardware and software support • Critical Service • Proactive 24 • Support Plus • Support Plus 24 • Startup and implementation services for both hardware and software For more information on Care Packs, refer to the HP website ( http://www.hp.com/hps/carepac k/servers/cp_proliant.html ).
Setup 27 Rack planning resources The rack resource kit ships with all HP branded or Compaq branded 9000, 10000, and H9 series racks. For more information on the content of each resour ce, refer to the rack resource kit documentation. If you intend to deploy and config ure multiple servers in a single rack, refer to the white paper on high- density deployment at the HP website ( http://www.hp.com/products/servers/platforms ). Optimum environment When installing the server in a rack, select a locati on that meets the environmental standards described in this section. Space and airflow requirements To allow for servicing and adequate airflow, observe the following space and airflow requirements when deciding where to install a rack: • Leave a minimum clearance of 63.5 cm (25 in) in front of the rack. • Leave a minimum clearance of 76.2 cm (30 in) behind the rack. • Leave a minimum clearance of 121.9 cm (48 in) from the back of the rack to the back of another rack or row of racks. HP servers draw in cool air through the front door and expel warm air through the rear door. Therefore, the front and rear rack doors must be adequately ventilated to allow ambient room air to enter the cabinet, and the rear door must be adequately vent ilated to allow the warm air to escape from the cabinet. CAUTION: To prevent improper cooling and damage to the equipment, do not block the ventilation openings. When vertical space in the rack is not filled by a server or rack component, the gaps between the components cause changes in airflow through the ra ck and across the servers. Cover all gaps with blanking panels to maintain proper airflow. CAUTION: Always use blanking panels to fill empty vertic al spaces in the rack. This arrangement ensures proper airflow. Using a rack without blanking panels results in improper cooling that can lead to thermal damage. The 9000 and 10000 Series Racks provide proper server cooling from flow-through perforations in the front and rear doors that provide 64 percent open area for ventilation. CAUTION: When using a Compaq branded 7000 Series rack, you must install the high airflow rack door insert [P/N 327281-B21 (42U) or P/N 157847-B21 (22U )] to provide proper front-to-back airflow and cooling. CAUTION: If a third-party rack is used, observe the fo llowing additional requirements to ensure adequate airflow and to prevent damage to the equipment: • Front and rear doors—If the 42U rack includes clos ing front and rear doors, you must allow 5,350 sq cm (830 sq in) of holes evenly distributed from top to bottom to permit adequate airflow (equivalent to the required 64 percent open area for ventilation). • Side—The clearance between the installed rack comp onent and the side panels of the rack must be a minimum of 7 cm (2.75 in). IMPORTANT: The HP ProLiant DL380 Generation 5 Server cable management arm is not supported on Compaq branded 7000 series racks.
Setup 28 Temperature requirements To ensure continued safe and reliable equipment oper ation, install or position the system in a well- ventilated, climate-controlled environment. The maximum recommended ambient operating temperat ure (TMRA) for most server products is 35°C (95°F). The temperature in the room where the rack is located must not exceed 35°C (95°F). CAUTION: To reduce the risk of damage to the equi pment when installing third-party options: • Do not permit optional equipment to impede airflow around the server or to increase the internal rack temperature beyond the maximum allowable limits. • Do not exceed the manufacturer’s TMRA. Power requirements Installation of this equipment must comply with lo cal and regional electrical regulations governing the installation of information technology equipment by li censed electricians. This equipment is designed to operate in installations covered by NFPA 70, 1999 Ed ition (National Electric Code) and NFPA-75, 1992 (code for Protection of Electronic Computer/Data Proc essing Equipment). For electrical power ratings on options, refer to the product rating label or th e user documentation supplied with that option. WARNING: To reduce the risk of personal injury, fire, or damage to the equipment, do not overload the AC supply branch circuit th at provides power to the rack. Consult the electrical authority having jurisdiction over wiring and installation requirements of your facility. CAUTION: Protect the server from power fluctuations and temporary interruptions with a regulating uninterruptible