Honeywell series TouchCenter Keypads 6272 User Manual

 
Security (Contd) 
21 
SCREEN ACTION  
2.  Remove zone bypasses by pressing 
the CLEAR BYPASSES button.  
Note:  Bypassed zones are indicated by 
the Bypass icon 
. 
 
3. The User Authorization screen is 
displayed with the instructions To Clear 
Bypasses, Enter Code. 
Note:   If the system is armed and you 
unbypass a zone, it will disarm the 
system. 
4. Enter your 4-digit user code.  The 
More Choices screen is displayed 
showing the system  as Ready to Arm . 
Note:   This will not occur if any...

 
Security (Contd)   
22 
How to Hide a Control Panel Message 
When the Control Panel Message is displayed, press the HIDE 
button to address the condition later. 
SCREEN ACTION   
1. Press the HIDE button to clear the 
Control Panel Message later. 
How to Disarm the System 
IMPORTANT:  If you return and the main burglary sounder is on, 
DO NOT enter the premises, but call the police from a nearby safe 
location. If you return after an alarm has occurred and the main 
sounder has shut itself off, the...

 
Security (Contd) 
23 
SCREEN ACTION 
Note: If you have a comm ercial system  
and a time window has been defined for 
when you may disarm the system , the 
system  will not disarm if you are outside 
that time window. 
To disarm the system when already in the premises:  
SCREEN ACTION   
1. Press the DISARM button on the  
Arm ed screen. The User Authorization 
screen is displayed with the instructions 
“ To Disarm, Enter Code ”. 
  
 
2. Enter your 4-digit user code.  If the Arm 
Multi-Partitions...

 
Security (Contd)   
24 
SCREEN ACTION  
3.  Press the DISARM ALL button if you 
wish to disarm the system.  The 
TouchCenter beeps once and the Arming 
screen is displayed showing the system as 
Ready to Arm  or not ready if any zone is 
faulted (open).  
Note:   If you wish to disarm only selected 
partitions, you must first highlight the 
partition(s) to be disarmed, then press the 
DISARM SELECTED button.   The 
TouchCenter beeps once and the Arming 
screen is displayed showing the system as 
Ready...

 
Security (Contd) 
25 
partition. (Note that only those partitions authorized and 
programmed by the installer can be accessed in this manner.) 
To check the status of other partitions perform the following: 
1.  From the Hom e screen, press the SECURITY button.  The Arming screen  
is displayed.
 
SCREEN   ACTION 
2. Press the Current Partition tab (lower 
edge of the screen; in this case it displays 
P1H).  The User Authorization screen is 
displayed with the instructions “ For 
Authorized Partitions,...

 
Security (Contd)   
26 
Fire Alarm Operation 
Your fire alarm system (if installed) is on 24 hours a day, providing 
continuous protection.  In the event of an emergency, the installed 
smoke and heat detectors will automatically send signals to your 
Control/Communicator, triggering a loud interrupted sound from the 
keypad.  An interrupted sound will also be produced by optional 
exterior sounders.  A FIRE message will appear at your keypad and 
remain on until you silence the alarm. 
In Case of Fire...

 
Security (Contd) 
27 
4. When the problem has been corrected, clear the display by 
entering the DISPLAY FAULTS  button on the Arming screen, 
selecting the fire zone, pressing the  CLEAR button and then 
entering your user code. 
Note:  Contact your Security Company for servicing if you have 
further problems with your fire system. 
In Case of Carbon Monoxide Alarm 
1.   In the event of a carbon monoxide emergency, the CO detector 
will automatically send signals to your Control/Communicator,...

 
Security (Contd)   
28 
carbon monoxide zone, pressing the CLEAR button and then 
entering your user code. 
Note:  Contact your Central Station/Security Company for servicing if 
you have further problems with your carbon monoxide system. 
Advanced System Features 
While most of the commonly used security functions are available 
from the TouchCenter’s advanced user interface, there are some less 
used, advanced features that can either be accessed through Console 
Emulation mode on the TouchCenter or...

 
Security (Contd) 
29 
Console Emulation Mode 
Console Emulation Mode allows you to use a TouchCenter interface 
just as you would a regular system keypad.  All commands shown in 
Console Emulation mode can also be executed from a standard alpha 
keypad. 
Notes: 
•   It is recommended that you do not  use the Console Emulation 
Mode to enter GOTO commands. Unsatisfactory operation may 
result from issuing GOTO commands in Console Emulation. 
•   Two button panics (1 & *, 3 & #, and * & #) do not...

 
Security (Contd)   
30 
SCREEN ACTION 
3.  Press the CONSOLE MODE button on 
the More Choices screen.  The Keypad 
screen is displayed. 
4.  Perform functions as you would from a 
regular alpha keypad. 
How to View the Event Log  
Your system has the ability to record various events in a history log 
wherein each event is recorded with the time and date of its 
occurrence.  The control panel must be programmed to record various 
system events in installer programming mode.  
To view the Event Log,...