HP Color LaserJet CP6015dn User Manual

Install memory
You can install more memory for the product by adding a dual inline memory module (DIMM).
CAUTION:Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic
wrist strap, or frequently touch the surface of the DIMM antistatic package and then touch bare metal
on the product.
Install DDR memory DIMMs
1. Turn the product off.
2.Disconnect all power and interface cables.
ENWW Replace supplies 157
 

3.Locate the black formatter pressure release tabs on  the formatter board in the rear of the product.
4.Gently press the black tabs toward each other.
5.Gently pull on the black tabs to pull the formatte r board from the product. Place the formatter board
on a clean, flat, grounded surface.
158 Chapter 11   Manage and maintain the product ENWW
 

6.If you are adding a DIMM to slot 2, locate the hard  disk release tab on the bottom of the formatter
board, and then pinch the tab to release the end of the hard disk assembly.
7. Rotate the end of the hard disk assembly upward  until you can disengage the hinge tabs at the
other end.
8. Leaving the hard disk assembly plugged in, lay it to the side to allow space to add or replace the
DIMM in slot 2.
9. To replace a DIMM that is currently installed in  either slot, spread the latches apart on each...

11.Holding the DIMM by the edges, align the notch  on the DIMM with the bar in the DIMM slot at an
angle and firmly press the DIMM into the slot until  it is fully seated. When installed correctly, the
metal contacts are not visible.
XOXOXOXOXOXO
XOXOXOXOXOXO
XO XOXO XOXO
XOXOXOXOXO
XOXOXOXOXO
XOXOXOXOXO
XOXOXOXOXOXO XOXOXOXOXOXOXOXOXOXOXOXOXOXO
XOXOXO
XOXOXOXOXOXO
XOXOXO
XOXOXO
XOXOXOXOXOXO
XOXOXOXOXOXOXOXO XOXO
XO XOX OXOXOXO
12. Push down on the DIMM until both latches engage the DIMM.
XOXOXOXOXOXO...

15.Reconnect the power cable and interface cables, and turn the product on.
16.To enable the new memory, see the following section.
Enable memory for Windows
1.Windows XP and Windows Server 2003 (using the default Start menu view) : Click Start, click
Settings, and then click  Printers and Faxes.
-or-
Windows 2000, Windows XP, and Windows Server 2003 (using the Classic Start menu
view) : Click  Start, click Settings , and then click  Printers.
-or-
Windows Vista : Click Start, click Control Panel , and...

Install an HP Jetdirect or EIO print server card or EIO hard disk
This product is equipped with two external I/O (EIO ) slots. You can install an additional HP Jetdirect
print server card or a hard disk in the available slots.
1. Turn the product off.
2.Disconnect all power and interface cables.
162 Chapter 11   Manage and maintain the product ENWW
 

3.Locate an open EIO slot. Loosen and remove the two retaining screws holding the cover for the
EIO slot, and then remove the cover. You will not need these screws and the cover again. They
can be discarded.
4.Firmly insert the HP Jetdirect print server card into the EIO slot.
5.Insert and tighten the retaining screws that came with the print server card.
ENWW Replace supplies 163
 

6.Reconnect the power cable and remaining in terface cables, and turn the product on.
7.Print a configuration page. An HP Jetdirect confi guration page that contains network configuration
and status information should also print.
If it does not print, turn the product off, and then  uninstall and reinstall the print server card to ensure
that it is completely  seated in the slot.
8. Perform one of these steps:
● Choose the correct port. See the computer or operating system documentation for...

2.Push up to on the staple cartridge to remove  it from the booklet maker or stapler/stacker.
3.Insert the replacement staple cartridge unit into the stapler unit.
4.Push the staple cartridge unit into the st apler unit until it clicks into position.
5.Close the front door.
ENWW Replace supplies 165
 

Replace saddle stitch staple cartridges in the booklet maker
1.Open the front door of the booklet maker.
2.Grasp the blue handle and pull the staple carriage out of the booklet maker.
3.Grasp the small blue handle on the staple cartridge  unit and pull it toward you, then swing the staple
cartridge unit into an upright position.
2
1
4. Grasp the edges of each staple cartridge and pull  up firmly to remove the staple cartridges from
the staple cartridge unit.
166 Chapter 11   Manage and maintain the...