HP P2055 Manual

3.Grasp the bottom front of the cover, and then  gently separate the cover from the product.
Figure 6-31   Remove the left cover (3 of 4)
4.Carefully slide the cover toward the fron t of the product, and then remove it.
Figure 6-32   Remove the left cover (4 of 4)
ENWW External panels, covers, and doors 119 

Rear cover, rear door, and duplex-paper-feed assembly
NOTE:Only the HP LaserJet P2050 Series products  have a duplex-paper-feed assembly installed.
CAUTION:The fuser can be hot while the product is in use. Wait for the fuser to cool before handling
it.
1. Remove the following components:
● Right cover. See 
Right cover on page 115
.
● Left cover. See 
Left cover on page 118
.
2. HP LaserJet P2050 Series  only: Pull down on the green duplex-paper-feed-assembly release tab,
and then lower the assembly....

3.Remove five screws (callout 1).
Figure 6-34   Remove the rear cover, rear door, and duplex-paper-feed assembly (2 of 6)
1
4.Release one tab (callout 2).
Figure 6-35   Remove the rear cover, rear door, and duplex-paper-feed assembly (3 of 6)
2
ENWW External panels, covers, and doors 121 

5.Carefully separate the rear cove r and rear door from the product, and then remove them.
NOTE:For the HP LaserJet P2050 Series, the duplex-paper-feed assembly is removed with the
cover and door
Reinstallation tip When you reinstall the rear cover assembly, open the rear door to make sure
that the rear cover fits even against the pro duct chassis before you install the mounting screws.
Figure 6-36  Remove the rear cover, rear door, and  duplex-paper-feed assembly (4 of 6; HP
LaserJet P2030 Series)...

6.HP LaserJet P2050 Series  only: Carefully release two hinge pins (callout 3), and then separate
the rear cover and rear door (callout 4) fr om the duplex-paper-feed assembly (callout 5).
Figure 6-38   Remove the rear cover, rear door, and duplex-paper-feed assembly (6 of 6; HP
LaserJet P2050 Series only)
3
5
4
ENWW External panels, covers, and doors 123 

Top-cover assembly
NOTE:The top-cover assembly includes the control panel assembly.
1.Remove the following components:
● Right cover. See 
Right cover on page 115
.
● Left cover. See 
Left cover on page 118
.
● Rear cover, rear door, and duplex-paper-feed assembly. See 
Rear cover, rear door, and
duplex-paper-feed assembly on page 120
.
NOTE: Only the HP LaserJet P2050 Series prod ucts have a duplex-paper-feed assembly
installed.
124 Chapter 6   Removal and replacement ENWW 

2.Remove one screw (callout 1), and then disconnect one connector (callout 2).
Figure 6-39   Remove the top-cover assembly (1 of 4; HP LaserJet P2030 Series only)
1
2
Figure 6-40  Remove the top-cover assembly (2 of 4; HP LaserJet P2050 Series only)
1
2
ENWW External panels, covers, and doors 125 

3.Remove three screws (callout 3).
Figure 6-41   Remove the top-cover assembly (3 of 4)
3
4.Lift the top-cover assembly off  of the product to remove it.
Figure 6-42   Remove the top-cover assembly (4 of 4)
126 Chapter 6   Removal and replacement ENWW 

Cartridge-door assembly and front cover
NOTE:The cartridge door assembly includes the cartridge door, Tray 1, and the front cover.
1.Remove the following components:
● Right cover. See 
Right cover on page 115.
● Left cover. See 
Left cover on page 118.
2. Release two tabs, and then disengage the cartri dge-door assembly link arm (callout 1).
TIP:The link arm releases the fuser-pressure lever when the cartridge door is opened.
Figure 6-43   Remove the cartridge door assembly and front cover (1 of 4)
1...

4.Carefully remove the cartridge-door assembly.
Figure 6-45   Remove the cartridge door assembly and front cover (3 of 4)
5.Disengage two hinge pins (callout 3), and then ca refully separate the front cover (callout 4) from
the cartridge door assembly (callout 5).
Figure 6-46   Remove the cartridge door assembly and front cover (4 of 4)
3
4
5
128 Chapter 6   Removal and replacement ENWW