HP Pavilion Dv8 1100 Entertainment Notebook Pc Series Manual

Removal and replacement procedures
Maintenance and Service Guide4–37
9. If it is necessary to replace the webcam/microphone module:
a. Remove the Phillips PM2.0×4.0 screw 1 that secures the module to the display bezel.
b. Release the webcam/microphone module 2 as far from the display bezel as the webcam/microphone 
module cable allows.
c. Disconnect the webcam/microphone module cable 3 from the webcam/microphone module, and remove 
the webcam/microphone module. The webcam/microphone module is available...

4–38Maintenance and Service Guide
Removal and replacement procedures
11. If it is necessary to replace the webcam/microphone module cable, remove the cable from the display panel. 
The webcam/microphone module cable is included in the Display Cable Kit, spare part number 496876-001.
12. If it is necessary to replace the display panel cable:
a. Detach the adhesive reinforcement strip 1 that secures the display panel cable to the display panel.
b. Disconnect the display panel cable 2 from the display...

Removal and replacement procedures
Maintenance and Service Guide4–39
13. If it is necessary to replace the display inverter:
a. Release the display inverter 1 as far from the display bezel as the backlight cables and display panel 
cable allow.
b. Disconnect the two backlight cables 2 and the display panel cable 3 from the display inverter, and remove 
the display inverter. The display inverter is available using spare part number 498324-001.
14. If it is necessary to replace the display hinges:
a....

4–40Maintenance and Service Guide
Removal and replacement procedures
c. Remove the four Phillips PM2.0×4.0 screws 1 that secure the display hinges to the display panel.
d. Remove the four Phillips PM2.5×7.0 screws 2 that secure the display hinges to the display panel.
e. Remove the display hinges 3. The display hinges and display hinge bracket are included in the Display 
Hinge Kit, spare part number 496874-001.
Reverse this procedure to reassemble and install the display assembly. 

Removal and replacement procedures
Maintenance and Service Guide4–41
Top cover
Before removing the top cover, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then 
unplugging the AC adapter from the...

4–42Maintenance and Service Guide
Removal and replacement procedures
Remove the top cover: 
1. Turn the computer upside down, with the front toward you.
2. Remove the 14 Phillips PM2.5×7.0 screws that secure the top cover to the base enclosure.
3. Remove the three Phillips PM2.0×4.0 screws 1 in the mass storage device bay, and the four Phillips 
PM2.5×4.0 screws2 in the battery bay, that secure the top cover to the base enclosure.  

Removal and replacement procedures
Maintenance and Service Guide4–43
4. Turn the computer right-side up, with the front toward you.
5. Disconnect the following cables from the system board:
1 TouchPad board cable
2 TouchPad on/off button board cable
3 USB board cable
4 Power connector cable
6. Release the power connector cable 1 and USB board cable 2 from the clips and routing channel built into the 
top cover. 

4–44Maintenance and Service Guide
Removal and replacement procedures
7. Remove the five Phillips PM2.5×7.0 screws that secure the top cover to the base enclosure. 
8. Lift the rear edge 1 of the top cover until it rests at an angle.
9. Slide the top cover 2 back until the fingerprint reader board cable is accessible. 

Removal and replacement procedures
Maintenance and Service Guide4–45
10. Release the ZIF connector 1 to which the fingerprint reader board cable is attached, and disconnect the 
fingerprint reader board cable from the system board.
11. Remove the top cover 2.
Reverse this procedure to install the top cover. 

4–46Maintenance and Service Guide
Removal and replacement procedures
TouchPad on/off button board
Before removing the TouchPad on/off button board, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then...