HP Designjet Z6200 1524 mm Photo User Manual

							Setup menu
Printing preferencesSelect graphics language [E]  
Print quality Select quality level
Enable maximum detail
Enable EconoMode
Color options Color/Grayscale
Select RGB source profile
Emulate printer
Select CMYK source profile [P]
Select rendering intent [P]
Black point compensation [P]
HP PANTONE® emulation [P]
Paper options Select paper size
Remove top/bottom blanks
Resize
Rotate
Enable mirror image
Enable crop lines
Enable printing paper info
Margins Select margins
Select margins layout [E]
HP-GL/2 options Select palette
Define palette
Enable merge
PS options [P] Select encoding
Select altitude  
Print retrieval Select drying time  
Enable cutter  
ENWW Setup menu
193
Front-panel menus
 
						

							Job management optionsEnable queue [E]  
When to start printing [E]  
Nest options Enable nesting [E]
Select wait time
Enable crop lines [E]
Oversize nested job margin
Autorotate  
Max. number of printed jobs [E]  
Select job recovery mode  
Paper mismatch action  
Front panel options Select language  
Select display contrast  
Enable buzzer  
Select units [E]  
Date and time options View current device time [E]
Set date [E]
Set time [E]
Set time zone [E]
Enable sleep mode  
Sleep mode wait time  
Resets Reset encoder cleaning 
Restore factory settings  
External hard disk Install (or Uninstall) external hard disk  
Accessories DuplexerInstall duplexer
Other accessories Install other accessories
Enable crop lines appears in two places in the menu: under  Paper options (which applies to
individual jobs) and under  Nest options (which applies to nested jobs ). The default value is Off in
both cases.
Select palette  allows you to choose between Softwa re, Palette A, Palette B and Factory.
Define palette  allows you to define the Pale tte A, Palette B and Factory pa lettes. To do so, select one
of the pens, between 0 and 15, afte r which you can change the width or color of the pen. The width
can vary from 0.13 mm (0.0051 in) to 12.0 mm (0.47 in) and the color can vary from 0 to 255.
Manual drying time allows you to choose a drying time from  1 to 1800 s. The default value is 100
s.
Enable nesting  allows you to choose betwee n Off, In order and Optimized order. In order to enable
nesting,  When to start printing  has to be set to After processing .
194 Appendix C   Front-panel menus ENWW
Front-panel menus
 
						

							Image quality maintenance menu
Optimize print quality  
Optimization actions   
Calibrate color   
Align printheads   
Print diagnostic image   
Paper advance calibration Calibrate paper advance 
Adjust paper advance  
Reset paper advance  
Clean printheads Clean all 
Clean (colors)  
Enable color calibration   
ENWW Image quality maintenance menu
195
Front-panel menus
 
						

							Connectivity menu
Gigabit EthernetView information 
View configuration  
Modify configuration  
Restore factory settings  
USB View information 
Jetdirect EIO View information 
View configuration  
Modify configuration  
Restore factory settings  
Advanced Select I/O timeout 
Allow SNMP  
Embedded Web Server Allow EWS
Reset EWS access control
Web Services Printer utility software
Color and paper management
Restore factory settings  
View information shows whether the interface is installed,  whether the IP address is enabled and
whether printing is enabled through this in terface. It also displays the MAC address.
View configuration  shows the following information: Link st ate, IP address, Configuration mode,
Subnet mask, Default ga teway, mDNS service na me and the MAC address.
Modify configuration  allows you to change the IP address , subnet mask, default gateway and idle
timeout. You can also view the ho st name string and choose an IP address configuration method from
BOOTP, DHCP, Auto IP and Manual.
Printer utility software  allows you to enable or disable the use of the HP Utility.
196 Appendix C   Front-panel menus ENWW
Front-panel menus
 
						

							Internal prints menu
Demo printsPrint fine arts demo 
Print B&W photo 1  
Print B&W photo 2  
Print Color photo 1  
Print Color photo 2  
Print retail demo 1  
Print retail demo 2  
Print GIS map  
Print GIS aerial photo  
Print drawing demo  
User information pr ints Print menu map  
Print configuration  
Print usage report  
Print HP-GL/2 palette  
Print PS font list [P]  
Service information prints Print current information 
Print usage information  
Print event logs  
Print calibration status  
Print connectivity config.  
Print all pages  
ENWW Internal prints menu
197
Front-panel menus
 
