Home > Honeywell > Wireless Network > Honeywell Rcwl330a1000n Manual

Honeywell Rcwl330a1000n Manual

Here you can view all the pages of manual Honeywell Rcwl330a1000n Manual. The Honeywell manuals for Wireless Network are available online for free. You can easily download all the documents as PDF.

Page 1

Instruction 
Manual 
RCWL300A
Premium Por table Wireless Chime & Push
69-2109EFS-05 

Page 2

Installation Instructions
69-2109EFS—05 ii

Contents Checking pack contents ............................1Safety ..........................................................2Quick start  ..................................................2Open bell push ...........................................3Fit the push battery  ...................................3Fit the chime battery ..................................4Sliding window  ...........................................4Volume control...

Page 3

RCWL300A
 1 69-2109EFS—05

Premium Portable Wirefree Chime with Push
Thank you for choosing this Honeywell product. Please use the following instructions 
to ensure correct installation and use. Keep these notes in a safe place for future ref-
erence.
Checking Pack Contents
Unpack your chime kit and identify the 
following parts:
• Chime
• Wall mounting bracket
• Bell push
• CR2032 battery for bell push
• 2 x fixing screws for push
• 2 x fixing screws for chime
• 2 x wall plugs
• Adhesive pad
•...

Page 4

Installation Instructions
69-2109EFS—05 2

Safety
Before proceeding with the installation, please note the following safety warnings:
• Always follow the manufacturer’s advice when using power tools and wear 
suitable protective equipment (e.g. safety goggles) when drilling holes, etc.
• Before drilling holes in walls, check for hidden electricity cables and water pipes. 
The use of a cable/pipe locator is advisable if in doubt.
Quick Start
The bell push supplied with this kit is pre-programmed to...

Page 5

RCWL300A
 3 69-2109EFS—05

Open the Bell Push
Insert a flat bladed screwdriver into the 
slot A at the base of the push. Carefully 
lever the cover and base apart (Fig. 1).
Fit the Push Battery
Insert the CR2032 coin cell. Ensure the 
face marked ‘+’ is uppermost (Fig. 2).
M27199
A
M27153
CR2032
+
CR2032
+
Fig. 1
Fig. 2 

Page 6

Installation Instructions
69-2109EFS—05 

Fit the Chime Batteries
To remove the chime battery cover, 
press at point B and slide the cover 
back 1/4 in. (5 mm), then lift off. Insert 
3 x LR6 ‘AA’ alkaline batteries (not 
supplied). Observe polarity as marked 
inside the battery compartment.
Sliding Window
Release the catch (B) and slide open 
the window.
M27200B
M27201B
Fig. 3 

Page 7

RCWL300A
 5 69-2109EFS—05

Volume Control
The volume control is behind the slid-
ing window on the front of the chime. 
Initially, set the control to mid-point. 
After you have tested your system, 
adjust to the desired volume.
M27202
VOLUME CONTROL 

Page 8

Installation Instructions
69-2109EFS—05 6

Use of Icons
In addition to the chime sounds, your chime has a visual indication to show which 
device has activated it. An icon will illuminate when the chime is activated by a bell 
push or another compatible device. The chime supports 3 icons.
The ‘Main door’ and ‘Back door’ icons are usually used for bell 
pushes. The other icon is intended for use with other compat-
ible devices, such as PIR movement detectors and Telephone 
ring detector. Icons numbered 1...

Page 9

RCWL300A
  69-2109EFS—05

Programming Procedure
Learn Procedure
To enable your chime to learn the identity 
of your bell push:
• Press the l button and keep it 
pressed. Each Icon will light in 
turn. When the Icon you want is lit, 
release the button.
• While the Icon you have selected is 
lit, operate your push. The chime will 
sound. The Icon will flash.
Unlearn Procedure
If you want to remove a push from the 
chime’s memory:
• Press the l button and keep it 
pressed. 
• Each Icon will light in...

Page 10

Installation Instructions
69-2109EFS—05 

Changing the Tune
Operate the push. While the Icon is flash-
ing, press the  button. Press the  
button again and the tune will change. 
Repeat until the tune you want plays.
Recall Function
A short push of the l button will flash 
the Icon that was last in use.
Chime Sounds
To hear the chime sounds without oper-
ating the bell push, press the  button. 
Press the button again and the tune will 
change.
Mount the Push
Mount using either the double-sided...
Start reading Honeywell Rcwl330a1000n Manual
All Honeywell manuals