HP Photosmart C4480 User Manual

File corrupted
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Reinsert the memory card in the product
•
Solution 2: Reformat the memory card in your digital camera.
Solution 1: Reinsert the memory card in the product Solution: Reinsert the memory card in the product. If this does not work, retake the...

Cannot crop
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Close some applications or restart your computer
•
Solution 2: Empty the Re cycle Bin on your desktop
Solution 1: Close some applications or restart your computer Solution: Close all unnecessary applications. This includes applications that run...

Cause:There were two or more memory cards inserted into the product at the same
time.
If this did not solve the issue, try the next solution.
Solution 2: Push the memory card all the way forward
Solution: Remove the memory card and reinsert  it in the memory card slot until it
stops.
Cause: You had not fully inserted the memory card.
Disconnected
Solution: Make sure your computer is turned on and is connected to the product.
Also make sure you installed the software that came with the product.
For more...

Solution 2: Push the memory card all the way forwardSolution: Remove the memory card and reinsert  it in the memory card slot until it
stops.
Cause: You had not fully inserted the memory card.
Use only one card at a time
Solution: You can insert only one memory card at a time.
If more than one memory card is inserted, the green Photo light (near the memory
card slots) will blink rapidly, and an error message will appear on the computer screen.
Remove the additional memory card to resolve the problem....

If the memory card is not inserted properly, the product will not respond and the green
Photo light (near the memory card slots) will blink rapidly.
After the memory card has been inserted properly, the Photo light will blink green for
a few seconds, and then remain lit.
Cause:The memory card was not fully inserted.
Paper messages
The following is a list of  paper-related error messages:
•
Paper upside down
•
Paper orientation error
•
Cannot load paper from input tray
•
Ink is drying
•
Out of paper
•...

Out of paper
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Replace the rear door
•
Solution 2: Make sure the paper is loaded correctly
•
Solution 3: Check the print settings
•
Solution 4: Clean the paper feed rollers with the HP Paper Feed Cleaning Kit
•
Solution 5: Clean the rollers
•
Solution 6:...

For more information, see:
•“
Set the paper type for printing” on page 31
•“
Change the print speed or quality” on page 32
•“
Print using Maximum dpi” on page 39
•“
Change copy speed or quality” on page 57
Cause: The paper type or print quality settings were set incorrectly.
If this did not solve the issue, try the next solution.
Solution 4: Clean the paper feed rollers with the HP Paper Feed Cleaning Kit Solution: Some inkjet products require a special kit, called the HP Paper Feed
Cleaning Kit, to...

6.Plug the power cord back in, and turn on the product.
7. Try to print again.
Cause: The rollers were dirty and needed to be cleaned.
If this did not solve the issue, try the next solution.
Solution 6: Contact HP support for service Solution: If you have completed all of the steps provided in the previous solutions
and are still having a problem, contact HP support for service.
Go to: 
www.hp.com/support .
If prompted, choose your country/region, and then click  Contact HP for technical
support.
Cause:...

4.Press  OK on the control panel to continue the current job.
Cause: Paper had jammed in the product.
Paper mismatch
Solution: Change the print setting or load the appropriate paper in the input tray.
• Do not use paper that is too thin, that has a slick texture, or that stretches easily.
It can feed incorrectly through the paper path, causing paper jams.
• Store photo media in its original packaging inside a resealable plastic bag on a
flat surface in a cool, dry place. When you are ready to print,...

Product not foundSolution: If the product is not properly connected to the computer, communication
errors can occur. Make sure the USB cable is securely connected to the product and
the computer, as shown below.
Cause: The USB cable was not plugged in properly.
Communication test failed
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the...