HP LaserJet 1320 User Manual

							ENWWRegulatory information  35
A
Regulatory information
This appendix provides information on the following topics:
●USA Federal Communications Commission (FCC)
●Regulatory statements
●Environmental product stewardship program
 
						

							36  Appendix A Regulatory informationENWW
USA Federal Communications Commission (FCC) 
FCC Notice: Class B Statement
CAUTIONBased on Section 15.21 of the FCC rules, changes or modifications to the operation of this product 
without the expressed approval by Hewlett-Packard Company may invalidate its authorized use.
This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection 
against interference when the equipment is operated in a residential installation. This equipment 
generates, uses, and can radiate radio frequency energy and, if it is not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase separation between the equipment and receiver.
●Connect equipment into an outlet on a circuit different from that to which the receiver is 
connected.
●Consult your dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.
Exposure to radio frequency radiation
CAUTIONThe radiated output power of this device is far below the FCC radio frequency exposure limits. 
Nevertheless, the device shall be used in such a manner that the potential for human contact during 
normal operation is minimized.
In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human 
proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
 
						

							ENWWUSA Federal Communications Commission (FCC) 37
Laser safety statement
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration 
has implemented regulations for laser products manufactured since August 1, 1976. Compliance 
is mandatory for products marketed in the United States. The printer is certified as a “Class 1” 
laser product under the U.S. Department of Health and Human Services (DHHS) Radiation 
Performance Standard according to the Radiation Control for Health and Safety Act of 1968.
Since radiation emitted inside the printer is completely confined within protective housings and 
external covers, the laser beam cannot escape during any phase of normal user operation.
WARNING!Using controls, making adjustments, or performing procedures other than those specified in this user 
guide could result in exposure to hazardous radiation.
Canadian regulations
For Indoor Use. This digital apparatus does not exceed the Class B limits for radio noise 
emissions from digital apparatus as set out in the radio interference regulations of the Canadian 
Department of Communications. The internal wireless radio complies with RSS 210 of Industry 
Canada.
Pour LUsage Dintérieur. Le présent appareil numérique n´émet pas de bruits radioélectriques 
dépassant les limites applicables aux appareils numériques de Classe B prescribes dans le 
règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du 
Canada. Le composant RF interne est conforme à la norme CNR-210 d´Industrie Canada.
 
						

							38  Appendix A Regulatory informationENWW
Regulatory statements
European regulatory notice
European Union Notice
Radio Product for Indoor use in Home and Office environment operating in the 2.4 GHz band.
Radio product with the marking
complies with the R&TTE Directive (1999/5/EC) issues by the Commission of the European 
Community.
Declaration of conformity
The Declaration of Conformity complies with ISO/IEC Guide 22 and EN45014. It identifies the 
product, manufacturer’s name and address, and applicable specifications recognized in the 
European community.
Selected EU, EU candidate and EFTA countries/regions
The radio functionality of this equipment (IEEE 802.11b/g wireless LAN) may be used in the 
following EU, EU candidate and EFTA countries/regions:
Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, 
Hungary, Iceland, Ireland, Italy, Latvia (1 May 2004), Liechtenstein, Lithuania, Luxembourg, Malta, 
Netherlands, Norway, Poland (1 May 2004), Portugal, Slovak Republic, Slovenia, Spain, Sweden, 
Switzerland and United Kingdom.
Notice for use in France and Italy
Italy:
License required for use. Verify with your dealer or directly with General Direction for Frequency 
Planning and Management (Direzione Generale Pianificazione e Gestione Frequenze).
E’necessaria una concessione ministeriale anche per l’uso del prodotto. Verifici per favore con il 
proprio distributore o direttamente presso la Direzione Generale Pianificazione e Gestione 
Frequenze.
France: For 2.4 GHz Wireless LAN operation of this product certain restrictions apply: This 
equipment may be used indoor for the entire 2400-2483.5 MHz frequency band (channels 1-13). 
For outdoor use, only 2454-2483.5 MHz frequency band (channels 10-13) may be used. For the 
latest requirements, see http://www.art-telecom.fr
. 
 