						

							Information menu
View printer information  
Printer logs System errors  
System warnings  
Printheads  
Ink cartridges  
View printer information displays general printer informat ion including Product name, Product
number, Serial number, Servic e ID, Language, Memory, Disk capacity and Firmware version.
198 Appendix C   Front-panel menus ENWW
Front-panel menus
 
						

							D Front-panel error messages
Under certain circumstances, a front-panel error message appears. Follow the advice in the
Recommendation column to resolve the error.
If an error message appears  on the front panel that is not included in this list, and you are in doubt
over the correct response, contact HP Support. See 
HP Customer Care on page 176 .
Table D-1   Text messages
Message Recommendation
[Color] cartridge has expired Replace the cartridge. See 
Remove an ink cartridge on page 60 and
Insert an ink cartridge on page 62.
[Color] cartridge is missing Insert a cartridge of the correct color. See 
Insert an ink cartridge
on page 62 .
[Color] printhead #[n] error: not pres ent Insert the correct printhead. See 
Insert a printhead on page 66.
[Color] printhead #[n] error: please remove Remove the in correct printhead and insert a new printhead of the correct
type (color and number). See 
Remove a printhead on page 63 and Insert
a printhead on page 66.
[Color] printhead #[n] error: repl ace Remove the non-functional printh ead and insert a new printhead. See
Remove a printhead on page 63 and Insert a printhead on page 66.
[Color] printhead #[n] error: reseat Remove and reinsert  the same printhead, or try cleaning the electrical
connections. If necessary, insert a new printhead. See 
Front panel
recommends reseating or  replacing a printhead on page 165.
[Color] printhead #[n] out of warranty T he printheads warranty has ended, because of the length of time it has
been in operation or because of the volume of ink used. See the  Legal
Information .
[Color] printhead #[n] warranty warn ing The printheads warranty may be in validated by the use of the wrong
kind of ink. See the  Legal Information.
[Warning] internal failure: Unable to crea te print The internal print files are not  available in the printer. Load the internal
print files through the Embedded Web Server.
Faulty cartridge. Replace [color] cartridge Replace the cartridge. See 
Remove an ink cartridge on page 60 and
Insert an ink cartridge on page 62.
IO error Restart the printer. If the prob lem persists, contact HP Support. See 
HP
Customer Care on page 176.
IO warning Try again; if the proble m persists, contact HP Support. See 
HP Customer
Care on page 176.
PDL Error: Ink system not ready Clean the printheads. See 
Clean the printheads on page 165 .
PDL Error: Job clipped The image is too large fo r the paper or for the printer. Load larger paper
if possible, or reduce the image size.
ENWW 199
Error messages
 
						

							Table D-1  Text messages (continued)
Message Recommendation
PDL Error: memory full Restart the printer and try resending the job; if necessary, reduce the
complexity of the job.
PDL Error: out of paper Load more paper.
PDL Error: parsing error The print job is unintelligible to the printer. Try to recreate and resend it.
Check your cable connections.
PDL Error: print mode error The paper type or print quality specified for the job are incorrect.
Change the loaded paper type or the print settings.
PDL Error: printing error Try sending the job again.
PDL Error: virtual memory full Restart the printer and try resending the job; if necessary, reduce the
complexity of the job.
Replace [color] cartridge Replace the cartridge. See 
Remove an ink cartridge on page 60 and
Insert an ink cartridge on page 62.
Reseat [color] cartridge Remove and reinsert the same cartridge. See 
Remove an ink cartridge
on page 60  and Insert an ink cartridge on page 62.
Update: failed. Invalid file Make sure that you ha ve selected the correct firmware update file. Then
try again to perform the update.
Under certain circumstances, a front-panel numeri c error message appears. Follow the advice in the
Recommendation column to resolve the error.
If an error message appears  on the front panel that is not included in this list,  turn off the printer and
then turn it back on. If the problem persists, contact HP Support. See 
HP Customer Care on page 176 .
Table D-2   Numeric error messages
Error code Recommendation
26:n.01 (where n = the
subject ink cartridge number) Remove the subject ink cartridge and reinstall it in the printer. If the error persists, replace the
subject ink cartridge. If the problem persists, contact HP Support. See 
HP Customer Care
on page 176.
29:01 The maintenance cartridge is not inserted correctly. Open the maintenance cartridge door on the right side of the printer, make sure that the maintenance cartridge is correctly seated, and
then close the door. If the problem persists, re place the maintenance cartridge. If the problem
persists, contact HP Support. See 
HP Customer Care on page 176 .
32:1.01 A take-up reel error has occurred. Make sure that the paper is adequately taped to the take-up reel spindle core, and then make sure that the winding direction is correctly set.
32:2.01 The take-up reel can not be detected. Make  sure that the take-up reel sensor cable is correctly
connected.
200 Appendix D   Front-panel error messages ENWW
Error messages
 
