Honeywell Fusion 3 User Manual

							SETUP OPTIONS 
5–17 
 
These schedules are created for the general 
installation and have been predefined with basic 
configurations 
All set to Motion – All cameras are set to motion 
recording (24 hours/day, 7 days/week) 
All set to Continuous – All cameras are set to 
continuous recording (24 hours/day, 7 days/week). 
Default Schedule 1 – All cameras are set to: 
! 
8AM-5PM  Continuous recording 
! 
5PM-8AM  Motion recording 
 
1 Pre-Defined Schedules 
Default Schedule 2 – All cameras are set to: 
! 
Motion recording 24 hours/day, 7 days/week. 
! 
Camera 1 associated to sensor input 1 
! 
Camera 2 associated to sensor input 2 
! 
Camera 3 associated to sensor input 3, etc. 
 
2  Day of Week When a day of the week is selected, the currently 
selected schedule for that day
 is modified. 
 
3  Schedule Time Chart Used to select the time for which each schedule 
will be enabled. 
 
4 Schedule Number The Schedule Number is simply a group of 
settings. Up to 32 schedules can be created. Think 
of the schedules as transparency paper with words 
written on them. When placed one on top of 
another, the words can still be seen from the layers 
below. These schedules allow a powerful detailed 
recording schedule to be created. 
 
5 Special Day Recording 
Schedule Customize a schedule for a particular day, such as 
a Parade Day, Holiday, etc. 
 
6  Camera, Sensor, Relay Designate which cameras, sensors, and relays are 
to be used for the given schedule. These also 
correlate the sensors and relay to the camera  
(i.e., which sensors will activate a camera(s), etc.) 
 
7 Alarm Options These are advanced options that send alarm 
events (either motion or sensor) to the remote 
alarm monitor software and FVMS. 
 
8  Power Off Options Allows the user to specify time frames for turning 
off and restarting the DVR unit automatically. 
  
						

							FUSION III DVR Digital Recording and Transmission System 
5–18 
 
5.6.1  DAY OF THE WEEK 
 The Day of Week is simply the day of the week for which the schedule is being edited. 
If WED is checked, Wednesday’s schedule is being edited.  
 The Single Day Selection button allows selection of multiple days at once.  
By selecting the Single Day Selection button placing multiple checks in the boxes is 
allowed, thereby selecting multiple days simultaneously. 
 
 
 
 Clicking on Single Day Selection will cause the button to change to Multi-Day 
Selection this enables you to select multiple days to configure at once, instead of 
changing the day. 
  
5.6.2  CREATING A SIMPLE SCHEDULE (BY EXAMPLE) 
  Creating schedules is easy with a little experience.  
  In the following example, the steps for creating a simple schedule for cameras 1 to 4 
are detailed. 
  
 
The schedule will be as follows: 
  1.  MON-FRI (9AM-5:59PM) all 4 cameras will record using MOTION recording. 
  2.  MON-FRI (6PM-8:95AM) all 4 cameras will record using CONTINUOUS recording. 
  3.  SAT-SUN (12AM-11:59PM) all 4 cameras will record using MOTION recording. 
  
  To do this, a total of 3 schedules will be created.  
						

							SETUP OPTIONS 
5–19 
 
 
Steps 1-6:    Schedule cameras 1-4 to record on MOTION from 9:00am-5:59pm 
Monday through Friday. 
 1. Select Sch01 from the Schedule Number drop down list.  
(This should already be selected by default) 
 2. Select the Single Day Selection button, then select Yes. 
  3.  Place a check in the MON, TUE, WED, THU, and FRI days of the week. 
 4. On the Sch01 line on time selector grid, highlight hours 09-17.  
Press Set. 
 5. Press Camera buttons 1-4 until the green Motion buttons are selected. 
 6. Press Apply to save. 
  
Step 2 Step 3
Step 4
Step 5
Step 1 
						

							FUSION III DVR Digital Recording and Transmission System 
5–20 
 
 
Steps 7-11:   Schedule cameras 1-4 to record on CONTINUOUS from  
6:00pm-8:59am Monday through Friday.
 
 7. Select Sch02 from the Schedule Number drop down list. 
 8. On the Sch02 line again, highlight the hours 18-23 (for 6:00pm-midnight) and 
press Set. 
 9. On the Sch02 line on time selector grid, highlight the hours 00-08 (for midnight to 
8:59am) and press Set. 
 10. Press Camera buttons 1-4 until the Maroon Continuous buttons are selected. 
 11. Press Apply to save. 
  
 
Step 7
Step 9
Step 10
Step 8
  
						

							SETUP OPTIONS 
5–21 
 
 
Steps 12-19:  Schedule cameras 1-4 to record on MOTION from  
12:00am-11:59pm Monday through Friday 
 12. Select the Multi-Day Selection button. 
  13.  Place a check in the SAT days of the week box. 
 14. Select Sch03 from the Schedule Number drop down list. 
 15. Select the Single Day Selection button, then select Yes. 
  16.  Place a check in the SAT and SUN days of the week boxes. 
 17. On the Sch03 line on the time selector grid, highlight hours 00-23  
and press the Set button. 
 18. Press Camera buttons 1-4 until the Green Motion buttons are selected. 
 19. Press Apply to save. 
  
