HP Pavilion Dv8 1100 Entertainment Notebook Pc Series Manual

Removal and replacement procedures
Maintenance and Service Guide4–7
Battery
Before removing the battery, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then 
unplugging the AC adapter from the computer....

4–8Maintenance and Service Guide
Removal and replacement procedures
Optical drive
✎The optical drive spare part kit includes an optical drive bezel and bracket.
Before removing the optical drive, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging...

Removal and replacement procedures
Maintenance and Service Guide4–9
5. If it is necessary to replace the optical drive bracket:
a. Position the optical drive with the rear toward you. 
b. Remove the two Phillips PM2.0×4.0 screws 1 that secure the optical drive bracket to the optical drive. 
c. Remove the optical drive bracket 2. 
Reverse this procedure to reassemble and install an optical drive.  

4–10Maintenance and Service Guide
Removal and replacement procedures
Mass storage device
✎The mass storage device spare part kit includes a left and right bracket, Mylar sleeve, connector, and 4 isolators. 
Before removing the mass storage devices, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3....

Removal and replacement procedures
Maintenance and Service Guide4–11
Remove the mass storage devices:
1. Loosen the five Phillips PM2.5×6.0 captive screws 1 that secure the mass storage device cover to 
the computer. 
2. Lift the rear edge of the mass storage device cover 2, swing it up and forward, and then remove the cover3. 
The mass storage device cover is included in the Plastics Kit, spare part number 580404-001.
3. Disconnect the mass storage device cable 1 from the system board.
4. Grasp the...

4–12Maintenance and Service Guide
Removal and replacement procedures
6. If it is necessary to replace the left and right brackets, Mylar sleeve, connector, and isolators:
a. Remove the two Phillips PM3.0×4.0 screws 1 from each side of the mass storage device.
b. Remove the left and right brackets 2.
c. Lift the Mylar sleeve 3 straight up to remove it from the mass storage device.
d. Remove the mass storage device connector 4.
e. Remove the four isolators 5.
Reverse this procedure to reassemble and...

Removal and replacement procedures
Maintenance and Service Guide4–13
TV tuner module
✎The TV tuner module spare part kit does not include a TV tuner module cable. The TV tuner module cable is 
included in the Cable Kit, spare part number 496891-001.
Before removing the TV tuner module, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external...

4–14Maintenance and Service Guide
Removal and replacement procedures
✎If the TV tuner module is removed and not replaced, a protective sleeve must be installed on the antenna 
connector, as shown in the following illustration.
Reverse this procedure to install the TV tuner module. 

Removal and replacement procedures
Maintenance and Service Guide4–15
RTC battery
Before removing the RTC battery, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then 
unplugging the AC adapter from the...

4–16Maintenance and Service Guide
Removal and replacement procedures
Memory module
Before removing the memory module, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then 
unplugging the AC adapter from...