Honeywell Touchpoint 4 Manual

   Commissioning
TP4MAN Issue 3 Apr 06 (MAN0631)60
3-wire 4-20 mA Source
This covers connection to gas detectors such as Sensepoint Plus/Pro.
1 Set up the gas detector.
Refer to the detector’s user manual for details describing how to set up the detector. 
2 Check that all power and electrical connections to the controller, and electrical 
connections to the gas detector are correct.
For gas detector access see its user manual. For detector to controller wiring details see
page 20.
3Follow step 2 on page...

   Maintenance
TP4MAN Issue 3 Apr 06 (MAN0631)61
WARNINGS
Touchpoint 4 is designed for installation and use in indoor safe area 
non-explosive atmospheres. Installation must be in accordance 
with the recognized standards of the 
appropriate authority in the country concerned.
Before carrying out any work ensure local regulations and site procedures 
are followed. 
Access to the interior of the controller, when carrying out any work, 
must only be conducted by trained personnel. Switch off and isolate...

   Maintenance
TP4MAN Issue 3 Apr 06 (MAN0631)62
Troubleshooting
The following table details self-diagnostics/problem solving for Touchpoint 4.
Configuration Fault
ConditionSymptom Action
Power Supply Faults — subject to selected settings 
DC1 normal:
Power LED (green) ON
Battery icon OFFAC supply failed
(

   Maintenance
TP4MAN Issue 3 Apr 06 (MAN0631)63
System Configuration Check Sheet
Controller location  Installed by  Date
Configured by  Date
Calibrated by Date
Contact tel no
Power supply  ......... AC volts  ......... DC volts
Channel
TypeSensePoint detector typeOther detector 
type
 mV input  mA input
Flam.Toxic Oxygen
STDPlus Pro
1...................................
...................................
..
...................................
.
................................... 2
3
4
Comments (Detail...

   Maintenance
TP4MAN Issue 3 Apr 06 (MAN0631)64
System Review Check Sheet/Record
Comments
Company Name  Application Details 
Contact Name
Address
Tel
Mobile
Fax
(Brief application and system overview including ancillary devices)Email
Customer reported problems/specific requests
Checklist
Control System Y N Comments
Is control system mounted in a suitable place?
Daily viewing, access for maintenance?
Is protection suitable for location?
Indoor/outdoor, enclosure IP /NEMA rating?
Are there any visual...

   Maintenance
TP4MAN Issue 3 Apr 06 (MAN0631)65
Are the devices suitable for the relay ratings?
Correct switching power rating or driving other relays?
Other General Comments
Checks carried out by  Date Next check 

   Parts
TP4MAN Issue 3 Apr 06 (MAN0631)65
This chapter lists part numbers for complete controllers, spare items and accessories.
Touchpoint 4 Controllers
Description Part No.
4-Channel 
4 x mA input, 0 x mV input  TPWM4440
3 x mA input, 1 x mV input  TPWM4431
2 x mA input, 2 x mV input  TPWM4422
1 x mA input, 3 x mV input  TPWM4413
0 x mA input, 4 x mV input  TPWM4404
3-Channel 
3 x mA input, 0 x mV input  TPWM4330
2 x mA input, 1 x mV input  TPWM4321
1 x mA input, 2 x mV input  TPWM4312
0 x mA input, 3...

   Parts
TP4MAN Issue 3 Apr 06 (MAN0631)66
Accessories
Spares
Caution Other 3rd party non-approved equipment may be used, but only at 
the users own risk. 
A range of approved 3rd party supplied equipment is available that has been tested to ensure
their operation with the Zareba range of products. Contact a Honeywell Analytics distributor for
details about the range.Description Part No.
mA expansion kit
(includes mA input module, display module, IDC lead, interconnect 
cable and fixings)TP4MAEK 
mV...

   Specifications
TP4MAN Issue 3 Apr 06 (MAN0631)67
General
Environmental
UseWall mounted 1 to 4 channel control panel for the local annunciation of gas 
hazards as detected by the Zareba Sensepoint range of gas detectors. 
Suitable for use as an indoor stand-alone, self-contained installation or as 
part of a larger distributed control system
User Interface
OperationSingle Test/Accept/Reset push button for normal operational use. Three 
further hidden push buttons per module for configuration via...

   Specifications
TP4MAN Issue 3 Apr 06 (MAN0631)68
Common Module
Channel Module
Supply85-265 Vac, 50/60 Hz, auto-sensing 19-30 Vdc, maximum power 160Wac 
and/or 63Wdc
Communications RS485, user configurable address and baud rate (1200, 2400, 4800, 9600, 
19200)
Other Remote accept/reset push button, normally open, momentary close 
to activate 
RelaysCommon Alarm 1 (A1)  Common Alarm 2 (A2)  System Fault (F)
RatingSPCO / 3 A, 240 Vac (non inductive load)
Default SettingLatching
Normally de-energized...