						

							Table D-2  Numeric error messages (continued)
Error code Recommendation
61:01 Unsupported file format: the printer cannot process the job. Try the following remedies:
● Turn off the printer by using the 
Power key on the front panel and the power switch at the
back of the printer; disconnect the power co rd; then reconnect the power cord and turn
on the printer.
● Make sure that the graphic language setting is correct. See 
Change the graphic
language setting on page 26
.
● Resubmit the file to the printer.
● Check that your printer firmware is up to date. See 
Update the printer firmware
on page 138
.
If the problem persists, contact HP Support. See 
HP Customer Care on page 176.
61:04.1 The PostScript fonts are missing. Install the latest firmware release to reinstall the fonts. See
Update the printer firmware on page 138.
61:04.2 Unrecognized paper type identifier. Install th e latest firmware release to reinstall the paper
type identifiers. See 
Update the printer firmware on page 138.
61:08 The paper type has changed. Please resubmit the job.
61:08.1 The file cannot be printed because it is  password-protected. Please resubmit the job without
password protection.
61:08.2 The job contains format errors or incorrect setting values. Please resubmit the job.
63:04 An input/output problem has occurred with the network card. Try the following remedies:
●Make sure that the network cable is co
rrectly connected to the network card.
● Check that your printer firmware is up to date. See 
Update the printer firmware
on page 138
.
If the problem persists, contact HP Support. See 
HP Customer Care on page 176.
71:03 An “out of memory” failure has occu rred. Turn off the printer by using the Power  key on the
front panel and the power switch at the back of  the printer; disconnect the power cord; then
reconnect the power cord and turn on the printer.
71:08 Insufficient display list memory. Please resubmit the job with one or more of the following
changes: reduce resolution  to 300 dpi, select Econofast print mode, select ‘Send Job As
Bitmap’ to have the main processing of the print  job done by the computer rather than by the
printer.
74:01 An error occurred when uploading the firm ware update file. Try the following remedies:
● Turn off the printer by using the 
Power key on the front panel and the power switch at the
back of the printer; disconnect the power co rd; then reconnect the power cord and turn
on the printer.
● Try again to upload the firmware update file to the printer. See 
Update the printer
firmware on page 138.
If the problem persists, contact HP Support. See 
HP Customer Care on page 176.
76:03 The hard disk is full. Use the Embedded We b Server to remove unnecessary files from the
printers hard disk.
If the problem persists, contact HP Support. See 
HP Customer Care on page 176.
ENWW 201
Error messages
 
						

							Table D-2  Numeric error messages (continued)
Error code Recommendation
77:04 An Embedded Web Server internal software  error has occurred. Try the following remedies:
● Turn off the printer by using the 
Power key on the front panel and the power switch at the
back of the printer; disconnect the power co rd; then reconnect the power cord and turn
on the printer.
● Check that your printer firmware is up to date. See 
Update the printer firmware
on page 138
.
If the problem persists, contact HP Support. See 
HP Customer Care on page 176.
79 Firmware error. Try the following remedies:
● Turn off the printer by using the 
Power key on the front panel and the power switch at the
back of the printer; disconnect the power co rd; then reconnect the power cord and turn
on the printer.
● Check that your printer firmware is up to date. See 
Update the printer firmware
on page 138
.
If the problem persists, contact HP Support. See 
HP Customer Care on page 176.
81:01, 81:03, 86:01 Open the printer window and make su re that there are no obstacles restricting the movement
of the drive roller. If the paper has jammed and is restricting the movement of the drive roller,
lift the paper load lever and clear the obstruction. If the problem persists, contact HP Support.
See 
HP Customer Care on page 176.
202 Appendix D   Front-panel error messages ENWW
Error messages