Honeywell Touchpoint 1 Manual

							   Parts
TP1MAN Issue 4_03-10 (MAN0630)
                                                                        \
                                             51
This chapter lists part nu mbers for complete units  and spare/replacement items.
Touchpoint 1 Controllers
Spares
Description Part No.
mV Input TPWM1101
mA Input TPWM1110
Description Part No.
Instruction manual TP1MAN
Wall mounting bracket TP1WMB
mV input module TP1MVIM
mA input module TP1MAIM
mV display module TP1MVDM
mA display module TP1MADM
IDC lead (display to  input module) TP1IDC
Terminal screw and U  clamp (bag of 20) SPPPMTS
Parts 
						

							   Specifications
TP1MAN Issue 4_03-10 (MAN0630)
                                                                        \
                                            52
General
Environmental
Use Wall mounted single 
channel control panel for the  local annunciation of gas 
hazards as detected by the Honeywell Analytics r ange of Sensepoint gas 
detectors. Suitable for small scale, i ndoor installations requiring a self 
contained gas detection and control system
User interface
Operation Single Test/Accept/Reset push-butt
on for normal operational use. Three 
further hidden push buttons for configuration via in tuitive menu system
Backlit 
display Channel status including 
measuring range, units of  measure, digital gas 
reading, bar graph displays 0-100% full  scale, status indicators including 
alarm set point, alarm acti vated, and power health
Other 
Indicators Ultra-bright LEDs: alarm (red), 
power (green), fault (amber)
Audible Alarm 85 dBA at 1 m / 90 dBA at 1  foot, user hush facility, re-activated on new event
Te r m i n a t i o n s Accessed via hinged front cover (latch 
to hold open as required). All cable/
conduit entry via pre-formed knockouts in  gland plate at bottom of controller.
Screw terminals suitable  for use with 0.5 mm
2 (20 AWG) to 2.5 mm2 (14 AWG)
wires. Crimped connection re commended. Take care not to over tighten screw
terminals. The recommended torque sett ing for the terminals is 12 lb in.
IP Rating  Indoor use, IP44 in  accordance with EN60529:1992
Weight  2.5 kg / 5.5 lb (approx.)
Operating 
Temp Range  -10°C to +40°C / 14°F to 104°F continuous (up to +50°C/122°F intermittent)
Operating 
Humidity 
Range  10 to 90% RH (non condensing)
Operating 
Pressure 
Range  90-110 kPa
Storage  -40
oC to +80oC / -40oF to +176oF, 20 to 80% RH (non condensing) 
EMC EN50270
Specifications 
						

							   Specifications
TP1MAN Issue 4_03-10 (MAN0630)
                                                                        \
                                              53
Inputs
Outputs
Supply  Auto-sensing 85-265 Vac, 50/60 Hz , 30 W and/or 18-32 Vdc, 15 W
Detector Type 3 wire mV bridge 2 wire, 4-20 mA, 
loop powered3 wire, 4-20 mA, 
source output
Example Sensepoint Flammable Sensepoint Toxic 
and OxygenSensepoint Plus 
and Sensepoint Pro 
Detector 
Supply mV Bridge Input Module 
Constant current supply: 200 mA 
Self regulating supply voltage 
subject to cable resistance 
Maximum loop resistance: 18 ohms
mA Input Module
Maximum detector current supply: 500 mA
Minimum guaranteed supply voltage 
from the controller: 18 Vdc
input impedance: 100 ohms
Relays  Alarm 1 (A1)  Al arm 2 (A2) Fault (F)
Rating  SPCO/3 A, 240 Vac (non inductive load)
Default 
Settings Latching
Non- Latching
De-energized Energized 
Energize on alarm  De-energize on fault or 
loss of power
Factory setting 20% FS Factory setting 40% FS
User 
Configurable 
Options  Latching/non-latching 
Energized/de-energized 
Rising/falling (oxygen only)  Trip point 10-90% FS  
						

							   Warranty
TP1MAN Issue 4_03-10 (MAN0630)
                                                                        \
                                               54
Warranty
All products are designed and manufactured to the  latest internationally recognized standards by
Honeywell Analytics under a Qual ity Management system that is certified to ISO 9001. As such
Honeywell Analytics warrants  its products against defective  parts and workmanship and will
repair or (at its option) replace any instruments which are or  may become defective under proper
use within 12 months from  date of commissioning by an  approved Honeywell Analytics
representative or 18 months from  date of shipment from Honeywell Analytics, whichever is the
sooner. This warranty d oes not cover disposable  batteries or damage caused by accident,
abuse, abnormal operating conditi ons or poisoning of sensor. 
Defective goods must be returned to Honeywell  Analytics premises accompanied by a detailed
description of any issue. Where  return of goods is not practicable Honeywell Analytics reserves
the right to charge for any site  attendance where any fault is  not found with the equipment.
Honeywell Analytics shall not be liable for any loss or dama ge whatsoever or howsoever
occasioned which may be a  direct or indirect result of the use or operati on of the Contract Goods
by the Buyer or any Party.
This warranty covers instrument and parts sold  to the Buyer only by authorized distributors,
dealers and representatives as appointed by Honeywell Analytics. The warranties set out in this
clause are not pro rata, i.e. the  initial warranty period is not extended by virtue of any works
carried out there under. 
						

							Issue 4 03/2010 H_MAN0630_TP1MAN_EMEAIECO_HAA100021© 2010 Honeywell Analytics11079
Contact Honeywell Analytics:  
Find out mor e
www .honeywellanalytics.com
Eur ope, Middle East, Africa, India
Life Safety Distribution AG
Weiherallee 11a
CH-8610 Uster
Switzerland
Tel: +41 (0)44 943 4300
Fax: +41 (0)44 943 4398
[email protected]
Americas
Honeywell Analytics Inc. 
405 Barclay Blvd.
Lincolnshire, IL 60069
USA
Tel: +1 847 955 8200 
Toll free: +1 800 538 0363 
Fax: +1 847 955 8210
[email protected]
www .honeywell.com
Technical Services
EMEAI: 
[email protected]
US:        [email protected]
AP:        [email protected]
Asia Pacific 
Honeywell Analytics Asia Pacific 
#508, Kolon Science Valley (I) 
187-10 Guro-Dong, Guro-Gu 
Seoul, 152-050 
Korea 
Tel: +82 (0)2 2025 0300
Fax: +82 (0)2 2025 0329
[email protected]
Please Note:While every effort has been made to ensure accuracy in this publication, no responsibility can be accepted for errors or omissions. Data may change, as well as legislation, and you are strongly advised to obtain copies of the most recently issued regulations, standards, and guidelines. This publication is not intended to form the basis of a contract.