HP Photosmart C4783 User Manual

							Solution 3: Make sure the protective tape is removed from the print cartridges
Solution:Check each print cartridge. The tape might have been removed from the
copper-colored contacts, but still might cover the ink nozzles. If the tape is still
covering the ink nozzles, carefully remove the tape from the print cartridges. Do not
touch the ink nozzles or the copper-colored contacts.
1Copper-colored contacts
2Plastic tape with pink pull tab (must be removed before installing)
3Ink nozzles under tape
Remove and then reinsert the print cartridges. Verify that they are fully inserted and
locked in place.
Cause:Protective tape was covering the print cartridges.
If this did not solve the issue, try the next solution.
Solution 4: Check if print cartridges are fully inserted
Solution:Remove and then reinsert the print cartridges. Verify that they are fully
inserted and locked in place.
Cause:The contacts on the print cartridge were not touching the contacts in the
print carriage.
If this did not solve the issue, try the next solution.
Errors 79
Solve a problem
 
						

							Solution 5: Print cartridge might be defective
Solution:If the alignment error persists and you cannot clear it, your print cartridge
might be defective. Check to see if your print cartridge is still under warranty and end
of warranty date has not been reached.
•If the end of warranty date has been reached, purchase a new print cartridge.
•If the end of warranty date has not been reached, contact HP support. Go to
www.hp.com/support. If prompted, choose your country/region, and then click
Contact HP for information on calling for technical support.
For more information, see:
•“
Cartridge warranty information” on page 51
•“
Order ink supplies” on page 50
Cause:The print cartridge was defective.
Print cartridges incorrectly installed
Solution:Remove and reinsert the print cartridges and verify that they are fully
inserted and locked in place.
Also, make sure the print cartridges are installed into the correct slots.
To make sure the print cartridges are installed correctly
1.Make sure the product is turned on.
CAUTION:If the product is turned off when you open the print cartridge door
to access the print cartridges, it will not release the cartridges for changing.
You might damage the product if the print cartridges are not docked safely
when you try to remove them.
2.Open the print cartridge door.
The print carriage moves to the far right side of the product.
3.Check to make sure you are using the correct print cartridges for your product.
For a list of compatible print cartridges, see the printed documentation that came
with the product.
Chapter 12
80 Solve a problem
Solve a problem
 
						

							4.Remove the black print cartridge from the slot on the right. Do not touch the ink
nozzles or the copper-colored contacts. Check for possible damage to the copper-
colored contacts or ink nozzles.
Make sure the clear plastic tape has been removed. If it is still covering the ink
nozzles, gently remove the clear plastic tape by using the pink pull tab. Make sure
you do not remove the copper colored tape containing the electrical contacts.
1Copper-colored contacts
2Plastic tape with pink pull tab (must be removed before installing)
3Ink nozzles under tape
5.Reinsert the print cartridge by sliding it forward into the slot on the right. Then
push the print cartridge forward until it clicks into the socket.
6.Repeat steps 1 and 2 for the tri-color print cartridge on the left side.
Cause:The indicated print cartridges were installed incorrectly.
Non-HP cartridges installed
Solution:Follow the prompts on the display to continue, or replace the indicated
print cartridges with genuine HP cartridges.
Errors 81
Solve a problem
 
						

							HP recommends that you use genuine HP print cartridges. Genuine HP print
cartridges are designed and tested with HP printers to help you easily produce great
results, time after time.
NOTE:HP cannot guarantee the quality or reliability of non-HP supplies. Printer
service or repairs required as a result of using of a non-HP supply will not be
covered under warranty.
If you believe you purchased genuine HP print cartridges, go to:
www.hp.com/go/anticounterfeit
For more information, see:
“
Replace the cartridges” on page 48
Cause:The product detected that a non-HP print cartridge was installed.
Print cartridge is missing, incorrectly installed, or not intended for your product
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Insert the print cartridges
•
Solution 2: Remove the tape from the print cartridges
•
Solution 3: Remove and reinsert the print cartridges
•
Solution 4: Contact HP support
Solution 1: Insert the print cartridges
Solution:One or both of the print cartridges is missing. Remove and reinsert the
print cartridges and verify that they are fully inserted and locked in place. If the
problem persists, clean the contacts of the print cartridges.
To clean the print cartridge contacts
1.Turn on the product and open the print cartridge door.
The print carriage moves to the far right side of the product.
2.Wait until the print carriage is idle and silent, and then unplug the power cord from
the back of the product.
Chapter 12
82 Solve a problem
Solve a problem
 
						

							3.Lightly press down on the print cartridge to release it, and then pull it towards you
out of the slot.
NOTE:Do not remove both print cartridges at the same time. Remove and
clean each print cartridge one at a time. Do not leave a print cartridge outside
the HP Photosmart for more than 30 minutes.
4.Inspect the print cartridge contacts for ink and debris buildup.
5.Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze
any excess water from it.
6.Hold the print cartridge by its sides.
7.Clean only the copper-colored contacts. Allow the print cartridges to dry for
approximately ten minutes.
1Copper-colored contacts
2Ink nozzles (do not clean)
8.Hold the print cartridge with the HP logo on top, and insert the print cartridge back
into the slot. Make sure you push the print cartridge in firmly until it snaps into
place.
Errors 83
Solve a problem
 