  
Step 14
Step 17
Step 18
Step 12
 
  
						

							FUSION III DVR Digital Recording and Transmission System 
5–22 
 
5.6.3 SCHEDULING SENSORS AND RELAYS (BY EXAMPLE) 
  It is easy to add advanced recording functionality using Sensor Inputs and Relay 
Outputs.  
 SENSOR - Sensor Inputs can be programmed to instantly start one or more cameras 
recording when an alarm occurs. These alarm events can also activate Relay Outputs 
as desired.  
 RELAY OUTPUT - Relay Outputs can be set to activate when motion alarms or sensor 
alarms occur. 
  
 
The schedule will be as follows: 
  1.  SUN-SAT (12AM-11:59PM) Cameras 1 and 2 will be activated on Sensor #3 
and/or Sensor #5, which will then activate Relay Output #7 and #13. 
  2.  SUN-SAT (12AM-11:59PM) Camera 3 will be set to Record on MOTION.  
When motion occurs it will activate Relay Output #7 and #10. 
  3.  SUN-SAT (12AM-11:59PM) Sensor #6 will activate Relay Output #8 when an 
alarm occurs. This event will NOT cause any cameras to record. 
  
  To do this, a total of 3 schedules will be created. 
  
						

							SETUP OPTIONS 
5–23 
 
 
Steps 1-8:    Schedule cameras 1 and 2 to be activated on Sensor # 3 and/or 
Sensor #5 which will then activate Relay Output #7 and #13. 
 1. Select Sch01 from the Schedule Number drop down list.  
(This should already be selected by default.) 
 2. Select the Single Day Selection button, then select Yes. 
  3.  Place a check in the boxes for SUN, MON, TUE, WED, THU, FRI, and SAT days 
of the week. 
 4. On the Sch01 line (time selector grid), highlight the hours 00-23 and press Set. 
 5. Press Camera buttons #1 and #2 until the Red Sensor buttons are selected. 
 6. Press Sensor buttons #3 and #5. 
 7. Press Relay buttons #7 and #13. 
 8. Press Apply to save. 
  
 
 
  
						

							FUSION III DVR Digital Recording and Transmission System 
5–24 
 
 
Steps 9-15:   Schedule camera 3 to record using MOTION.  
When Motion occurs it will activate Relay Output #7 and #10. 
 9. Select Sch02 from the Schedule Number drop down list. 
 10. Select the Single Day Selection button, then select Yes. 
  11.  Place a check in the boxes for SUN, MON, TUE, WED, THU, FRI, and SAT  
days of the week. 
 12. On the Sch02 line (time selector grid), highlight the hours 00-23 and press Set. 
 13. Press Camera button #3 until the green Motion button is selected. 
 14. Press Relay buttons #7 and #10. 
 15. Press Apply to save. 
  
 
 
  
						

							SETUP OPTIONS 
5–25 
 
 
Steps 16-22:  Schedule Sensor #6 to activate Relay #8 when an Alarm occurs. 
NOTE - This will not cause any cameras to record. 
 16. Select Sch03 from the Schedule Number drop down list. 
 17. Select the Single Day Selection button, then select Yes. 
  18.  Place a check in the boxes for SUN, MON, TUE, WED, THU, FRI, and SAT  
days of the week. 
 19. On the Sch03 line (time selector grid), highlight the hours 00-23 and press Set. 
 20. Press Sensor button #6. 
 21. Press Relay button #8. 
 22. Press Apply to save. 
  
 
 
 
  
						

							FUSION III DVR Digital Recording and Transmission System 
5–26 
 
5.6.4  VERIFYING A RECORDING SCHEDULE 
  1.  Select a single day of the week using the selection check box to the left of the 
specified day.  
  2.  Next move down to the schedule grid.  
  3.  Identify the schedule (or schedules) that have specific hours of the day high-lighted 
in light blue color. The horizontal axis of the schedule grid corresponds to the 24 
hours of each day. 
  4.  After verifying that all hours of the selected day are covered by at least one of the 
32 independent schedules (vertical axis of schedule grid) now move your attention 
to the lower half of the schedule interface. 
  5.  In the “Schedule Number:” selection drop down box, select the schedule(s) that 
were defined above for the current day and verify in each schedule number that 
the correct cameras are set to Continuous, Motion or Sensor based recording. 
 
NOTE: If a specific camera is not to be recorded on a given day/schedule 
combination set the camera to “Not Selected”, a white “X”. 
  6.  Proceed to repeat this process for each of the 7 days of the week until certain that 
the desired recording method is configured for each day.