HP Pavilion Dv8 1100 Entertainment Notebook Pc Series Manual

							Removal and replacement procedures
Maintenance and Service Guide4–7
Battery
Before removing the battery, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then 
unplugging the AC adapter from the computer. 
Remove the battery: 
1. Turn the computer upside down on a flat surface, with the front toward you.
2. Slide the battery release latch 1 to release the battery.
3. Pivot the battery 2 upward and remove it 3 from the computer.
To insert the battery, insert the rear edge of the battery into the battery bay, and pivot the front edge of the battery 
downward until it is seated. The battery release latch automatically locks the battery into place.
DescriptionSpare part number
8-cell, 73-Wh Li-ion battery480385-001
4-cell, 63-Wh Li-ion battery516916-001 
						

							4–8Maintenance and Service Guide
Removal and replacement procedures
Optical drive
✎The optical drive spare part kit includes an optical drive bezel and bracket.
Before removing the optical drive, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-7). 
Remove the optical drive: 
1. Position the computer with the left side toward you. 
2. Remove the Phillips PM2.5×7.0 screw 1 that secures the optical drive to the computer. 
3. Insert a paper clip or similar tool into the optical drive tab access 2, and push the tab forward to release the 
optical drive from the computer. 
4. Remove the optical drive 3 from the computer. 
Description Spare part number 
Blu-ray ROM with LightScribe DVD±RW SuperMulti DL Drive 503488-001
Blu-ray ROM DVD±RW SuperMulti DL Drive 503487-001 
						

							Removal and replacement procedures
Maintenance and Service Guide4–9
5. If it is necessary to replace the optical drive bracket:
a. Position the optical drive with the rear toward you. 
b. Remove the two Phillips PM2.0×4.0 screws 1 that secure the optical drive bracket to the optical drive. 
c. Remove the optical drive bracket 2. 
Reverse this procedure to reassemble and install an optical drive.  
						

							4–10Maintenance and Service Guide
Removal and replacement procedures
Mass storage device
✎The mass storage device spare part kit includes a left and right bracket, Mylar sleeve, connector, and 4 isolators. 
Before removing the mass storage devices, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-7). 
Description Spare part number 
Hard drive:
■500-GB, 7200-rpm577607-001
■500-GB, 5400-rpm501911-001
■320-GB, 7200-rpm507553-001
■320-GB, 5400-rpm503485-001
■250-GB, 7200-rpm507552-001
■250-GB, 5400-rpm503484-001
Solid-state drive:
■256-GB577609-001
■128-GB577608-001
Mass Storage Device Hardware Kit (includes left and right brackets, Mylar sleeve, connector, 
and 4 isolators)483862-001 
						

							Removal and replacement procedures
Maintenance and Service Guide4–11
Remove the mass storage devices:
1. Loosen the five Phillips PM2.5×6.0 captive screws 1 that secure the mass storage device cover to 
the computer. 
2. Lift the rear edge of the mass storage device cover 2, swing it up and forward, and then remove the cover3. 
The mass storage device cover is included in the Plastics Kit, spare part number 580404-001.
3. Disconnect the mass storage device cable 1 from the system board.
4. Grasp the Mylar tabs 2 on the mass storage device, and slide the mass storage device 3 away from the mass 
storage device connector.
5. Remove the mass storage device 4 from the mass storage device bay. 
						

							4–12Maintenance and Service Guide
Removal and replacement procedures
6. If it is necessary to replace the left and right brackets, Mylar sleeve, connector, and isolators:
a. Remove the two Phillips PM3.0×4.0 screws 1 from each side of the mass storage device.
b. Remove the left and right brackets 2.
c. Lift the Mylar sleeve 3 straight up to remove it from the mass storage device.
d. Remove the mass storage device connector 4.
e. Remove the four isolators 5.
Reverse this procedure to reassemble and install the mass storage devices. 
						

							Removal and replacement procedures
Maintenance and Service Guide4–13
TV tuner module
✎The TV tuner module spare part kit does not include a TV tuner module cable. The TV tuner module cable is 
included in the Cable Kit, spare part number 496891-001.
Before removing the TV tuner module, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-7). 
5. Remove the mass storage device cover (see “Mass storage device” on page 4-10). 
Remove the TV tuner module:
1. Disconnect the TV tuner module antenna cable 1 from the terminal on the TV tuner module.
2. Remove the two Phillips PM2.0×4.0 screws 2 that secure the TV tuner module to the system board. (The TV 
tuner module tilts up.)
3. Remove the TV tuner module 3 by pulling it away from the slot at an angle.
✎The TV tuner module is designed with a notch 4 to prevent incorrect insertion into the TV tuner 
module slot.
Description Spare part number 
DVB-T TV tuner module482899-003
DVB-T/ANG TV tuner module 482899-002
NTSC/ATSC/ANG TV tuner module 482899-001 
						

							4–14Maintenance and Service Guide
Removal and replacement procedures
✎If the TV tuner module is removed and not replaced, a protective sleeve must be installed on the antenna 
connector, as shown in the following illustration.
Reverse this procedure to install the TV tuner module. 
						

							Removal and replacement procedures
Maintenance and Service Guide4–15
RTC battery
Before removing the RTC battery, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-7). 
5. Remove the mass storage device cover (see “Mass storage device” on page 4-10). 
Remove the RTC battery: 
»Lift the RTC battery from the socket.
Reverse this procedure to install the RTC battery. 
Description Spare part number 
RTC battery449729-001 
						

							4–16Maintenance and Service Guide
Removal and replacement procedures
Memory module
Before removing the memory module, follow these steps: 
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, 
and then shut it down through the operating system. 
2. Disconnect all external devices connected to the computer. 
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then 
unplugging the AC adapter from the computer. 
4. Remove the battery (see “Battery” on page 4-7). 
5. Remove the mass storage device cover (see “Mass storage device” on page 4-10). 
Remove the memory module:
✎The top memory module slot contains the expansion memory module. The bottom slot contains the primary 
memory module.
1. Spread the retaining tabs 1 on each side of the memory module slot to release the memory module. 
(The memory module tilts up.)
2. Remove the memory module 2 by pulling it away from the slot at an angle.
✎Memory modules are designed with a notch 3 to prevent incorrect insertion into the memory 
module slot.
Reverse this procedure to install a memory module. 
Description Spare part number 
4096-MB (1066-MHz, DDR3)577606-001
2048-MB (1066-MHz, DDR3)577605-001
1024-MB (1066-MHz, DDR3)577604-001