						

							ENWWRegulatory statements 39
Declaration of conformity
Declaration of Conformity
according to ISO/IEC Guide 22 and EN45014
Manufacturers Name:Hewlett-Packard Company
Manufacturers Address:11311 Chinden Boulevard
Boise, Idaho 83714-1021, USA
declares that the product
Product Name:HP LaserJet 1320NW
Regulatory Model Number
3)BOISB-0402-01
Product Options:ALL
conforms to the following Product Specifications:
Safety: IEC 60950:1999 / EN 60950:2000
IEC 60825-1:1993 +A1:1997 +A2:2001 / EN 60825-1:1994 +A11:1996 +A2:2001 
(Class 1 Laser/LED Product)
Health EU:1999/519/EC
EMC: CISPR 22:1997 / EN 55022:1998 Class B
1)
EN 61000-3-2:2000
EN 61000-3-3:1995/A1:2001
EN 55024:1998
FCC Title 47 CFR, Part 15 Class B
2)
 / ICES-003, Issue 4 
Radio
4)EN 301 489-1:2002 / EN 301 489-17:2002
EN 300 328-2:2001
Notified Body Number - 0984
Supplementary Information:
The product herewith complies with the requirements of the R&TTE Directive 1999/5/EC Annex IV, EMC 
Directive 89/336/EEC and the Low Voltage Directive 73/23/EEC, and carries the CE-Marking accordingly
1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems
2) This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two Conditions: 
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation
3) For regulatory purposes, this product is assigned a Regulatory model number. This number should not 
be confused with the product name or the product number(s).
4) This product uses a Radio Module Device which regulatory model number is: RSVLD0303
Boise, Idaho USA
July 19th, 2004
For Regulatory Topics Only:
Australia Contact: Product Regulations Manager, Hewlett-Packard Australia Ltd., 
31-41 Joseph Street, Blackburn, Victoria 3130, Australia
European Contact: Your Local Hewlett-Packard Sales and Service Office or 
Hewlett-Packard GmbH, Department HQ-TRE / Standards 
Europe, Herrenberger Straße 140, D-71034 Böblingen, Germany 
(FAX: +49-7031-14-3143)
USA Contact: Product Regulations Manager, Hewlett-Packard Company, 
PO Box 15 Mail Stop 160, Boise, ID 83707-0015, USA 
(Phone: 208-396-6000)
 
						

							40  Appendix A Regulatory informationENWW
Laser statement for Finland
LASERTURVALLISUUS
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
HP LaserJet HP LaserJet 1320NW -laserkirjoitin on käyttäjän kannalta turvallinen luokan 1 
laserlaite. Normaalissa käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen 
ulkopuolelle.
Laitteen turvallisuusluokka on määritetty standardin EN 60825-1 (1994) mukaisesti.
VA R O I T U S !
Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän 
turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren utsättas 
för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
HUOLTO
HP LaserJet 1320NW -kirjoittimen sisällä ei ole käyttäjän huollettavissa olevia kohteita. Laitteen 
saa avata ja huoltaa ainoastaan sen huoltamiseen koulutettu henkilö. Tällaiseksi 
huoltotoimenpiteeksi ei katsota väriainekasetin vaihtamista, paperiradan puhdistusta tai muita 
käyttäjän käsikirjassa lueteltuja, käyttäjän tehtäväksi tarkoitettuja ylläpitotoimia, jotka voidaan 
suorittaa ilman erikoistyökaluja.
VA R O !
Mikäli kirjoittimen suojakotelo avataan, olet alttiina näkymättömälle lasersäteilylle laitteen ollessa 
toiminnassa. Älä katso säteeseen.
VARNING!
Om laserprinterns skyddshölje öppnas då apparaten är i funktion, utsättas användaren för osynlig 
laserstrålning. Betrakta ej strålen.
Tiedot laitteessa käytettävän laserdiodin säteilyominaisuuksista:
Aallonpituus 785-800 nm
Te h o  5  m W
Luokan 3B laser
 
						

							ENWWEnvironmental product stewardship program 41
Environmental product stewardship program 
Protecting the environment
Hewlett-Packard Company is committed to providing quality products in an environmentally sound 
manner. This product has been designed with several attributes to minimize the impact on our 
environment. 
Ozone production
This product generates no appreciable ozone gas (O3).
Energy consumption
Energy usage drops significantly while in PowerSave mode, which saves money without affecting 
the high performance of this product. This product qualifies for E
NERGY STAR® (version 3.0), which 
is a voluntary program to encourage the development of energy-efficient office products.
E
NERGY STAR® is a U.S. registered service mark of the U.S. EPA. As an ENERGY STAR® partner, 
Hewlett-Packard Company has determined that this product meets E
NERGY STAR® guidelines for 
energy efficiency. For more information, see http://www.energystar.gov/
.
Toner consumption
EconoMode uses significantly less toner, which might extend the life of the print cartridge.
Paper use
This product’s automatic/manual duplex (two-sided printing) and N-up printing (multiple pages 
printed on one page) features can reduce paper usage and the resulting demands on natural 
resources.
Plastics
Plastic parts over 25 grams are marked according to international standards that enhance the 
ability to identify plastics for recycling purposes at the end of the product’s life.
HP LaserJet printing supplies
In many countries/regions, this product’s printing supplies (such as print cartridge, drum, and 
fuser) can be returned to Hewlett-Packard through the HP printing supplies returns and recycling 
program. This easy-to-use, free takeback program is available in over 30 countries/regions. 
Multilingual program information and instructions are included in every new HP print cartridge and 
consumables package.
 