power supply (UPS). This device pr otects the hardware from damage caused by power surges and voltage spikes and keeps the syst em in operation during a power failure. When installing more than one server, you may need to use additional power distribution devices to safely provide power to all devices. Observe the following guidelines: • Balance the server power load between available AC supply branch circuits. • Do not allow the overall system AC current load to exceed 80 percent of the branch circuit AC current rating. • Do not use common power outlet strips for this equipment. • Provide a separate electrical circuit for the server. Electrical grounding requirements The server must be grounded properly for proper operation and safety. In the United States, you must install the equipment in accordance with NFPA 70, 1999 Edition (National Electric Code), Article 250, as well as any local and regional building codes. In Canada, you must install the equipment in accordance with Canadian Standards Association, CS A C22.1, Canadian Electrical Code. In all other countries, you must install the equipment in accordance with any regional or national electrical wiring codes, such as the International Electrotechnical Commission (IEC) Code 364, parts 1 through 7. Furthermore, you must be sure that all power distributi on devices used in the installation, such as branch wiring and receptacles, are listed or certified grounding-type devices. Because of the high ground-leakage currents associ ated with multiple servers connected to the same power source, HP recommends the use of a PDU that is either permanently wired to the building’s branch circuit or includes a nondetachable co rd that is wired to an industrial-style plug. NEMA locking-style plugs or those complying with IEC 60309 are considered su itable for this purpose. Using common power outlet strips for the server is not recommended.
Setup 29 Rack warnings WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • The leveling jacks are extended to the floor. • The full weight of the rack rests on the leveling jacks. • The stabilizing feet are attached to the ra ck if it is a single-rack installation. • The racks are coupled together in multiple-rack installations. • Only one component is extended at a time. A rack may become unstable if more than one component is extended for any reason. WARNING: To reduce the risk of personal injury or equipment damage when unloading a rack: • At least two people are needed to safely unload the rack from the pallet. An empty 42U rack can weigh as much as 115 kg (253 lb), can stand more than 2.1 m (7 ft) tall, and may become unstable when being moved on its casters. • Never stand in front of the rack when it is rolling down the ramp from the pallet. Always handle the rack from both sides. Identifying the contents of the server shipping carton Unpack the server shipping carton and locate the mate rials and documentation necessary for installing the server. All the rack mounting hardware necessary for inst alling the server into the rack is included with the rack or the server. The contents of the server shipping carton include: • Server • Power cord • Hardware documentation, Document ation CD, and software products • Rack-mounting hardware In addition to the supplied items, you may need: • Operating system or application software • Hardware options Installing hardware options Install any hardware options before initializing the serv er. For options installation information, refer to the option documentation. For server-specific informatio n, refer to Hardware options installation (on page 33 ). Installing the server into the rack CAUTION: Always plan the rack installation so that the heaviest item is on the bottom of the rack. Install the heaviest item first, and continue to po pulate the rack from the bottom to the top. 1. Install the server and cable management arm into the rack. For more information, refer to the installation instructions that ship with the 2U Quick Deploy Rail System.
Setup 30 2. Connect peripheral devices to the server. Item Description Color 1 Expansion slot 1 — 2 Expansion slot 2 — 3 Expansion slot 3 — 4 Expansion slot 4 — 5 Expansion slot 5 — 6 T-10/T-15 Torx screwdriver — 7 External option blank — 8 NIC 2 connector — 9 NIC 1 connector — 10 Power supply bay 2 — 11 Power cord connector Black 12 Power supply bay 1 (populated) — 13 iLO 2 connector — 14 Video connector Blue 15 USB connectors (2) Black 16 Serial connector — 17 Mouse connector Green 18 Keyboard connector Purple WARNING: To reduce the risk of electric sh ock, fire, or damage to the equipment, do not plug telephone or telecommunications connectors into RJ-45 connectors. 3. Connect the power cord to the rear of the server.