						

							9.Repeat if necessary for the other print cartridge.
10.Gently close the print cartridge door and plug the power cord into the back of the
product.
Cause:The print cartridge was missing.
If this did not solve the issue, try the next solution.
Solution 2: Remove the tape from the print cartridges
Solution:Check each print cartridge. The tape might have been removed from the
copper-colored contacts, but still might cover the ink nozzles. If the tape is still
covering the ink nozzles, carefully remove the tape from the print cartridges. Do not
touch the ink nozzles or the copper-colored contacts.
1Copper-colored contacts
2Plastic tape with pink pull tab (must be removed before installing)
3Ink nozzles under tape
Cause:Protective tape was covering the print cartridges.
If this did not solve the issue, try the next solution.
Chapter 12
84 Solve a problem
Solve a problem
 
						

							Solution 3: Remove and reinsert the print cartridges
Solution:One or both of the print cartridges are not installed or are installed
incorrectly. Remove and reinsert the print cartridges and verify that they are fully
inserted and locked in place. If the problem persists, clean the copper-colored
contacts of the print cartridges.
To clean the print cartridge contacts
1.Turn on the product and open the print cartridge door.
The print carriage moves to the center of the product.
2.Wait until the print carriage is idle and silent, and then unplug the power cord from
the back of the product.
3.Lightly press down on the print cartridge to release it, and then pull it towards you
out of the slot.
NOTE:Do not remove both print cartridges at the same time. Remove and
clean each print cartridge one at a time. Do not leave a print cartridge outside
the HP Photosmart for more than 30 minutes.
4.Inspect the print cartridge contacts for ink and debris buildup.
5.Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze
any excess water from it.
6.Hold the print cartridge by its sides.
7.Clean only the copper-colored contacts. Allow the print cartridges to dry for
approximately ten minutes.
1Copper-colored contacts
2Ink nozzles (do not clean)
Errors 85
Solve a problem
 
						

							8.Hold the print cartridge with the HP logo on top, and insert the print cartridge back
into the slot. Make sure you push the print cartridge in firmly until it snaps into
place.
9.Repeat if necessary for the other print cartridge.
10.Gently close the print cartridge door and plug the power cord into the back of the
product.
Cause:One or both of the print cartridges were not installed or were installed
incorrectly.
If this did not solve the issue, try the next solution.
Solution 4: Contact HP support
Solution:Contact HP support for service.
Go to: 
www.hp.com/support.
If prompted, choose your country/region, and then click Contact HP for information
on calling for technical support.
Cause:The print cartridge was defective or not intended for use in this product.
Printing in ink-backup mode
Solution:If you receive the ink-backup mode message and two print cartridges are
installed in the product, verify that the protective piece of plastic tape has been
Chapter 12
86 Solve a problem
Solve a problem
 
						

							removed from each print cartridge. When plastic tape covers the print cartridge
contacts, the product cannot detect that the print cartridge is installed.
1Copper-colored contacts
2Plastic tape with pink pull tab (must be removed before installing)
3Ink nozzles under tape
Cause:When the product detected that only one print cartridge is installed, ink-
backup mode is initiated. This printing mode lets you print with a single print cartridge,
but it slows the product and affects the quality of printouts.
Print cartridges missing or not detected
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Reinsert the print cartridges
•
Solution 2: Clean the print cartridge contacts
•
Solution 3: Replace the print cartridge
Solution 1: Reinsert the print cartridges
Solution:Remove and reinsert the print cartridges and verify that they are fully
inserted and locked in place.
Errors 87
Solve a problem
 
						

							Also, make sure the print cartridges are installed into the correct slots.
To make sure the print cartridges are installed correctly
1.Make sure the product is turned on.
CAUTION:If the product is turned off when you open the print cartridge door
to access the print cartridges, it will not release the cartridges for changing.
You might damage the product if the print cartridges are not docked safely
when you try to remove them.
2.Open the print cartridge door.
The print carriage moves to the far right side of the product.
3.Check to make sure you are using the correct print cartridges for your product.
For a list of compatible print cartridges, see the printed documentation that came
with the product.
4.Remove the black print cartridge from the slot on the right. Do not touch the ink
nozzles or the copper-colored contacts. Check for possible damage to the copper-
colored contacts or ink nozzles.
Make sure the clear plastic tape has been removed. If it is still covering the ink
nozzles, gently remove the clear plastic tape by using the pink pull tab. Make sure
you do not remove the copper colored tape containing the electrical contacts.
1Copper-colored contacts
2Plastic tape with pink pull tab (must be removed before installing)
3Ink nozzles under tape
Chapter 12
88 Solve a problem
Solve a problem