HP Pavilion Dv6 6c00 Quad Edition Entertainment Notebook Pc Series Manual

							9.Lift the hard drive (3) out of the hard drive bay.
Adding or replacing a hard drive 61 
						

							Installing a hard drive
1.Insert the hard drive (1) into the hard drive bay.
2.Replace the 4 screws (2) on the hard drive.
3.Connect the hard drive cable (3) to the computer.
4.Replace the hard drive cover:
a.With the battery bay toward you, position the hard drive cover (1) at a 45-degree angle from
the surface of the computer so that the tabs on the underside of the cover align with the
matching slots on the computer.
b.Gently press the hard drive cover (2) down, applying pressure to both the left and right
edges of the cover, until it snaps into place.
5.Replace the battery.
62 Chapter 9   Drives 
						

							6.Turn the computer right-side up, and then reconnect external power and external devices.
7.Turn on the computer.
Adding or replacing a hard drive 63 
						

							Using optical drives (select models only)
Optical drives include the following:
●CD
●DVD
●Blu-ray (BD)
Identifying the installed optical drive
▲Select Start > Computer.
A list of all the devices installed in your computer, including your optical drive, is displayed.
Inserting an optical disc
1.Turn on the computer.
2.Press the release button (1) on the drive bezel to release the disc tray.
3.Pull out the tray (2).
4.Hold the disc by the edges to avoid touching the flat surfaces and position the disc label-side up
over the tray spindle.
NOTE:If the tray is not fully accessible, tilt the disc carefully to position it over the spindle.
5.Gently press the disc (3) down onto the tray spindle until the disc snaps into place.
6.Close the disc tray.
NOTE:After you insert a disc, a short pause is normal. If you have not selected a media player, an
AutoPlay dialog box opens. It prompts you to select how you want to use the media content.
64 Chapter 9   Drives 
						

							Removing an optical disc
There are 2 ways to remove a disc, depending on whether the disc tray opens normally or not.
When the disc tray opens normally
1.Press the release button (1) on the drive bezel to release the disc tray, and then gently pull out
the tray (2) until it stops.
2.Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer
edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
NOTE:If the tray is not fully accessible, tilt the disc carefully as you remove it.
3.Close the disc tray and place the disc in a protective case.
Using optical drives (select models only) 65 
						

							When the disc tray fails to open normally
1.Insert the end of a paper clip (1) into the release access in the front bezel of the drive.
2.Press in gently on the paper clip until the tray is released, and then pull out the tray (2) until it
stops.
3.Remove the disc (3) from the tray by gently pressing down on the spindle while lifting the outer
edges of the disc. Hold the disc by the edges and avoid touching the flat surfaces.
NOTE:If the tray is not fully accessible, tilt the disc carefully as you remove it.
4.Close the disc tray and place the disc in a protective case.
66 Chapter 9   Drives 
						

							Sharing optical drives
Although your computer may not have an integrated optical drive, you can access software and data,
and install applications, by sharing an optical drive connected to another computer in your network.
Sharing drives is a feature of the Windows operating system that allows a drive on one computer to
be accessible to other computers on the same network.
NOTE:You must have a network set up in order to share an optical drive; refer to Networking
on page 18 for additional information on setting up a network.
NOTE:Some discs, such as DVD movies and game discs, may be copy-protected and therefore
unusable through DVD or CD drive sharing.
To share an optical drive:
1.From the computer with the optical drive you are sharing, select Start > Computer.
2.Right-click the optical drive you want to share, and click Properties.
3.Select the Sharing tab > Advanced Sharing.
4.Select the Share this folder check box.
5.Type a name for the optical drive in the Share name text box.
6.Click Apply, and then click OK.
7.To view the shared optical drive:
Select Start > Control Panel > Network and Internet > Network and Sharing Center.
Using optical drives (select models only) 67 
						

							10 Memory modules
Adding or replacing memory modules
The computer has two memory module slots. The memory module slots are located on the bottom of
the computer under the hard drive cover. The memory capacity of the computer can be upgraded by
adding a memory module or replacing the existing memory module in one of the memory module
slots.
WARNING!To reduce the risk of electric shock and damage to the equipment, unplug the power
cord and remove all batteries before installing a memory module.
CAUTION:Electrostatic discharge (ESD) can damage electronic components. Before beginning
any procedure, ensure that you are discharged of static electricity by touching a grounded metal
object.
NOTE:To use a dual-channel configuration with a second memory module, be sure that both
memory modules are identical.
To add or replace a memory module:
CAUTION:To prevent information loss or an unresponsive system:
Shut down the computer before adding or replacing memory modules. Do not remove a memory
module while the computer is on, in the Sleep state, or in Hibernation.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the
power button. Then shut down the computer through the operating system.
1.Save your work and shut down the computer.
2.Disconnect all external devices connected to the computer.
3.Unplug the power cord from the AC outlet.
4.Turn the computer upside down on a flat surface.
5.Remove the battery from the computer.
NOTE:For more information, refer to Inserting or removing the battery on page 41.
68 Chapter 10   Memory modules 
						

							6.Slide the battery release latch (1) until the cover is released, and then lift up and remove the
cover (2).
7.If you are replacing a memory module, remove the existing memory module:
a.Pull away the retention clips (1) on each side of the memory module.
The memory module tilts up.
b.Grasp the edge of the memory module (2), and then gently pull the module out of the
memory module slot.
CAUTION:To prevent damage to the memory module, hold the memory module by the
edges only. Do not touch the components on the memory module.
To protect a memory module after removal, place it in an electrostatic-safe container.
Adding or replacing memory modules 69 
						

							8.Insert a new memory module:
CAUTION:To prevent damage to the memory module, hold the memory module by the edges
only. Do not touch the components on the memory module.
a.Align the notched edge (1) of the memory module with the tab in the memory module slot.
b.With the memory module at a 45-degree angle from the surface of the memory module
compartment, press the module into the memory module slot (2) until it is seated.
c.Gently press the memory module (3) down, applying pressure to both the left and right
edges of the module, until the retention clips snap into place.
CAUTION:To prevent damage to the memory module, be sure that you do not bend the
module.
9.Replace the memory module compartment cover:
a.With the battery bay toward you, position the memory module compartment cover (1) at a
45-degree angle from the surface of the computer so that the tabs on the underside of the
cover align with the matching slots on the computer.
70 Chapter 10   Memory modules