Honeywell Rcwl330a1000n Manual
Have a look at the manual Honeywell Rcwl330a1000n Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 178 Honeywell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Instruction Manual RCWL300A Premium Por table Wireless Chime & Push 69-2109EFS-05
Installation Instructions 69-2109EFS—05 ii Contents Checking pack contents ............................1Safety ..........................................................2Quick start ..................................................2Open bell push ...........................................3Fit the push battery ...................................3Fit the chime battery ..................................4Sliding window ...........................................4Volume control ...........................................5Use of icons ...............................................6Programming procedures ..........................7Recall function ...........................................8Chime sounds ............................................8Mount bell push .........................................8Chime position ...........................................9Troubleshooting .......................................10Specifications .......................................... 12Disposal and recycling ............................12Declaration ...............................................13Guarantee .................................................13
RCWL300A 1 69-2109EFS—05 Premium Portable Wirefree Chime with Push Thank you for choosing this Honeywell product. Please use the following instructions to ensure correct installation and use. Keep these notes in a safe place for future ref- erence. Checking Pack Contents Unpack your chime kit and identify the following parts: • Chime • Wall mounting bracket • Bell push • CR2032 battery for bell push • 2 x fixing screws for push • 2 x fixing screws for chime • 2 x wall plugs • Adhesive pad • Self-adhesive icons You will need: • 3 X LR6 ‘AA’ Alkaline batteries • A Phillips screwdriver • A small flat bladed screwdriver • A 1/4-in. (6 mm) masonry drill
Installation Instructions 69-2109EFS—05 2 Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. Quick Start The bell push supplied with this kit is pre-programmed to operate with the chime. You need to do the following to get started: • Open the bell push • Fit the push battery • Fit the chime batteries • Check the volume setting When you operate the bell push, the chime will sound and the 1st Icon will flash. If you have additional pushes or you want to assign a different icon to your push, you will need to follow the programming procedure.
RCWL300A 3 69-2109EFS—05 Open the Bell Push Insert a flat bladed screwdriver into the slot A at the base of the push. Carefully lever the cover and base apart (Fig. 1). Fit the Push Battery Insert the CR2032 coin cell. Ensure the face marked ‘+’ is uppermost (Fig. 2). M27199 A M27153 CR2032 + CR2032 + Fig. 1 Fig. 2
Installation Instructions 69-2109EFS—05 Fit the Chime Batteries To remove the chime battery cover, press at point B and slide the cover back 1/4 in. (5 mm), then lift off. Insert 3 x LR6 ‘AA’ alkaline batteries (not supplied). Observe polarity as marked inside the battery compartment. Sliding Window Release the catch (B) and slide open the window. M27200B M27201B Fig. 3
RCWL300A 5 69-2109EFS—05 Volume Control The volume control is behind the slid- ing window on the front of the chime. Initially, set the control to mid-point. After you have tested your system, adjust to the desired volume. M27202 VOLUME CONTROL
Installation Instructions 69-2109EFS—05 6 Use of Icons In addition to the chime sounds, your chime has a visual indication to show which device has activated it. An icon will illuminate when the chime is activated by a bell push or another compatible device. The chime supports 3 icons. The ‘Main door’ and ‘Back door’ icons are usually used for bell pushes. The other icon is intended for use with other compat- ible devices, such as PIR movement detectors and Telephone ring detector. Icons numbered 1 to 3 are also included. The Icons are self-adhesive, supplied in strips of 3. They can be changed, if required, by opening the sliding window of the chime and gently peeling off the strips. If desired, the strips can be cut into individual icons and attached to the chime in a different order. Use the Programming procedure to change the icon associated with a push. MAINDOORBACKDOORALERTSYMBOL
RCWL300A 69-2109EFS—05 Programming Procedure Learn Procedure To enable your chime to learn the identity of your bell push: • Press the l button and keep it pressed. Each Icon will light in turn. When the Icon you want is lit, release the button. • While the Icon you have selected is lit, operate your push. The chime will sound. The Icon will flash. Unlearn Procedure If you want to remove a push from the chime’s memory: • Press the l button and keep it pressed. • Each Icon will light in turn. When the Icon associated with the push to be unlearned is lit, release the button. • Press and hold down both l & buttons, until a ‘beep’ sound is heard.
Installation Instructions 69-2109EFS—05 Changing the Tune Operate the push. While the Icon is flash- ing, press the button. Press the button again and the tune will change. Repeat until the tune you want plays. Recall Function A short push of the l button will flash the Icon that was last in use. Chime Sounds To hear the chime sounds without oper- ating the bell push, press the button. Press the button again and the tune will change. Mount the Push Mount using either the double-sided adhesive pad or the screws provided. (See Fig. 6 ) Test your push before mounting. Avoid mounting to metal structures. M27155 TOP Fig. 6