HP Photosmart C5383 User Manual

Chapter 3
18 Find more information
Find more information
 

4 Finish setting up the HP All-in-One
After you have completed the steps in your Start Here guide, refer to this section to help
you finish setting up the HP All-in-One. This section contains important setup-related
information for your product.
This section contains the following topics:
•
Set your preferences
•
Computer connection information
•
Connect to a Bluetooth® device
Set your preferences
Before you begin using your product, you should review and, if necessary, adjust the
general settings...

5.When prompted, press the down arrow button to highlight  Yes for confirmation, and
then press  OK.
The  Preferences  menu reappears.
6. Press the down arrow button to highlight  Set Country/Region, and then press OK.
7. Press the down arrow button to scroll through the countries/regions. When the
country/region you want to use is highlighted, press  OK.
8. When prompted, press the down arrow button to highlight  Yes for confirmation, and
then press  OK.
Set the default paper tray for...

3.Press the down arrow button to highlight  Enable Faster Browsing, and then press
OK .
4. Press the down arrow or the up arrow button to highlight  On or  Off, and then press
OK .
Set the energy save mode
When you turn off the HP All-in-One, it goes into Energy Save mode by default. This
makes the product more energy efficient, but also means it can take longer than expected
to turn the product on. Additionally, when turned off in Energy Save mode, the HP All-in-
One might not be ab le to complete some...

NOTE:Restoring the factory defaults will not affect any changes you made to scan
settings and the language and country/region settings.
You can perform this process from the control panel only.
To restore the factory defaults
1. Press  Setup.
2.Press the down arrow button to highlight  Tools, and then press  OK.
3. Press the down arrow button to highlight  Restore Factory Defaults, and then press
OK .
The factory default settings are restored.
Play a slideshow on the display
You can set up the HP...

To turn the tips slideshow on or off
1.Press  Setup.
2.Press the down arrow button to highlight  Tools, and then press  OK.
3. Press the down arrow button to highlight  Tips Slideshow, and then press  OK.
4. Press the down arrow or the up arrow button to highlight  On or  Off, and then press
OK .
Computer connection information
The HP All-in-One comes equipped with a rear USB 2.0 High Speed port for connection
to a computer.
If you use a USB cable to connect the HP All-in-One to a computer on a network,...

What you need for a Bluetooth connection
To connect the HP All-in-One with a Bluetooth connection, you will need the following:
❑A Bluetooth capable device (such as a PDA, camera phone, or computer)
❑ An HP Bluetooth Adapter
Some Bluetooth products exchange device addresses when they communicate with each
other, so you might also need to find out the device address of the HP All-in-One in order
to establish a connection.
To find out the device address of the product
1. Insert the HP Bluetooth Adapter...

the HP All-in-One. It is possible to have both the Microsoft Stack and the Widcomm Stack
on your computer, but you use only one of them to connect the HP All-in-One.
•Microsoft stack : If you have Windows Vista or Windows XP with Service Pack 2
installed on your computer, then your computer has the Microsoft Bluetooth
® Protocol
Stack. The Microsoft stack allows you to install an external Bluetooth® adapter
automatically. If your Bluetooth® adapter supports the Microsoft stack but it does not
install...

To install and print using the Widcomm stack
1.Make sure that you have installed the product software on the computer.
NOTE: The purpose of installing the software is to make sure the printer driver
is available for the Bluetooth® connection. Therefore, if you have already installed
the software, you do not need to reinstall it. If you want both a USB and a
Bluetooth
® connection to the product, install the USB connection first. For more
information, see the Start Here guide. However, if you do not want...

The following table describes the Bluetooth settings shown on the configuration page.
ParameterDescription
Device AddressThe hardware address of the Bluetooth device.
Device NameThe device name assigned to the product, which can identify it on a Bluetooth
device.
PasskeyA value that the user must enter in order to print via Bluetooth.
VisibilityShows whether or not the HP All-in-One is visible to Bluetooth devices that
are within range.
•Visible to all : Any Bluetooth device within range can print to...