HP LaserJet M3035xs MFP User Manual

Menu itemSub-menu itemSub-menu itemValues and Description
Release and DHCP Renew  menus are available to set
DHCP lease options.
Auto IP : Use automatic link-local IPv4 addressing. An
address in the form 169.254.x.x is assigned
automatically.
Manual : Use the  Manual Settings  menu to configure
TCP/IPv4 parameters.
  DHCP ReleaseThis menu appears if  Config Method was set to
DHCP  and a DHCP lease for the print server exists.
No  (default): The current DHCP lease is saved.
Yes : The current DHCP lease...

Menu itemSub-menu itemSub-menu itemValues and Description
 IPV6 SettingsEnableUse this item to enable or disable IPv6 operation on the
print server.
Off (default): IPv6 is disabled.
On : IPv6 is enabled.
  AddressUse this item to manually configure an IPv6 address.
Manual Settings : Use the Manual Settings  menu to
enable and manually configure a TCP/ IPv6 address.
  DHCPV6 PolicyRouter Specified : The stateful auto-configuration
method to be used by the print server is determined by
a router. The router...

Menu itemSub-menu itemSub-menu itemValues and Description
IPX/SPXEnable Off: Disable the IPX/SPX protocol.
On  (default): Enable the IPX/SPX protocol.
Frame Type Selects the frame-type se tting for your network.
Auto : Automatically sets and limits the frame type to
the first one detected.
EN_8023 , EN_II , EN_8022 , and EN_SNAP : Frame-
type selections for Ethernet networks.
AppleTalkEnable Off  (default): Disable the AppleTalk protocol.
On : Enable the AppleTalk protocol.
DLC/LLCEnable Off (default):...

Menu itemSub-menu itemSub-menu itemValues and Description
  LAN HW TestCAUTIONRunning this embedded test will
erase your TCP/IP configuration.
This test performs an internal loopback test. An internal
loopback test will send and receive packets only on the
internal network hardware. There are no external
transmissions on your network.
Select  Yes to choose this test, or  No to not choose it.
  HTTP TestThis test checks operation of HTTP by retrieving
predefined pages from the device, and tests the...

Menu itemSub-menu itemSub-menu itemValues and Description
 Ping Test
 This test is used to check network communications.
This test sends link-level packets to a remote network
host, then waits for an appropriate response. To run a
ping test, set the following items:
Dest TypeSpecify whether the target device is an IPv4 or IPv6
node.
Dest IPIPV4 : Type the IPv4 address.
IPV6  : Type the IPv6 address.
Packet SizeSpecify the size of each packet, in bytes, to be sent to
the remote host. The minimum is 64...

Menu itemSub-menu itemSub-menu itemValues and Description
 Ping Results Use this item to view the ping test status and results
using the control panel display. You can select the
following items:
Packets SentShows the number of packets (0 - 65535) sent to the
remote host since the most recent test was initiated or
completed.
Packets ReceivedShows the number of packets (0 - 65535) received from
the remote host since the most recent test was initiated
or completed.
Percent LostShows the percent of ping...

Menu itemSub-menu itemSub-menu itemValues and Description
100TX Auto: Limits auto-negotiation to a maximum link
speed of 100 Mbps.
1000TX Full : 1000 Mbps, full-duplex operation.
Print Protocols     Use this item to print a page that lists the configuration
of the following protocols: IPX/SPX, Novell NetWare,
AppleTalk, DLC/LLC.
Table 2-10  Jetdirect menus (continued)
ENWW Use the Administration menu 35
 

Fax Setup
Table 2-11  Fax Setup menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Required SettingsLocation (Countries/regions
listed)Configure the settings that are legally
required for outgoing faxes.
Date/Time  
Fax Header
InformationPhone Number
Company Name 
PC Fax Send    Disabled
Enabled (default) Use this feature to enable or disable PC Fax
Send. PC Fax Send enables users to send
faxes through the device from their
computers if they have the correct driver
installed.
36 Chapter 2...

Menu itemSub-menu itemSub-menu itemValuesDescription
Fax Send SettingsFax Dial Volume Off
Medium (default)
HighUse this feature to set the volume of the tones
that you hear while the device dials the fax
number.
Error Correction
Mode Enabled  (default)
DisabledWhen Error Correction Mode is enabled and
an error occurs during fax transmission, the
device sends or receives the error portion
again.
JBIG Compression Disabled
Enabled  (default)The JBIG Compression reduces fax-
transmission time, which can...

Menu itemSub-menu itemSub-menu itemValuesDescription
Fax Receive SettingsRings To Answer The range varies by
location. The factory
default is 2 rings.Use this feature to specify the number of rings
that must occur before the fax modem
answers.
Ring Interval Default (default)
CustomUse this feature to control the time between
rings for incoming faxes.
Ringer Volume Off
Low  (default)
HighSet the volume for the fax ring-tone.
Blocked Fax
Numbers Add Blocked
NumbersType the fax number
to add.Use this...