HP Color LaserJet CP6015xh User Manual

3.Slide the tray into the product. The control panel shows the tray type and size configuration. To
specify custom dimensions, or if the type is not correct, press the checkmark button 
 when the
control panel prompts to change the size or type.
4.Select CUSTOM, and then input the X and Y dimensions of the custom paper size.
NOTE:Refer to the label in the paper tray, or to the figure below, to determine the X and Y
dimensions.
YX
5.If the configuration is correct, press the back arrow .
Load large-size...

●For SRA3-sized paper, rotate the lever all the way to the left.
●For A3- or 11x17-sized paper, rotate the lever down into the center position.
●For RA3- or 12x18-sized paper, rotate the lever all the way to the right.
5.Slide the tray into the product. The control panel shows the tray’s media type and size. If the
configuration is not correct, press the checkmark button 
. If the configuration is correct, press
the back arrow 
.
98 Chapter 7   Paper and print media ENWW
 

Configure trays
The product automatically prompts you to configure a tray for type and size in the following situations:
●When you load paper into the tray
●When you specify a particular tray or media type for a print job through the printer driver or a
software program and the tray is not configured to match the print-job’s settings
The following message appears on the control panel:Tray  [type] [size] To change size or type
press the checkmark button 
. To accept settings press the back arrow ....

Configure a tray by using the Paper Handling menu
You can also configure the trays for type and size without a prompt from the product.
1.Press Menu.
2.Press the down arrow 
 to highlight PAPER HANDLING, and then press the checkmark button
.
3.Press the down arrow 
 to highlight the size or type setting for the desired tray, and then press the
checkmark button 
.
4.Press the up arrow 
 or the down arrow  to highlight the size or type. If you select a custom size,
select the unit of measure, and then use...

●The product assumes that the second and all subsequent pages are of the same media type as
the first page.
●This is the second-fastest mode, and is useful for using stacks of the same media type.
Transparency only
●The product does not stop any pages for sensing but distinguishes between transparencies
(Transparency mode) and paper (Normal mode).
●This is the fastest mode and is useful for high-volume printing in Normal mode.
For more information about setting these options, see 
Print Quality menu on...

Choose an output location
Standard output bin
The product has a standard output bin for printed pages. 
When you send print jobs to the product from a computer, the output is routed to the standard output
bin or to one of the output bins on the optional 3-bin stapler/stacker or booklet maker finisher.
Optional output accessories
An optional stapler/stacker or booklet maker can be installed with the product. When an accessory is
installed, an output accessory bridge is also added on top of the product in...

FoldingSingle-sheet print jobs can be automatically folded in the center.
Job offsetEach copy of a job is shifted to one side in the output bin in order to keep each copy separate
from the others. (Supported paper sizes: A3, A4, A4 rotated, A5, B4, B5, Ledger, Legal, Letter,
Letter rotated, Statement.)
Two operation modesMailbox Mode assigns each bin to a user or group of users, and Stacker Mode uses both
output bins for all print jobs — when the top bin is full, jobs are routed to the next bin....

Figure 7-2  Booklet-maker finisher accessory
5642
1
3
1Booklet output bin
2Stacking output bins
3Front door
4Stapler units
5Top cover
6Connection cable
Configure the accessory operation mode
Select the operating mode at the control panel
You can set the operating mode for the 3-bin stapler/stacker or the booklet maker finisher at the product
control panel.
1.At the control panel, press Menu.
2.Press the down arrow 
 to highlight the CONFIGURE DEVICE menu, and then press the
checkmark button 
.
3.Press...

4.Press the down arrow  to highlight OPERATION MODE, and then press the checkmark button
.
5.Select the operation mode that you want to use.
●When Mailbox Mode is used, each bin is assigned to a user or group of users. Every time a
user sends a print job, the job is routed to the assigned bin.
●When Stacker Mode is used and the optional 3-bin stapler/stacker is installed, the three bins
act as a single bin. When one bin is full, jobs are automatically routed to the next bin. When
Stacker Mode is used and...

106 Chapter 7   Paper and print media ENWW