						

							42  Appendix A Regulatory informationENWW
HP printing supplies returns and recycling program information
Since 1992, HP has offered HP LaserJet supplies return and recycling free of charge in 86% of 
the world market where HP LaserJet supplies are sold. Postage-paid and pre-addressed labels 
are included within the instruction guide in most HP LaserJet print cartridge boxes. Labels and 
bulk boxes are also available through the web site: at http://www.hp.com/recycle/
.
More than 10 million HP LaserJet print cartridges were recycled globally in 2002 through the HP 
Planet Partners supplies recycling program. This record number represents 26 million pounds of 
print cartridge materials diverted from landfills. Worldwide HP recycled an average of 80% of the 
print cartridge by weight consisting primarily of plastic and metals. Plastics and metals are used to 
make new products such as HP products, plastic trays and spools. The remaining materials are 
disposed of in an environmentally responsible manner.
U.S. recycling returns
For a more environmentally responsible return of used print cartridges and consumables, 
Hewlett-Packard encourages you to use bulk returns. Simply bundle two or more print cartridges 
together and use the single, prepaid, pre-addressed label that is supplied in the package. For 
more information in the U.S., call (800) 340-2445 or visit the HP LaserJet supplies Web site at 
http://www.hp.com/recycle/
.
Non-U.S. recycling returns
Non-U.S. customers should call the local HP sales and service office or visit the 
http://www.hp.com/recycle/
 web site for more information regarding availability of the HP printing 
supplies returns and recycle program.
Paper
This printer is suited for the use of recycled papers when the paper meets the guidelines in the 
HP LaserJet Printer Family Print Media Guide. See the HP LaserJet 1160 and HP LaserJet 1320 
Series Printer User Guide for ordering information. This product is suitable for the use of recycled 
paper according to EN 12281:2003.
Material restrictions
This product does not contain added mercury.
This product does not contain batteries.
Material Safety Data Sheets
Material Safety Data Sheets (MSDS) for supplies containing chemical substances (e.g., toner) can 
be obtained by contacting the HP web site at:
http://www.hp.com/go/msds
 or 
http://www.hp.com/hpinfo/community/environment/productinfo/safety
 
						

							ENWWEnvironmental product stewardship program 43
For more information
For more information on the following HP environmental programs, see 
http://www.hp.com/go/environment/
.
●Product environmental profile sheet for this and many related HP products
●HPs commitment to the environment
●HPs environmental management system
●HPs end-of-life product return and recycling program
●Material safety data sheets
 
						

							44  Appendix A Regulatory informationENWW
OpenSSL Statements
OpenSSL License
Copyright © 1998-2000 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted 
provided that the following conditions are met:
1Redistributions of source code must retain the above copyright notice, this list of conditions 
and the following disclaimer.
2Redistributions in binary form must reproduce the above copyright notice, this list of conditions 
and the following disclaimer in the documentation and/or other materials provided with the 
distribution.
3All advertising materials mentioning features or use of this software must display the following 
acknowledgment:
“This product includes software developed by the OpenSSL Project for use in the OpenSSL 
Toolkit. (http://www.openssl.org/
)”
4The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or 
promote products derived from this software without prior written permission. For written 
permission, please contact [email protected].
5Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear 
in their names without prior written permission of the OpenSSL Project.
6Redistributions of any form whatsoever must retain the following acknowledgment:
“This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit 
(http://www.openssl.org/
)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED 
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN 
NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY 
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES 
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER 
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE 
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young ([email protected]). This 
product includes software written by Tim Hudson ([email protected]).
Original SSLeay License
Copyright © 1995-1998 Eric Young ([email protected]). All rights reserved.
This package is an SSL implementation written by Eric Young ([email protected]). The 
implementation was written so as to conform with Netscape’s SSL.
This library is free for commercial and non-commercial use as long as the following conditions are 
adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, 
lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this 
distribution is covered by the same copyright terms except that the holder is Tim Hudson 
([email protected]).
Copyright remains Eric Youngs, and as such any Copyright notices in the code are not to be 
removed.