HP Color LaserJet CM1015 User Manual

Print a memory card index
1.Insert the memory card into the MFP. See Insert a memory card. Press Photo Features to choose
one of these options:
●Index print
●Best Photo
●Fast
2.Press Up arrow or Down arrow to select Index print then press OK.
3.Press Up arrow or Down arrow to select either Best Photo or Fast, then press OK.
The MFP prints an index that includes small preview images for each photo on the memory card. Each
index page can contain as many as 30 preview images.
ENWWPrint a memory card index 97
 

98 Chapter 10   PhotoENWW
 

11 Network Setup and Administration
(HP Color LaserJet CM1017 MFP)
●Set up the MFP and use it on the network
NOTEConfiguring TCP/IP settings are complicated and should only be performed by
experienced network administrators. In order for automatic TCP/IP configuration to take place,
either a BOOTP or DHCP Server must be present. For additional help or network configuration,
contact the network administrator.
NOTEThis MFP does not support HP Jetdirect devices.
ENWW99
 

Set up the MFP and use it on the network
Hewlett-Packard recommends using the HP software installer available on the MFP CD-ROMs to install
necessary software in the following network setups.
Configure a network port-connected MFP configuration (direct mode
or peer-to-peer printing)
In this configuration, the MFP is connected directly to the network, and all computers on the network
print directly to the MFP.
NOTEThis mode is the recommended network configuration for the MFP.
1.Connect the MFP directly...

NOTEThis configuration supports printing from the client workstations. Client are not able to
initiate a scan from the MFP.
1.Insert the MFP CD-ROM into the computer. If the MFP is already set up, click Install Software to
start the software installer. If the software installer does not start, navigate to the hpzsetup.exe file
on the CD-ROM and double-click the file.
2.On the Welcome screen, click Next and follow the prompts.
3.For Windows 2000, on the Installation Options screen, choose the installation...

Use the control panel
●Network configuration page
●
Configuration page
●
IP configuration
●
Link speed settings
Network configuration page
The Network configuration page lists the current network settings and other MFP properties. To print
the Network configuration page from the MFP:
1. On the control panel, press  Menu.
2. Press the navigation arrows to select  Reports, then press  OK.
3. Press the navigation arrows to select  Network report, then press OK.
Configuration page
The Configuration page...

9.Press OK to move the cursor to the next triplet. When the address is complete press OK to bring
up the confirmation screen.
10.The graphical screen displays Yes. Press OK to save the configuration, or to delete and re-enter
another IP address, press Left arrow or Right arrow, which changes the display to No.
11.After selecting the IP address, enter the subnet mask and default gateway by repeating steps 8–
10. To get subnet mask and default gateway information in Windows XP Pro:
1.Click on Start, select...

NOTEThe setting must match with the network device to which you are connecting (a
network hub, switch, gateway, or computer).
5.Press OK. The MFP may power cycle.
Supported network protocols
This table lists the networking services/protocols supported on the HP Color LaserJet CM1017 MFP.
Table 11-1  Printing
Service nameDescription
port9100 (Direct Mode)Printing service
Line printer daemon (LPD) Printing service
Table 11-2  Network device discovery
Service nameDescription
SLP (Service Location...

Service nameDescription
MFP to generate a unique IP address. For example, the IP
address 169.254.0.10 represents a series of triplets ranging
from 0 to 254; this address is not manually configurable.
TCP/IP
TCP/IP (Transmission Control Protocol/Internet Protocol) is a suite of protocols designed to define the
way computers and other devices communicate with each other over a network.
TCP/IP is rapidly becoming the most used set of protocols because the Internet is based on TCP/IP. If
there is a network...

NOTEWhen assigning IP addresses, always consult the IP address administrator. Setting the
wrong address can disable other equipment operating on the network or interfere with
communications.
Configure IP parameters
TCP/IP parameters (such as IP address, subnet mask, default gateway) can be configured on the MFP
manually (for example, through the embedded Web server, and HP management software), or
automatically downloaded using DHCP or BOOTP each time the MFP is turned on.
When powered on, a new MFP that...